WARNING! - To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture. This apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases shall be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must be connected to a
mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall remain readily
operable.
Application Drawing
Vi30005 5-Port 1G PoE Powered PoE Switch Installation Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
IP Camera-end Installation
The Smart Choice for Transmission Solutions www.vigitron.com
Important Safety Warning
PoE Switch/PoE Midspan end Installation
- Read and keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should conform to all local
codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture,
dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature exceeds 75°C or
is below - 40°C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at power source,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
- The main plug is used as the disconnect device and shall remain readily operable.
UTP Uplink w/ Remote PoE:
- Connect the network cable coming from the PoE switch or PoE Midspan
to the uplink Ethernet port at rear of Vi30005.
- Plug in the IP/PoE devices to the four ports one the Vi30005's front panel.
- Set 30W/60W based on the type of the remote PoE source
PoE Power is allocated based on the required port power up to 36W starting with
Port 1 having the highest priority. Once the total sum of the PoE power is allocated
no more power will be available to remaining ports.
UTP Uplink w/ Local Power Supply:
- Connect the network cable coming from the PoE switch or PoE Midspan
to the fifth Ethernet port at rear of Vi30005.
- Plug in the IP/PoE devices to the four ports one the Vi30005's front panel.
- Connect the approved local power supply to the power connector of Vi30005.
Fiber SFP Uplink:
Note: The SFP (small format pluggables) must be the same types at both ends of
the fiber cable and must match the fiber cable requirements.
- Plugin the SFP to the SFP socket of Vi30005.
- Connect the fiber cable to the SFP.
- Connect the Vi1120 power supply to the Vi30005 power connector.
Individual ports will be able to provide up to 36W. If more power needed for
approved IP devices use the Vi00016 combination cable to combine two ports.
Starting with ports 1 and 2, connect the IP device to the Ethernet ports of the Vi00016 cable.
UTP link:
- Connect the network cable coming from the Vi30005 Uplink port to one of the
Ethernet ports of the PoE switch or PoE Midspan.
Fiber SFP Link:
- Connect the fiber cable to the SFP port of the network switch.
The SFP must be the same types at both ends of the fiber cable and must match
the fiber cable requirements.
The MaxiCollector Vi30005 is a revolutionary five port 1G Powered PoE
switch. The Vi30005 can accept PoE power from an external source and
provide PoE to all four ports. This eliminates the need for local power
supplies and outlets, and lowers installation costs.
The Vi30005’s plug-and-play eliminates the need for IP addressing. The four
Ethernet port can be directly connected to any IP address and will pass that
device's IP address. Network pre-programmed switching features include
802.1p QoS priority queuing, port based VLAN, MAC addressing up to 2K
full and half duplex operation compliant to 802.3x standards and automatic
address learning and aging.
The Vi30005 takes full advantage of high bandwidth maintaining
10/100/1000Mbps transmission with minimum transmission error and
latency by employing full layer 2 network switching technology. The Vi30005
can be used to connect to multiple remote network devices such as
Megapixel IP cameras, VoIP telephone systems, or wireless transmitters.
Using the Vi1120, 120 watt 57 volt power supply, and any MSA compliant
fiber SFP, the Vi30005 can transmit four cameras over distance of 80Km
while providing 30 watts per port and up to 60 watts for two port using the
Vi0015 combining cable.
Maxii
Net
TM
Fiber Optic
Cat 5/6
PoE Cameras
Vi30005
SFP
The Vi30005 is a PoE powered PoE switch that can be used to power up to four cameras
using PoE.
Powering the Vi30005 and 4 remote cameras using PoE
Connecting the Vi30005 and 4 remote cameras over Fiber Optics
Vi30210
56VDC
Vi10240 Data + 72W PoE
328 ft. (100m)
Data + PoE
328 ft. (100m)
Data
up to 80km
Non-PoE Switch
Vi30005
PoE Camera
PoE Camera
60W PTZ Dome
Vi00016
Data + PoE
328 ft. (100m)
Data + PoE
328 ft. (100m)
Data + 60W PoE
328 ft. (100m)
Vi10120
The Vi30005 can be used to connect to up to 4 cameras at distances up to 80Km over fiber
optics.
Vi30005 MaxiiNet 5-Port PoE Powered 1G PoE Switch
Power
14
23
Link/Act 1G
Port
PoE
Limited Lifetime Warranty
Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in accordance
with these instructions, will be free of defects in material and workmanship for
lifetime defined as the duration period of time until product end of life is announce-
ment. After which Vigitron will continue to provide warranty services for a period of 3
years. Period covering valid warranty will be determined by proof of purchase in the
form of an invoice from an authorized Vigitron dealer.
Warranty will only be provided for as long as the original end user purchaser owns
the product. Warranty is not transferrable. At Vigitron's option, defective product will
be repaired, replaced or substituted with a product of equal value. This warranty
does not apply if, in the judgment of Vigitron, Inc., the Product fails due to damage
from shipment, handling, storage, accident, abuse or misuse, or if it has been used
or maintained not conforming to Product manual instructions, has been modified, or
serial number removed or defaced. Repair by anyone other than Vigitron, Inc. or an
approved agent will void this warranty. Vigitron, Inc. shall not under any circumstanc-
es be liable to any person for any incidental, indirect or consequential damages,
including damages resulting from use or malfunction of the product, loss of profits or
revenues or costs of replacement goods. The maximum liability of Vigitron, Inc.
under this warranty is limited to the original purchase price of the Product only.
Prior to returning any defective Product, the end customer or the reseller from whom
the end customer originally purchased the Product must obtain a Return Materials
Authorization (RMA) number from Vigitron, Inc. All defective Products should be
returned to Vigitron, Inc. with shipping charges prepaid. No collect shipments will be
accepted.
Technical Specifications*
Drawings
Status LEDs
© Copyright 2022 Vigitron, Inc.
TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA • [email protected] • www.vigitron.com
Electrical
Ethernet Interface Standard 10/100/1000BaseT
Fiber Optics 1G, SFP socket, depends on the SFP & fiber type
Power Supply
48-57VDC @ 2A min. for 802.3 at 30W / port
Connectors Ethernet Interface: 5 x RJ-45 Connector
Fiber Optics: SFP Socket
Power: Round 2.5mm cpower onnector
RFC 2544 TCP/IP Packet Transmission
768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet
Compatible with IEEE 802.3af PoE, IEEE 802.3at PoE
Environmental
Humidity 0 to 95%, non-condensing
Temperature Operating: -40°C to +75°C
Storage: -40°C to +85°C
Mechanical
Dimensions 1.2x3.75x5.1 in., 3.0x9.53x13 cm (HxWxL)
Weight 0.70 lb (317.5 g)
Material Aluminum
Accessories
56VDC, 120W External power supply (optional)
*Specifications subject to change without notice.
Front View
Rear View
3.75"
9.53cm
1.2"
3.0cm
Link/Act 1G
LED Name Color Status Function
OFF Power is OFF
ON Power is ON
OFF PoE is OFF
PoE is ON
GREEN ON /
FLASHING Connection is OK, Traffic
ON
OFF No connection
Power GREEN
PoE
GREEN
Link/Ac�vity
Ordering Information
Uplink
Power Input
12/57VDC ---
Link/Act 1G
PoE Input
30W 60W
SFP
Vi30005 5-Port PoE Powered 1G PoE Switch
Power
14
23
Link/Act 1G
Port
PoE
Uplink
Power Input
12/57VDC ---
Link/Act 1G
PoE Input
30W 60W
SFP
OFF 10/100
1G
ON
1G
ORANGE
Vi3005
5-port PoE Layer 2 Network Switch
Part No. Description
-
1
-
2
