Ohlins YA618 Mounting Instruction

Type
Mounting Instruction
Kit Contents
Shock absorber 36PC YA618 (1 pair)
C-spanner 00710-01 (2)
Öhlins Sticker 00197-01 (2)
Memo Note Sticker 01180-01 (1)
Öhlins Owner’s Manual 07255-01 (1)
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00. Fax +46 8 590 025 80.
www.ohlins.com
© Öhlins Racing AB. All rights reserved.
Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB
is prohibited. Printed in Sweden.
Mounting Instruction
Öhlins shock absorber kit YA618
for Yamaha Grizzly - Rear
with set-up data
Before installing this product, check the
contents of the kit listed below.
If anything is missing, please contact
your nearest Öhlins dealer.
During storage and transportation,
especially at high ambient temperature,
some of the oil and grease used
for assembling may leak and stain
the packaging. This is in no way
detrimental to the product, wipe off the
excessive oil/grease with a cloth.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
Read the Öhlins Owner’s Manual before installing this product
Mounting Instruction YA618_2 Issued 2008-04-21.
This instruction and other documents can be
downloaded from www.ohlins.com
INSTALL THE SHOCK ABSORBER ADJUSTMENTS
SET-UP DATA
1
2
WARNING!
When delivered, the Öhlins shock absorber is
dialed to the recommended settings for the
specific brand and make of the motorcycle.
Before riding, always ensure that the basic
settings made by Öhlins are intact.
!
To set the adjuster:
The turn adjusters have a normal right
hand thread. Turn the damping adjusters
clockwise to fully closed (position zero
[0]). Then, turn counter clockwise to open,
and count the clicks until you reach the
recommended number of clicks. See
Set-up data.
1
Raise the rear end of the vehicle so that the
original shock absorbers are in a neutral
position.
2
Remove the original shock absorbers.
3
Install the Öhlins shock absorbers. The
cylinder head should be at the top and the
piggyback reservoir facing backwards.
Fasten the upper attachment first.
WARNING!
1. It is advisable to have an Öhlins dealer install
the shock absorber.
2. Follow the instructions in the vehicle service
manual when changing the shock absorber.
3. When working on a raised vehicle, make sure
that it is securely supported to prevent it from
tipping over.
!
4
Fasten the lower attachment. Raise or lower
the wheels slightly to make the attachment fit.
5
Tighten the attachment screws to the correct
torque. Consult your ATV Owners manual.
6
Read more about your shock absorber in the
Öhlins Owners Manual. See also Set-up data
for this specific shock absorber kit on the
next page.
NOTE!
Make sure that all bolts are tightened to
the correct torque and that nothing fouls or
restricts movement of the shock absorber
when the suspension is being fully com-
pressed or extended.
Piggyback
reservoir
3
CAUTION!
Do not apply lifting force to the A-arms.
Make sure the vehicle is securely supported
so that it cannot tip. Consult your vehicle
service manual.
1
General facts
Shock absorber length 370.5 mm
Stroke 88.5 mm
Recommended settings
Spring preload 20 mm
Compression damping 12 clicks
Compression damping:
Adjust by turning the knob on top
of the reservoir. Turn clockwise to
increase compression damping, turn
counter clockwise to decrease it.
CAUTION!
Do not use force, delicate sealing
surfaces can be damaged. Handtighten
only.
Spring preload
Use the C-spanner provided in this kit.
Turn the spring platform nut (2a) to set
the spring preload. Lock the setting
with the lock nut (2b).
Read more about settings and adjustments
in your Öhlins Owner’s manual.
2a
2b
A
B
A - B = Spring preload
A Free spring length
B Installed spring length
2
View from the rear
  • Page 1 1
  • Page 2 2

Ohlins YA618 Mounting Instruction

Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI