Ferm PRM1011 Owner's manual

Type
Owner's manual

This manual is also suitable for

www.ferm.com
© 2009 Ferm B.V. 0912-21
EN
Original instructions
05
DE
Übersetzung der
Originalbetriebsanleitung
10
NL
Vertaling van de oorspronkelijke
gebruiksaanwijzing
15
FR
Traduction de la notice originale
20
ES
Traducción del manual original
25
PT
Tradução do manual original
31
IT
Traduzione delle istruzioni
originali
36
SV
Översättning av bruksanvisning
i original
42
FI
Alkuperäisten ohjeiden käännös
47
NO
Oversatt fra orginal veiledning
51
DA
Oversættelse af den originale
brugsanvisning
56
HU
Eredeti használati utasítás
fordítása
61
CS
Překlad püvodního návodu k
používání
66
SL
Preklad pôvodného návodu na
použitie
70
PL
Tłumaczenie instrukcji
oryginalnej
75
RU Перевод исходных инструкций 80
EL
Μετάφραση του πρωτοτύπου
των οδηγιών χρήσης
85
ROUTER
PRM1011
GB
5
ROUTER
Thank you for buying this Ferm product.
By doing so you now have an excellent product,
delivered by one of Europeís leading suppliers.
All products delivered to you by Ferm are
manufactured according to the highest standards
of performance and safety. As part of our
philosophy we also provide an excellent customer
service, backed by our comprehensive Warranty.
We hope you will enjoy using this product for
many years to come.
The numbers in the text refer to the diagrams
on page 2-4.
Read the operating instructions
carefully before using this device.
Familiarize yourself with its functions
and basic operation. Service the device
as per the instructions to ensure that it
always functions properly. The
operating instructions and the
accompanying documentation must be
kept in the vicinity of the device.
Contents
1. Technical specifications
2. Safety instructions
3. Mounting accessoires
4. Operation
5. Maintenance
1. TECHNICAL SPECIFICATIONS
Machinedata
Voltage 230 V
Frequency 50 Hz
Power input 1200 W
No load speed/min 9000-30000
Max. cutter diameter 30 mm
Cutting depth 30 mm
Collet 6+8 mm
Weight 3.71 kg
Lpa (sound pressure) 91+3 dB(A)
Lwa (sound power) 102+3 dB(A)
Vibration left handle 1,4+1,5 m/s
2
Vibration right handle 5.4+1.5 m/s
2
Vibration level
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given in
EN 60745; it may be used to compare one tool
with another and as a preliminary assessment of
exposure to vibration when using the tool for the
applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signifi cantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
Package contents
1 Router
6 Cutters (router bits)
1 Parallel guide
1 Template guide
2 Screws
2 Nuts
1 Adapter for dust extraction
1 Dust tube
1 Wrench
1 6 mm Collet
1 8 mm Collet
1 Instruction manual
1 Guarantee card
The router has been designed for professional
routing of wood, wood products and plastics.
Check the machine, loose parts and accessories
for transport damage.
Product information
Fig. A+C
1. On/off switch
2. Handle
3. Base plate
4. Fixing screws for parallel fence
5. Safety catch
6. Collet nut
7. Spindle lock
GB
6
8. Cutting depth adjustment button
9. Wing bolt for depth stop
10. Depth stop
11. Clamping lever
12. Cutting depth scale
13. Adjusting wheel for electronic speed controller
14. Height adjustment button
15. Cutting depth fine-tuning button
16. Dust extraction facility
17. Parallel fence ruler
18. Zero mark
19. Parallel fence
20. Guide rod
21. Depth stop revolver
2. SAFETY INSTRUCTIONS
Explanation of the symbols
Denotes risk of personal injury, loss of
life or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates electrical shock hazard.
The number of revolution of the
machine can be electronically set.
Wear ear and eye protection
The instructions must be kept in a safe place!
1. Please check workpieces for any obstructions
on the surface of the material, such as
protruding nails etc., to protect the router
head.
2. Wait until the router has come to a complete
stop before removing any blocked or routed
material around the cutter. Use a long stick for
this and not your finger.
3. Please keep your hands away from the
routing surface.
4. Immediately switch off the tool as soon as it
starts producing any unusual noise or starts
vibrating excessively.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is
double insulated; therefore no earthwire
is required.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
Immediately switch off the machine when:
Excessive sparking of the carbon brushes and
verticiliosis in the collector.
Interruption of the mains plug, mains lead or
mains lead damage.
Defect switch
Smoke or stench of scorched isolation
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
unplug the tool.
Wait until the machine has come to a
complete standstill and the cutter has
cooled down before replacing a cutter.
Mounting and removing cutters
Fig. B
Only use cutters with a shaft diameter which
corresponds with the size of the collet. Only use
cutters which are suited for the maximum speed
of the machine. The cutter diameter should not
exceed the maximum diameter (see ‘Technical
specifications’).
Press the spindle lock (7) and turn the collet
nut (6) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
GB
7
Open the collet nut using the wrench.
Place the cutter shaft in the collet.
Tighten the collet nut so that the cutter is
locked properly.
Open the collet nut when you want to replace
a cutter.
Adjusting the parallel fence ruler
Fig. A+C
The parallel fence is a useful tool for precision
routing at a fixed distance from the edge of the
workpiece.
Place the desired cutter in the tool.
Loosen the clamping lever (11).
Push the tool down until the cutter sticks out
from the base plate, then retighten the
clamping lever (11).
Place the router onto the workpiece in such a
that the cutter touches the side of the
workpiece. Please ensure that the furthest
protruding part of the cutter touches the
workpiece (by turning the cutter if necessary).
Slide the provided guide rods (20) into the
appropriate holes.
Slide the parallel fence onto the mounted rods
until it is in full contact with the workpiece. The
zero-position is now set.
Attach the ruler (17) to the rod of the parallel
guide. The zero on the ruler must be aligned
with the zero mark (18).
Loosen the parallel fence fixing screw (4) and
move the fence until the desired setting has
been reached. Important: when adjusting the
parallel fence, please take into account the
diameter of the cutter.
Retighten the fixing screw (4).
Mounting the guide bush
Fig. D
The guide bush is a handy aid for cutting a
pattern.
Mount the guide bush (23) on the router base
(3) using the screws (22).
Mounting the adapter for dust extraction
Fig. E+F
Use the dust adapter for the extraction of dust.
Mount the dust adapter (24) with the screws
(22) on the cutter sole (3).
Place the dust tube (25) in the dust output (16).
Place the tube of your vacuum cleaner on the
dust tube (25).
Keep the outlet of the machine behind
the machine for a good view on the
workpiece.
4. OPERATION
The on/off switch
Fig. A
To switch on the tool, press and hold the on/
off switch (1).
If you release the on/off switch (1), the tool will
be switched off.
Switch locking mechanism
You can lock the on/off switch by pressing the
on/off switch (1) and then button (5). The switch
lock can be released by briefly pressing the on/off
switch (1).
Always select a low speed for cutting
plastic workpieces.
Do not put the machine down when the motor is
still running. Do not place the machine on a dusty
surface. Dust particles may enter the mechanism.
Always observe the safety instructions
and applicable regulations.
Operation
Hold the machine in rest position on the workpiece
when switching the machine on or off. The cutter
in the collet may damage the workpiece.
Clamp the workpiece and make sure that the
workpiece cannot slide from under the
machine during the cutting activities.
Hold the machine firmly and move it evenly
over the workpiece. Do not force the machine.
Only use cutters which do not show any signs
of wear. Worn cutters have a negative effect
on the efficiency of the machine.
Always switch off the machine first before
removing the plug from the wall socket.
Speed preselection
The required speed can be preselected with
GB
8
the thumbwheel (13). Also during running the
rotational speed can be adjusted.
1 - 2 = low speed
3 - 4 = medium speed
5 - 6 = high speed
Max = maximum speed
The required speed depends of the material
and can be determined by practical testing.
Furthermore router bits with a large diameter
need a lower rotational speed.
Material Diameter Speed stages
router bit
Hardwood > 20 mm 1 - 2
10 - 20 mm 3 - 4
< 10 mm 5 - max
Softwood > 20 mm 1 - 3
10 - 20 mm 3 - 6
< 10 mm 5 - max
Aluminium > 15 mm 1
< 15 mm 1 - 2
Plastic > 15 mm 1 - 2
< 15 mm 2 - 3
After longer periods of working at low speed, allow
the machine to cool down by running it for a few
minutes at high speed with no load.
Height setting of the router column
Fig. G
Button (14) is used to set the maximum height of
the router.
The cutting depth is then fixed. This is usually
necessary when using the tool on a special router
table.
Rough setting:
Loosen the clamping lever (11). The router
can then be pushed down against the spring
force.
Hold button (14) between your thumb and
index finger.
Push the grey button (14) and use your other
hand to push the router down at the same time.
Release the button. The router is now locked
and will no longer return to its original position.
Fine adjustment:
Turn button (14) clockwise. This causes the
router column to slowly move down.
Turn button (14) counter-clockwise. This
causes the router column to slowly move up.
Setting of the cutting depth
Fig. G
The cutting depth can be adjusted by using
buttons 8, 9, 11 and 15. If the cutting depth is set
correctly, the groove in question can be routed
accurately to within 0.1 mm.
Preparation:
Place the desired cutter in the tool.
Loosen the clamping lever (11). The router can
then be pushed down against the spring force.
Push the tool down until the cutter touches the
workpiece, then relock it using the clamping
lever (11).
Loosen button 9 (counter-clockwise).
Set button 15 to zero.
Use button 8 to set the depth all the way
down.
Tighten button 9 (clockwise). The cutting
depth is now set to precisely 0 mm.
Rough setting:
Read the value from the scale (12).
Loosen button 9 (counter-clockwise).
Turn button 8 and re-read the value from the
scale. The difference between the two values
is the cutting depth setting.
For example: If the value on the scale (12)
is 8.5 in the zero-setting and the value is 7.0
after button (8) has been turned, then the
cutting depth has been set to 1.5 cm.
Retighten button 9 (clockwise).
Fine adjustment:
Loosen button 9 (counter-clockwise).
The top button (15) is still set to zero. Give this
button a full counter-clockwise turn, until it is
back in the zero position. The cutting depth is
now 1.0 mm less.
If required, the cutting depth can be set
accurately to within 0.1 mm.
Retighten button 9.
Adjustment using the revolver- depth stop
The revolver-depth stop enables you to quickly
choose between six different cutting depths.
These are also determined by the adjustment of
the depth stop (10).
GB
9
Adjust the required cutting depth by rotating
the revolver-depth stop (21).
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
This machine has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Malfunction
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
Repairs and servicing should only be
carried out by a qualified technician or
service firm.
Cleaning
Regularly clean the device’s casing with a soft
cloth, preferably after each use. Keep the fan slits
free of dust and dirt. Remove stubborn dirt using
a soft cloth, dampened with soapy water. Do not
use solvents such as benzene, alcohol, ammonia,
etc, which might damage the plastic parts.
Lubrication
This device does not need any additional lubrication.
Defects
If a defect appears due to a part wearing out,
please contact the service center on the warranty
card. Separately you will find an exploded view
showing the parts that can be ordered.
Environment
To prevent damage during transport, the
appliance is delivered in a solid packaging which
consists largely of reusable material. Therefore
please make use of options for recycling the
packaging.
Damaged and/or disposed of electrical
or electronic devices must be dropped
off at recycling stations intended for that
purpose.
Warranty
Read the warranty conditions on the separately
supplied warranty card.
Wear of the cutter is not covered by the
guarantee.
94
Spare parts list
Position Description No.
2 Base plate 302124
6+7 Locking knob with spring 302112
8 Dust extraction 302111
21 Collet nut 302125
22 Collet 6 mm 302126
22 Collet 8 mm 302127
41 Lever 302129
51 Switch 302130
63 Brush cover 302131
64 Carbon brush set (2 pcs) 302123
66 Brush holder 302132
94 Parallel guide 302114
95+97(2X) Guiding rod (set) 302005
99 Ruler 302121
100 Spanner 302133
101 Template ring 302122
Exploded view
95
www.ferm.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Ferm PRM1011 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI