Kohler KELSTON 99030T-4 Installation guide

Kohler
Brand
Kohler
Model
KELSTON 99030T-4
Category
Sanitary ware
Type
Installation guide

Kohler KELSTON 99030T-4 is an exposed bath and shower faucet that offers both style and functionality for your bathroom. With its durable construction and easy-to-use design, this faucet is perfect for any home. The faucet features two handles for precise control of water temperature and volume, as well as a diverter button to switch between the spout and showerhead. The handspray included with the faucet provides added versatility for rinsing off or cleaning the shower. Installation is made simple with the included instructions and all necessary hardware.

Kohler KELSTON 99030T-4 is an exposed bath and shower faucet that offers both style and functionality for your bathroom. With its durable construction and easy-to-use design, this faucet is perfect for any home. The faucet features two handles for precise control of water temperature and volume, as well as a diverter button to switch between the spout and showerhead. The handspray included with the faucet provides added versatility for rinsing off or cleaning the shower. Installation is made simple with the included instructions and all necessary hardware.

1213402-2A-E 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
3. The highest working pressure for handspray & showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handspray,
showerhead and the shower arm away from heater, or it may become damaged and cause injury to the user.
HANDLE OPERATION
Left handle opens with turning counter-clockwise, right handle opens with turning clockwise. Lift the diverter button
gently, handspray works.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
1213402-2A-E 4
INSTALLATION INSTRUCTIONS
99030T-4 Exposed Bath Shower Faucet
99031T-4 Exposed Shower Only Faucet
99030T-4 Exposed Bath Shower Faucet
99031T-4 Exposed Shower Only Faucet
KELSTONKELSTON
ROUGH-IN DIMENSIONS
SERVICE PARTS
185.3
MAX 15.7
71
150±15
82.3
G1/2˝
Ø65
G1/2˝
40.5
20º
160
G1/2˝
185.3
MAX 15.7
71
150±15
Ø65
49.5
G1/2˝
Multi-function Handspray Hose
1500
G1/2˝
G1/2˝
G1/2˝
Ø122
79
255
99031T-499030T-4
89
62
40.6
62
29º
70º
29º
880010
99030T/99031T-4-RGD:831727**
99030T/99031T-4-2BZ:1202014**
99030T/99031T-4-CP:1248781**
880010
1189866**
1030624
864922**
1218659
870721
1170944**
1213392**
864471
77954
865225**
1214971**
3005148
1213393**
1213390**
1213390**
837206
837207
1214820**
1214821**
1213399
870944
3002768
1213400**
1213391**
870992
1045299**
1032149**
56283
1119427
77434
1120988
834638
3006148
78125
78125
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
1213402-2A-E 2
1213402-2A-E 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Faucet
To perform installation, installer must provide G1/2˝ female supply fittings,
spaced 150mm apart and horizontally. The supply fittings should be
vertical and not beyond the finished wall. Hot supply pipe must be located
on the left.
Install the two offset connectors(1) into the hot and cold supply fittings.
Use appropriate thread sealants or thread tape onto the threads.
Adjust the center-to-center distance between the connectors to 150mm
and horizontally. They should extend 44 to 50mm beyond the finished
wall. Apply a ring of plumbers putty around the back edge of the
escutcheon(2). Thread the escutcheons onto the connectors until they
are against the finished wall. Remove any excess putty.
Put the washers(4) into the nuts(3) and tighten the nuts with strap
wrench.
Install the regulator(9) of handspray(5) as needed(shown in regulator
installation instruction). Washers(6) provided with hose(7) must be
installed in each end. Connect the faucet outlet(8) and handspray with
hose.
How to Install the Bracket
Determine a suitable location on the finished wall to install the bracket.
Mark bracket support(11) mounting hole locations on the wall according
to the dimension. Drill two holes on the finished wall, the holes should
match the anchors(10). Install the anchors. Tighten screws(12) to secure
bracket support. Apply a ring of plumbers putty or sealant around the
back surface of the bracket(13). Keep the mounting hole facing
downwards, install the bracket onto the bracket support. Secure the
bracket by tightening the screw(14) with hex wrench(15). Remove any
excess puttty or sealant.
Ensure that all connections are tight. Ensure that the handles are in the
off position.
Turn on the drain and main water supply, and check for leaks. Repair as
needed.
Bath & Shower Faucet:
Remove the handspray(5) and aerator (17) by the key(16). Run hot and
cold water through the faucet for about one minute to remove any debris.
Check for leaks. Remove any debris from the aerator. Shut off the faucet.
Reinstall the aerator and handspray.
Shower Faucet:
Remove the handspray
(5). Run hot and cold water through the faucet for
about one minute to remove any debris. Check for leaks. Shut off the
faucet. Reinstall the handspray.
1
2
5
7
4
8
6-1
9
6-2
3
150mm
44~50mm
Hot
Hot
Cold
Cold
10
40.6
11
12
14
15
13
▲
▲
5
17
16
5
  • Page 1 1
  • Page 2 2

Kohler KELSTON 99030T-4 Installation guide

Kohler
Brand
Kohler
Model
KELSTON 99030T-4
Category
Sanitary ware
Type
Installation guide

Kohler KELSTON 99030T-4 is an exposed bath and shower faucet that offers both style and functionality for your bathroom. With its durable construction and easy-to-use design, this faucet is perfect for any home. The faucet features two handles for precise control of water temperature and volume, as well as a diverter button to switch between the spout and showerhead. The handspray included with the faucet provides added versatility for rinsing off or cleaning the shower. Installation is made simple with the included instructions and all necessary hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents