HARDWARE LIST: I218-422
1 PC
No.
A
B
C
D
E
Description Sketch Quantity
Bolt Ø5/16" x 2"
Lock Washer Ø5/16"
Flat Washer Ø5/16" x 3/4"
Allen Wrench M4
6 PCS
COMPONENTS LIST: I218-422
No.
1
2
3
Description Sketch Quantity
Headboard
Left Leg
Right Leg 1 PC
1 PC
1 PC
COMPONENTS LIST: I218-402
No.
1
2
Description Sketch Quantity
Bed rails
Slats 4 PCS
2 PCS
COMPONENTS LIST: I218-403
No.
1
2
Description Sketch Quantity
Footboard
Support Leg (for slats) 4 PCS
1 PC
3Decking 8 PCS
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
FOR INDOOR USE ONLY
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
I218-403
I218-402
I218-422
HARDWARE LIST: I218-402
No. Description Sketch Quantity
8 PCS
Hex Wrench 13mm
8 PCS
1 PC
8 PCS
Hanger Bolt Ø5/16" x 3"
Hex Nut Ø5/16"
Wood Screw #4 x 1-1/4"
Half Moon Washer Ø5/16"
F
G
H
I
6 PCS
6 PCS
8 PCS
01-02-2020
Wood Screw #4 x 3/4"
J16 PCS
Page 1/6
B
C
D
HB Backside
A
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
STEP 1: Lay the headboard face down on a soft surface. Attach the left leg and right leg to
headboard by using 6 bolts(A), lock washers(B) and flat washers(C).
Left Leg
Right Leg
STEP 2: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Headboard Side Rail
E
FGH
Slat bearer
I218-403
I218-422
I218-402
STEP 3: Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary. Support Leg
Leveler
This End Up
Slat
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
01-02-2020
Page 2/6
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
I
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
01-02-2020
STEP 5: Put the decking over the slats, secure decking to the slats with wood screws (J) through
the pre-drilled holes in the decking as shown below.
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
JDecking
Slat
Page 3/6
STEP 4: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 5.
Remove the decking and attach slats to the slat bearers with wood screws (I).
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
b
a
FUNCTIONALITY INSTRUCTION
Single Powered USB
Port for Charging on
both sides
I218-422
I218-403
I218-402
OPTION 2: The side rails may be used on either side. Arrange the side rails so the slat
bearers are in LOWER POSITION prior to attachment in STEP 3.
Queen Standard Bed
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
STEP 2: The slat bearers have been attached in position (b) originally. The slat bearers must be
moved into position (a) since using more than a mattress on this bed. Remove the bolts and screws
from the slat bearers and side rails as shown below. Then re-attach the slat bearers to the side rails
in position (a) with bolts, lock washers, flat washers, and screws. Caution: Do not over tighten
bolts as this may loosen the threaded inserts in the side rails.
01-02-2020
Page 4/6
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
STEP 3: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Side Rail
E
FGH
Slat bearer
Support Leg
Leveler
This End Up
Slat
STEP 4: Remove the support legs (top) as shown in the picture
to the right. Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary.
Remove
Support Leg(top)
I
I218-403
I218-422
I218-402
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
01-02-2020
Page 5/6
STEP 5: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 6.
Remove the decking and attach slats to the slat bearers with wood screws (I).
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
FUNCTIONALITY INSTRUCTION
I218-403
I218-402
Single Powered USB
Port for Charging on
both sides
I218-422
Standard Queen Bed
ITEM NO: I218-422-WHT/SHL Queen Uph HB
I218-403-WHT/SHL Queen Low Profile FB
I218-402-WHT/SHL Queen Rails w/ Decking
01-02-2020
STEP 6: Put the decking over the slats, secure decking to the slats with wood screws (J)
through the pre-drilled holes in the decking as shown below.
Decking
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
J
Slat
Page 6/6
HARDWARE LIST: I218-425
1 PC
No.
A
B
C
D
Description Sketch Quantity
Bolt Ø5/16" x 2"
Lock Washer Ø5/16"
Flat Washer Ø5/16" x 3/4"
Allen Wrench M4
6 PCS
COMPONENTS LIST: I218-425
No.
1
2
3
Description Sketch Quantity
Headboard
Left Leg
Right Leg 1 PC
1 PC
1 PC
COMPONENTS LIST: I218-406
No.
1
2
Description Sketch Quantity
Bed rails
Slats 5 PCS
2 PCS
COMPONENTS LIST: I218-407
No.
1
2
Description Sketch Quantity
Footboard
Support Leg (for slats) 5 PCS
1 PC
3Decking 9 PCS
COMPONENTS LIST: I218-410
No.
1
2
Description Sketch Quantity
Bed rails
Slats 5 PCS
2 PCS
3Decking 8 PCS
Page 1/6
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
FOR INDOOR USE ONLY
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
I218-407
I218-406
I218-425
I218-410
6 PCS
6 PCS
01-02-2020
E
HARDWARE LIST: I218-406/410
No. Description Sketch Quantity
8 PCS
Hex Wrench 13mm
8 PCS
1 PC
10 PCS
8 PCS
Hanger Bolt Ø5/16" x 3"
Hex Nut Ø5/16"
Wood Screw #4 x 1-1/4"
Half Moon Washer Ø5/16"
F
G
H
I
J Wood Screw #4 x 3/4"(only for-406) 18 PCS
Wood Cap (only for -410)
16 PCS
8 PCS
Wood Screw #4 x 3/4"(only for-410)
k
L
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
Page 2/6
STEP 1: Lay the headboard face down on a soft surface. Attach the left leg and right leg to
headboard by using 6 bolts(A), lock washers(B) and flat washers(C).
Left Leg
Right Leg
STEP 2: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Headboard Side Rail
E
The outside holes match to 6/6 standard king rails,
the inside holes match to 6/0 Cal king bed rails.
FGH
Slat bearer
I218-407
I218-425
I218-406
I218-410
STEP 3: Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary.
Support Leg
Leveler
This End Up
Slat
HB Backside
B
C
D
A
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
01-15-2020
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
Page 3/6
I
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
01-02-2020
STEP 5: Put the decking over the slats, secure decking to the slats with wood screws (J & L)
through the pre-drilled holes in the decking as shown below.
Decking
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
J
L
I218-406
I218-410
I218-425
I218-425
I218-407
I218-407
J & L
STEP 4: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 5.
Remove the decking and attach slats to the slat bearers with wood screws (I).
b
a
STEP 2: The slat bearers have been attached in position (b) originally. The slat bearers must be
moved into position (a) since using more than a mattress on this bed. Remove the bolts and screws
from the slat bearers and side rails as shown below. Then re-attach the slat bearers to the side rails
in position (a) with bolts, lock washers, flat washers, and screws. Caution: Do not over tighten
bolts as this may loosen the threaded inserts in the side rails.
OPTION 2: The side rails may be used on either side. Arrange the side rails so the slat
bearers are in LOWER POSITION prior to attachment in STEP 3.
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
Page 4/6
STEP 6: For Cal King bed, insert wood caps into the holes on
headboard and footboard. For regular King bed, skip this step. Wood Cap (K)
FUNCTIONALITY INSTRUCTION
Standard king bed
Cal king bed
Single Powered USB
Port for Charging on
both sides
I218-425
I218-425
I218-407
I218-407
I218-406
I218-410
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
01-02-2020
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
Page 5/6
STEP 3: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Headboard Side Rail
E
The outside holes match to 6/6 standard king rails,
the inside holes match to 6/0 Cal king bed rails.
FGH
Slat bearer
I218-407
I218-425
I218-406
I218-410
Support Leg
Leveler
This End Up
Slat
STEP 4: Remove the support legs (top) as shown in the picture
to the right. Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary.
Remove
Support Leg(top)
I
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
01-02-2020
STEP 5: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 6.
Remove the decking and attach slats to the slat bearers with wood screws (I).
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
Page 6/6
STEP 7: For Cal King bed, insert wood caps into the holes on
headboard and footboard. For regular King bed, skip this step. Wood Cap (K)
FUNCTIONALITY INSTRUCTION
Standard king bed
Cal king bed
I218-425
I218-425
I218-407
I218-406
I218-407
I218-410
Single Powered USB
Port for Charging on
both sides
ITEM NO: I218-425-WHT/SHL King Uph HB
I218-407-WHT/SHL King Low Profile FB
I218-406-WHT/SHL King Rails w/ Decking
I218-410-WHT/SHL Cal King Rails w/ Decking
01-02-2020
STEP 6: Put the decking over the slats, secure decking to the slats with wood screws (J & L)
through the pre-drilled holes in the decking as shown below.
J & L
Decking
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
I218-406
I218-410
I218-425
I218-425
I218-407
I218-407
J
L
HARDWARE LIST: I218-522
1 PC
No.
A
B
C
D
E
Description Sketch Quantity
Bolt Ø5/16" x 2"
Lock Washer Ø5/16"
Flat Washer Ø5/16" x 3/4"
Allen Wrench M4
6 PCS
COMPONENTS LIST: I218-522
No.
1
2
3
Description Sketch Quantity
Headboard
Left Leg
Right Leg 1 PC
1 PC
1 PC
COMPONENTS LIST: I218-517
No.
1
2
Description Sketch Quantity
Bed rails
Slats 4 PCS
2 PCS
COMPONENTS LIST: I218-503
No.
1
2
Description Sketch Quantity
Footboard
Support Leg (for slats) 4 PCS
1 PC
3Decking 5 PCS
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
FOR INDOOR USE ONLY
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
HARDWARE LIST: I218-517
No. Description Sketch Quantity
8 PCS
Hex Wrench 13mm
8 PCS
1 PC
8 PCS
Hanger Bolt Ø5/16" x 3"
Hex Nut Ø5/16"
Wood Screw #4 x 1-1/4"
Half Moon Washer Ø5/16"
F
G
H
I
6 PCS
6 PCS
8 PCS
I218-503
I218-522
I218-517
Wood Screw #4 x 3/4"
J10 PCS
Page 1/6
01-15-2020
B
C
D
HB Backside
A
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
STEP 1: Lay the headboard face down on a soft surface. Attach the left leg and right leg to
headboard by using 6 bolts(A), lock washers(B) and flat washers(C).
Left Leg
Right Leg
STEP 2: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Headboard Side Rail
E
FGH
Slat bearer
I218-503
I218-522
I218-517
STEP 3: Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary. Support Leg
Leveler
This End Up
Slat
The holes are for
Hollywood frames
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
01-15-2020
Page 2/6
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
I
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
STEP 4: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 5.
Remove the decking and attach slats to the slat bearers with wood screws (I).
STEP 5: Put the decking over the slats, secure decking to the slats with wood screws (J) through
the pre-drilled holes in the decking as shown below.
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
JDecking
Slat
Page 3/6
01-15-2020
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
b
a
FUNCTIONALITY INSTRUCTION
Single Powered USB
Port for Charging on
both sides
OPTION 2: The side rails may be used on either side. Arrange the side rails so the slat
bearers are in LOWER POSITION prior to attachment in STEP 3.
Twin Standard Bed
I218-503
I218-522
I218-517
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
STEP 2: The slat bearers have been attached in position (b) originally. The slat bearers must be
moved into position (a) since using more than a mattress on this bed. Remove the bolts and screws
from the slat bearers and side rails as shown below. Then re-attach the slat bearers to the side rails
in position (a) with bolts, lock washers, flat washers, and screws. Caution: Do not over tighten
bolts as this may loosen the threaded inserts in the side rails.
Page 4/6
01-15-2020
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
STEP 3: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Side Rail
E
FGH
Slat bearer
Support Leg
Leveler
This End Up
Slat
STEP 4: Remove the support legs (top) as shown in the picture
to the right. Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary.
Remove
Support Leg(top)
I218-503
I218-522
I218-517
The holes are for
Hollywood frames
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
STEP 5: Arrange slats on the slat bearers and then lay the decking on top of the slats. Make sure
the top and bottom slats are situated underneath the pre-drilled holes as shown below in STEP 6.
Remove the decking and attach slats to the slat bearers with wood screws (I).
I
Page 5/6
01-15-2020
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
FUNCTIONALITY INSTRUCTION
Single Powered USB
Port for Charging on
both sides
Twin Standard Bed I218-503
I218-522
I218-517
ITEM NO: I218-522-WHT/SHL Twin Uph HB
I218-503-WHT/SHL Twin Low Profile FB
I218-517-WHT/SHL Twin Rails w/ Decking
STEP 6: Put the decking over the slats, secure decking to the slats with wood screws (J)
through the pre-drilled holes in the decking as shown below.
Decking
Pre-drilled hole
Make sure that there is a slat
under the pre-drilled hole.
J
Slat
Page 6/6
01-15-2020
HARDWARE LIST: I218-525
1 PC
No.
A
B
C
D
E
Description Sketch Quantity
Bolt Ø5/16" x 2"
Lock Washer Ø5/16"
Flat Washer Ø5/16" x 3/4"
Allen Wrench M4
6 PCS
COMPONENTS LIST: I218-525
No.
1
2
3
Description Sketch Quantity
Headboard
Left Leg
Right Leg 1 PC
1 PC
1 PC
COMPONENTS LIST: I218-514
No.
1
2
Description Sketch Quantity
Bed rails
Slats 4 PCS
2 PCS
COMPONENTS LIST: I218-507
No.
1
2
Description Sketch Quantity
Footboard
Support Leg (for slats) 4 PCS
1 PC
3Decking 7 PCS
ITEM NO: I218-525-WHT/SHL Full Uph HB
I218-507-WHT/SHL Full Low Profile FB
I218-514-WHT/SHL Full Rails w/ Decking
Thank you for purchasing this quality product. Be sure to check all packing material carefully for
small parts that may come loose inside the carton during shipment.
UNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
All Beds need to be set up in the exact final
location so that after full assembly it will not
need to be moved. Moving the bed will cause
the support legs to move out of perpendicular
(90 degree), weaken the support system, and
may allow the bed to collapse.
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
BEFORE USING THIS PRODUCT PLEASE READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS.
Save these instructions for future reference.
FOR INDOOR USE ONLY
TOOLS REQUIRED (NOT PROVIDED)
PHILLIPS SCREWDRIVER
HARDWARE LIST: I218-514
No. Description Sketch Quantity
8 PCS
Hex Wrench 13mm
8 PCS
1 PC
8 PCS
Hanger Bolt Ø5/16" x 3"
Hex Nut Ø5/16"
Wood Screw #4 x 1-1/4"
Half Moon Washer Ø5/16"
F
G
H
I
6 PCS
6 PCS
8 PCS
I218-507
I218-525
I218-514
Wood Screw #4 x 3/4"
J14 PCS
Page 1/6
01-15-2020
B
C
D
HB Backside
A
aspenhome
RASSEMBLY INSTRUCTIONS
MADE IN VIETNAM
ah
STEP 1: Lay the headboard face down on a soft surface. Attach the left leg and right leg to
headboard by using 6 bolts(A), lock washers(B) and flat washers(C).
Left Leg
Right Leg
STEP 2: Screw the bolts(E) into HB & FB. Align the bolts with the holes in the end of side rails
and attach the side rails to HB & FB using half moon washer(F),and hex nuts (G).Then use a hex
wrench to tighten all the nuts.
Headboard Side Rail
E
FGH
Slat bearer
I218-507
I218-525
I218-514
STEP 3: Attach the support legs with leveler to the slats.
Adjust the levelers on bottom of support legs when necessary. Support Leg
Leveler
This End Up
Slat
The holes are for
Hollywood frames
ITEM NO: I218-525-WHT/SHL Full Uph HB
I218-507-WHT/SHL Full Low Profile FB
I218-514-WHT/SHL Full Rails w/ Decking
Page 2/6
01-15-2020
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
aspenhome I218-422-WHT Assembly Instructions
- Type
- Assembly Instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
aspenhome I34-451N-SNA Assembly Instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Living Spaces A629-29 User manual
-
Kmart 42950868 User manual
-
GLIDEAWAY SG-22 Operating instructions
-
Living Spaces 329475 User manual
-
Baxton Studio BBT61162-Rattan-Queen Assembly Instructions
-
SHANGRI-LA SHANGRI-LA SLVICFABOKA Victoria Bed User guide
-
Winners Only BV2002Q Assembly Instructions
-
GLIDEAWAY SPS21B Operating instructions
-
ROOMS TO GO 22126038 Assembly Instructions
-
KARPENTER KP08 User manual
