WHITECROFT LIGHTING Kolo Anti Ligature User manual

Brand
WHITECROFT LIGHTING
Model
Kolo Anti Ligature
Type
User manual

WHITECROFT LIGHTING Kolo Anti Ligature is a robust, vandal-resistant luminaire designed to withstand physical abuse and tampering in challenging environments. Constructed from steel spinning, it features an impact rating of IK10, making it suitable for high-risk areas such as prisons, mental health facilities, and schools. With an ingress protection rating of IP65, it can endure dust and water exposure, ensuring reliable operation in various conditions. Installation requires drilling 12 holes for secure mounting, and anti-tamper screws provide additional protection against unauthorized access.

WHITECROFT LIGHTING Kolo Anti Ligature is a robust, vandal-resistant luminaire designed to withstand physical abuse and tampering in challenging environments. Constructed from steel spinning, it features an impact rating of IK10, making it suitable for high-risk areas such as prisons, mental health facilities, and schools. With an ingress protection rating of IP65, it can endure dust and water exposure, ensuring reliable operation in various conditions. Installation requires drilling 12 holes for secure mounting, and anti-tamper screws provide additional protection against unauthorized access.

Whitecroft Lighting Limited
Burlington Street, Ashton-under-Lyne, Lancashire OL7 0AX
Telephone +44 (0)161 330 6811
Registered No. 3848973 England
Registered Office: As above
Nov 2021 - Rev 4
Kolo Anti-Ligature
MSU Kit
PK/MSUKOLO-IL
SPECIFICATION
Finish RAL 9003
Materials Steel Spinning
Weight 0.3Kg.
Ingress protection IP40 (IP40 KOLO)
IP65 (IP65 KOLO)
Impact Rating IK10
Installation Instruction
TECHNICAL SUPPORT
Telephone: 0161 331 5700
Email: technical@whitecroftlight.com
http://whitecroftlighting.com/
Step 7 - Anti pick mastik can be used around the cirfumference if desired.
Shown in red.
Step 5 -
Install the Kolo product as per its installation instruction.
Line up the 4 screw holes in the rear Kolo housing with the 4 holes marked up
in the picture below.
Step 7 - Install the Kolo Anti-Ligature Bezel, using the 4 anti-tamper screws
supplied into the rivnuts on the kolo backplate. Torqe to 1.2Nm. The anti-tamper
screw require special allen key (3mm with centre hole) or bit (sold
separately
-
HAL-KEY3) ensure screws are sufficiently tightened.
Do not apply Mastick
to this face.
Step 1 - Unpack the contents of the Kolo MSU Kit .
Contents - 1 x Backplate Assembly.
1 x Spinning.
1 x Bag with 4 x 50mm Security Screws.
1 x Installation Leaflet.
Step 4 - Drill out the 12 holes, 8 to secure the back plate and 4 to secure the Kolo fitting.
U
se suitable screw plugs/anchors (Max size 5mm Dia. screw, not supplied).
Replace the Inner ring with the 'L's in allignment to the backplate.
Offer up the wall plate but this time rotate clockwise to line up the mounting holes.
Screw the wall plate in place using 8 screws. These screws need to be min. 40mm long to
reach thought to the wall.
Make sure wall or ceiling is flat to prevent buckling of back plate.
Step 2 - Remove the inner ring from the backplate. Take note of the
orientation of the 'L' s on the top of the inner ring and the centre of the
backplate for assembly allignment later.
Step 2 - Place the back plate on the wall in the orientation shown.
The straight slots inbetween the screw holes are for vertical and horizontal
allignment visual guides. Orientation Placement Is Critical.
For ceiling installation two people would be advisable.
Step 3 - Mark the 12 x 2mm holes indicated on the wall.
Marking up the slots may also help.
Then remove wall plate ready to drill the screw holes.
Position of the 8 Screws.
  • Page 1 1
  • Page 2 2

WHITECROFT LIGHTING Kolo Anti Ligature User manual

Brand
WHITECROFT LIGHTING
Model
Kolo Anti Ligature
Type
User manual

WHITECROFT LIGHTING Kolo Anti Ligature is a robust, vandal-resistant luminaire designed to withstand physical abuse and tampering in challenging environments. Constructed from steel spinning, it features an impact rating of IK10, making it suitable for high-risk areas such as prisons, mental health facilities, and schools. With an ingress protection rating of IP65, it can endure dust and water exposure, ensuring reliable operation in various conditions. Installation requires drilling 12 holes for secure mounting, and anti-tamper screws provide additional protection against unauthorized access.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents