Hilti DSH-FSC Operating instructions

Hilti
Brand
Hilti
Model
DSH-FSC
Type
Operating instructions
Montageanleitung de
Assembly Instructions en
Instruction de montage fr
I
struzioni per il montaggio it
Instrucciones de montaje es
Instruções de montagem pt
Montagehandleiding nl
Samlevejledning da
Monteringsanvisning sv
Monteringsveiledning no
Asennusohje fi
Összeszerelési útmutató hu
Instrukcja montażu
pl
Инструкция по сборке ru
Návod na montáž sk
Uputstvo za montažu hr
Navodila za montažo sl
DSH FSC
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
1
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
2 3
4 5
6 7
@
@
;
=
;
% &
+
)
%
( +
+
)
)
(
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
8 9
10 11
12 13
§
·
:
;
$
£
£
$
Q
⁄¡
¡
Q
/
/
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
14 15
16 17
¡
¡
;
Q
Q
⁄¡
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
18 19
20
21 22
W
R
E
Z
T
E
Z
R
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
23 24
25 26
U
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
Page is loading ...
2
en
DSH-FSC floor saw cart assembly instructions
1
. Safety precautions
G Use this floor saw cart only in conjunction with the Hilti DSH 700 or DSH 900 gas
saws.
G Observe the instructions and safety precautions listed in the operating instruc-
t
ions for your Hilti gas saw.
2. Assembling the floor saw cart
2.1 Fitting the handle
Fit the handle 햲 to the frame 햳 and secure it with the screw knob 햴.
2.2 Fitting the wheel axle to the frame
Push the wheel axle 햵 into the holes in the frame 햳 and secure it with the screw
knob 햶.
2.3 Fitting the second wheel
Secure the second wheel 햷 on the wheel axle 햵 by fitting the washer 햸 and split
pin 햹.
2.4 Fitting the front wheel
Fit the front wheel 햺 to the front wheel axle 햾 and secure it with the washer 햻
and split pin 햽.
2.5 Fitting the spray guard
Use the two the screws 헀 to secure the spray guard 햿 to the frame 햳.
10
5
11
98
76
4
32
G Note: The machine mount is set in such a way that the saw arm of the DSH 900-
40 gas saw does not come into contact with the floor when cutting to full depth.
When used with the DSH 900-35, DSH 700-35 and DSH 700-30, the machine
mount must be fitted in a lower position in order to reach full cutting depth.
3.1 Disassembling the machine mount
Remove both hex. nuts 헁 and screws 헂 from the machine mount 헃.
3.2 Fitting the machine mount in the lower position
Insert the two screws 헂 in the upper openings in the machine mount 헃 and secure
the machine mount to the frame 햳 once again.
G Note: When fitting the machine mount, take care to ensure it is aligned centrally.
161514
1312
3. Adjusting the machine mount
4
. Adjusting for straight running
G Note: The floor saw cart is designed so that the gas saw cuts in a straight line
when the mark on the machine mount is in the middle position. If it is found that
the gas saw pulls to one side while cutting, this can be compensated by adjust-
i
ng the position of the machine mount.
4.1 Adjusting the machine mount for straight running
Release the upper hex. nut 헁 on the machine mount 헃 and pivot the rear of the
machine mount toward the side to which the saw tends to pull when cutting.
17
5. Fitting the gas saw to
1
8
2
6
1. Bring the height adjustment lever 헄 into the upper position.
2. Release the screw knob 헆 on the grip clamp 헅.
3. Place the gas saw in the forward section of the machine mount with its wheels
positioned as shown in the illustration and then pivot the grip of the saw
Z
into
the grip clamp 헅.
4. Secure the gas saw by tightening the screw knob 헆.
5
. Fit the water container
U
a
fter filling it.
6. Adjust the position of the handle to bring it into a comfortable working position.
7. Adjust the disc/blade guard.
01_MA_DSH_FSC_P1.qxd:01_BA_DSH_FSH_P1.qxd 7.5.2010 11:16 Uhr Seite 2
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
01_MA_DSH_FSC_P1.qxd:01_BA_DSH_FSH_P1.qxd 7.5.2010 11:16 Uhr Seite 18
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
01_MA_DSH_FSC_P1.qxd:01_BA_DSH_FSH_P1.qxd 7.5.2010 11:16 Uhr Seite 19
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
01_MA_DSH_FSC_P1.qxd:01_BA_DSH_FSH_P1.qxd 7.5.2010 11:16 Uhr Seite 20
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
Hilti Corporation
LI-9494 Schaan
T
el.:+423 / 2342111
Fax:+423 / 2342965
www.hilti.com
Hilti = registered trademark of Hilti Corp., Schaan W 3787 0510 10-Pos. 1 1 Printed in Italy © 2010
Right of technical and programme changes reserved S. E. & O.
431274 / A
*431274*
431274
Printed: 07.04.2015 | Doc-Nr: PUB / 5224914 / 000 / 00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Hilti DSH-FSC Operating instructions

Hilti
Brand
Hilti
Model
DSH-FSC
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents