Fun Generation UA-202 Quick start guide

Brand: Fun Generation

Model: UA-202

Type: Quick start guide

Fun Generation UA-202

The Fun Generation UA-202 is a versatile and easy-to-use USB audio interface that allows you to connect your musical instruments, microphones, and other audio devices to your computer. With its two analog signal inputs and outputs, as well as a built-in Phono preamp, the UA-202 is perfect for a wide range of recording and playback applications.

Some of the possible use cases for the Fun Generation UA-202 include:

Recording your electric guitar or bass directly to your computer
Connecting a turntable to your computer to digitize your vinyl records
Using the UA-202 as a headphone amplifier for listening to music or monitoring your recordings

Fun Generation UA-202

Some of the possible use cases for the Fun Generation UA-202 include:

Recording your electric guitar or bass directly to your computer
Connecting a turntable to your computer to digitize your vinyl records
Using the UA-202 as a headphone amplifier for listening to music or monitoring your recordings

Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • inf[email protected] DocID: 412135_06.06.2017

User manual

This manual contains important information on the safe operation of the product.

Read and follow the safety advices and instructions given. Retain the manual for future

reference. If you pass the product on to others please include this manual.

For the transport and protective packaging, environmentally friendly materials

have been chosen that can be supplied to normal recycling. Ensure that plastic

bags, packaging, etc. are properly disposed of. Do not just dispose of these ma-

terials with your normal household waste, but make sure that they are collected for recy-

cling. Please follow the notes and markings on the packaging.

The plasticiser contained in the rubber feet of this product may possibly react with the

coating of your parquet, linoleum, laminate or PVC oor and after some time cause

permanent dark stains. In case of doubt, do not put the rubber feet directly on the

oor, but use felt-pad oor protectors or a carpet.

Stereo USB Audio Interface

This product is subject to the European Waste Electrical and Electronic Equip-

ment Directive (WEEE) in its currently valid version. Do not dispose of your old

device with your normal household waste. Dispose of this product through an

approved waste disposal rm or through your local waste facility. Comply with

the rules and regulations that apply in your country. If in doubt, consult your local waste

disposal facility.

Safety instructions

Intended use

This device is used to convert analogue audio signals into digital and vice versa.

Any other use or use under other operating conditions is considered to be im-

proper and may result in personal injury or property damage. No liability will be

assumed for damages resulting from improper use.

Danger for children

Ensure that plastic bags, packaging, etc. are disposed of properly and

are not within reach of babies and young children. Choking hazard!

Ensure that children do not detach any small parts from the product.

They could swallow the pieces and choke! Never let children unattended use

electrical devices.

Where to use the product

Never use the product

• in conditions of extreme temperature or humidity

• in extremely dusty or dirty areas

• at locations where the unit can become wet

General handling

• To prevent damage, never use force when handling the product.

• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use

liquid cleaners such as benzene, thinners or ammable cleaning agents.

Features

• Two analogue signal in and outputs

• 1×S/PDIF output (coaxial digital out, stereo)

• Built-in Phono preamp

• Input sensitivity switchable between line and Phono level

• Voltage supply via USB

Operating elements and connections

(

Technical specications

 Frequency response: 22Hz – 20kHz, +/- 0.5dB

 Total harmonic distortion: 0.05% @ 1kHz

 Signal-to-noise ratio: 90dB

 Channel crosstalk: -80dB

 Input impedance: 25kΩ

 Maximum input level: Line: 2dBv | Phono: -36dBv

Using the product

1. Connect the USB port of the device to the USB port of a computer to power

the unit. The control LED then lights up.

2. Connect the output of line-level or Phono devices whose signals you want to

process to the INPUT R / L sockets.

3. When connecting line-level devices (or record players with line-out), set the

input sensitivity switch to the LINE position, when connecting record players

(with Phono output) to the PHONO position.

4. If a connected record player has a separate ground contact, connect it to the

ground contact of the device via a suitable cable.

5. To listen to the connected signal source, connect active speakers or the input

of an amplier with passive speakers to the OUTPUT R / L sockets.

6. You can connect devices with an appropriate input to the S / PDIF output, e.g.

DAT recorders.

 Output impedance: Line: 220Ω | S/PDIF: 75Ω

 Maximum output level: Line: 2dB | S/PDIF: 0.5V PCM stereo

 Converters: Sigma-delta, 16 bit

 Voltage supply: USB, 5V 100mAmax.

 Dimensions (W×H×D): 13.6"×1.11"×2.44" (91.5×28.3×62mm)

 Weight: 0.2lb (0.09kg)

1 S/PDIF output

2 Analogue stereo output L/R

3 Input sensitivity switch

4 Analogue stereo input L/R

5 Ground contact for hum-free connection of Phono devices

6 USB port to connect a computer

7 Control LED, lights up when the device is supplied with

voltage via the USB port

Fun Generation UA-202 Quick start guide

Brand: Fun Generation

Model: UA-202

Type: Quick start guide

Fun Generation UA-202

Some of the possible use cases for the Fun Generation UA-202 include:

Recording your electric guitar or bass directly to your computer
Connecting a turntable to your computer to digitize your vinyl records
Using the UA-202 as a headphone amplifier for listening to music or monitoring your recordings

Download PDF

report