Genaray TIR-1X1B User manual

Brand: Genaray

Model: TIR-1X1B

Type: User manual

USER MANUAL

Bright Beast

1×1 BI-COLOR PANEL

TIR-1X1B

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

THANK YOU FOR CHOOSING GENARAY

The Genaray Bright Beast is a 1×1 bi-color panel that uses 256

LEDs to throw an ultrabright, ﬂicker-free light that’s ideal for

photo and video shoots. It operates on AC power or a single

V-mount battery, and it features 0% to 100% dimming for a full

6 stops of light. Built-in Bluetooth, DMX, and an AC adapter

give you an all-in-one unit that needs no extra components or

accessories for full functionality.

The Bright Beast supports DMX-512 so the light’s settings

can be remotely controlled from a DMX console. It has 512

selectable channels and a 5-pin XLR output jack to daisy-chain

other DMX-compatible lights. The Bright Beast can also be

controlled via Bluetooth with the Bright Beast app, which will

let you operate the light from 30 feet away.

For compatibility in the studio, the yoke can be mounted to a

light stand with a baby pin or junior pin.

Bright Beast

INTRODUCTION

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 3

· Please read and follow these

instructions, and keep this manual in

a safe place.

· Keep this unit away from water and

any ﬂammable gases or liquids.

· Make sure the unit is powered off

when plugging it into a power source.

· Use only the correct, recommended

voltage.

· Handle the unit with care.

· Do not attempt to disassemble or

repair the equipment—doing so will

void the warranty, and Genaray will not

be responsible for any damage.

· Do not stare directly at the lights when

they are powered on.

· Clean the unit with only a soft, dry

cloth.

· Images are for illustrative purposes

only.

PRECAUTIONS

Precautions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

PRODUCT

OVERVIEW

Light Fixture - Front

Yoke

Tilt lock

256 LED

Panel

Barndoor lock

Diffuser

registration

pins

Barndoor brackets

5/8 in. receiver

Locking knob

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 5

Product overview

Light Fixture - Back

Mode selector/

Brightness dial

Color/Set Dial

LCD display

Fan vent Fan power switch

Power switch

AC power input

V-mount

battery plate

V-mount

release button

DMX out

(female)

DMX in (male)

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

MOUNTING INSTRUCTIONSCONTENTS INCLUDE

· LED with yoke

· Power cable

· Carry bag

Mount the Bright Beast on any heavy-duty

light stand with a 5/8-inch baby pin, and turn

the locking knob until secure. Remove the

locking knob to mount the Bright Beast into

a junior receiver.

contents

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 7

POWERING THE

BRIGHT BEAST

FROM AN AC OUTLET

The Bright Beast can be powered directly

from an AC outlet or by a V-mount battery

(not included).

USING THE BRIGHT BEAST WITH AC

POWER

Connect the AC power cable to the Bright

Beast by aligning the tabs and inserting the

cam lock into the AC input. Turn the cam

lock a quarter-turn to the right until it clicks.

Power on the Bright Beast by ﬂipping the

power switch to the AC position.

To unplug the AC cable, pull the AC release,

twist the cam lock a quarter-turn to the left,

and slide the plug out of the socket.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

USING THE BRIGHT BEAST WITH

BATTERY POWER

The Bright Beast can be powered by a

V-mount battery.

When attaching the battery, make sure the

power switch is in the center Off (O) position,

and the ﬁxture is not plugged into a wall

outlet.

Once the battery is mounted, ﬂip the power

switch to the DC position to power on the

light.

Anton-Bauer batteries can be used by

connecting them to the Bright Beast with an

adapter plate (sold separately).

The battery status indicator on the LCD

display shows the remaining battery power.

Tip

The battery loses some of its charge when

not in use. If the battery has not been in use

for several months, Genaray recommends

fully recharging the battery before a shoot.

75% to 100%

50% to 75%

25% to 50%

Less than 25%

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 9

OPERATING THE FAN

SELECTING AN OPERATING MODE

The Bright Beast has three operating

modes: CCT, Effects, and Bluetooth Reset.

Press the Mode Selector button repeatedly

to cycle through and select a mode.

Fast and Slow Scrolling Settings

The scrolling rate setting lets you rapidly

scroll to a color temperature and brightness

or ﬁne-tune the settings.

Press and hold the Mode Selector button for

3 seconds to select Fast or Slow settings. An

F or an S will appear onscreen to indicate

the setting.

· Selecting Fast lets you adjust the color

temperature in 100 K increments, and

brightness in 10% increments.

· Selecting Slow lets you ﬁne-tune the

color temperature in 50 K increments,

and brightness in 1% increments.

The Bright Beast is outﬁtted with a manual

fan control. The fan is extremely quiet, but

it can be switched off if a microphone is

picking up some fan noise.

· When the fan power switch is in the On

position (|), the lights’ brightness can be

adjusted to 100%.

· When the fan power switch is in the

Off position (O), the light’s maximum

brightness is 50%.

USER INTERFACE

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

The Bright Beast is preset with 9 animated

lighting effects that can be selected and

edited on the LCD screen or the Bright

Beast app.

To enter Effects mode, press the Brightness/

Mode dial repeatedly until Effects mode

appears on the screen.

Press the Color/Set Dial repeatedly to

highlight the scene, and turn it to select one

of the 9 preloaded effects.

CCT MODE EFFECTS MODE

CCT mode allows you to adjust color

temperature and brightness.

· Turn the Mode/Brightness Dial to adjust

the brightness.

· Turn the Color/Set Dial to change the

color temperature from 3000 to 5600 K.

instructions

CH 001

078

CCT 5600K

24°S

SCENE

05401

CH 001 24°S

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 11

Screen: Simulates the ﬂicker from a

television with random brightness changes

of bright white light.

Candle Light: Simulates the light of a

candle or ﬁreplace. A constant warm

white light randomly switches and fades at

random intervals between a set range of

brightnesses.

Flash Light: Simulates multiple camera

ﬂashes with short bursts of white light.

Strobe: Rapid, even bursts of white light.

Far and Near Light: A steady pulse of bright

white light with equal intervals of on and off.

Alarm: A steady pulse of warm white light

with equal intervals of on and off.

Heartbeat: Warm white light fades on and

off with a steady rhythmic pulse.

EDITING THE EFFECT

When you select an effect, it immediately

begins playing.

Pressing the Color/Set Dial selects between

DMX channel, scene, speed, and brightness.

DMX Channel: Set the DMX channel

between 000 and 512. (See Using DMX

below)

Speed: Determines how rapidly the effect

plays or cycles. Select between 0 (slowest)

and 10 (fastest).

Brightness: Select between 0% to 100%.

EFFECTS

Lightning 1: Simulates lighting with a cycle

of four short and long bursts.

Lightning 2: Simulates lightning with a cycle

of seven long and short bursts.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

The Bright Beast supports DMX-512 so the

light’s settings can be remotely controlled by

a DMX lighting control console.

To set up DMX operation on the Bright

Beast, follow these steps:

1. Use a 5-pin XLR cable to connect a DMX

controller to the Bright Beast’s DMX input

jack.

2. Use the Bright Beast’s DMX output jack

to connect multiple lights or to insert a

DMX terminator.

3. Set a DMX address by selecting Effects

or Bluetooth Reset mode. Press the

Color/Set Dial until the DMX channel is

highlighted, and turn the dial to set the

DMX address.

Important!

You will need two consecutive DMX

addresses for each light, one to adjust the

light intensity, and another to adjust the

color temperature.

Make sure the DMX address of the Bright

Beast matches the DMX console.

USING DMX

instructions

BT-RESET

ID 66DE

CH 24°S001

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 13

BLUETOOTH

OPERATION

If the app is unable to ﬁnd the Bright Beast,

press the Mode Selector dial until the

Bluetooth Refresh page appears on the LCD

screen.

Press the Color/Set Dial to highlight the

“?” icon, and turn the dial so “OK” appears

onscreen. This resets the Bright Beast’s

built-in Bluetooth, and you will be able to

proceed.

The Bright Beast app is available for iOS

and Android devices. Go to the App Store or

Google Play Store to download the free app,

and install it on your device.

PAIRING THE BRIGHT BEAST WITH

YOUR DEVICE

Open the Bright Beast app, and touch the

Add Device icon.

Your light’s icon will appear in a few

seconds. Press the + icon to the right of the

device to pair it with your device.

instructions

BT-RESET

ID 66DE

CH 001 24°S

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

Once the light has been added, touch its icon

to select a new icon and create a custom

name for the light.

Scroll through the icons, and tap to select.

Type a name for the light in the text ﬁeld.

Press OK to complete pairing the light with

your device.

The paired device screen will appear.

The green ﬂag indicates the light is paired

with your device.

If a red ﬂag appears, the Bright Beast is

powered off or your device is out of range.

Connect the power source to the light, turn it

on, and make sure your device is nearby. In a

few seconds, the green ﬂag will reappear.

Touch the illuminated power icon to pause

the light’s operation. Touch it again to

illuminate the power icon and resume

operation.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 15

CCT MODE

Touch your device on the Bluetooth pairing

screen to bring up the CCT mode screen.

Use the preset buttons to select a color

temperature.

DELETING A DEVICE

To delete the device, press and hold the

name of the device and choose, "Delete

device" from the pull down menu.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

· To set the brightness, touch the +

or – icons on the brightness slider, or

touch the dot and slide it to the desired

brightness.

· To set a custom color temperature, touch

the + or – icons on the color temperature

slider, or touch the dot and slide it to the

desired color temperature.

EFFECTS MODE

Switch to the Effects mode screen from the

CCT screen by touching Scene at the bottom

of the screen.

· Select one of the nine lighting effects.

· Increase or decrease the speed of the

effect by pressing the + or – icons on the

speed slider, or touch one of the preset

speeds.

· To adjust the brightness, touch the +

or – icons on the brightness slider, or

touch the dot and slide it to the desired

brightness.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL 17

USING OPTIONAL

ACCESSORIES

MOUNTING THE BARNDOORS

Align the barndoors with the ﬂat edge on the

bottom and the notched edge on top.

1. Place the bottom edge into the barndoor

brackets.

2. Lift the barndoor lock, press the

barndoors so they’re ﬂush against the

front panel, and release the barndoor

lock to secure it.

MOUNTING THE DIFFUSER

Mount the diffuser onto the panel by aligning

the registration pins on the light with the

holes at the top corners of the diffuser. Once

aligned, the diffuser magnetically attaches

to the Bright Beast’s front panel.

instructions

Bright Beast 1×1 Bi-Color Panel - USER MANUAL

PRODUCT

SPECIFICATIONS

LED Type: SMD

LED Count: 256 (Amber: 128, White: 128)

Brightness @ 3 ft.: 3200 K: 18,700 lx

5600 K: 19,800 lx

Beam Angle: 45°

CRI: 3200 K: 97

5600 K: 96

TLCI: 3200 K: 98

5600 K: 97

Output Power: 100 W

Working Voltage: AC: 100–240 V

DC: 18 V @ 5.6 A

Mount: 5/8 in., baby pin convertible to 1 1⁄8 in.

junior pin

Dimensions:

Light only:

11.75 × 11.75 × 3.25 in. (29.8 × 29.8 × 8.2 cm)

With yoke:

15.25 × 17 × 4 in. (38.7 × 43.2 × 10.2 cm)

Weight: 9 lb. (4.1 kg) with yoke, without battery

sPecifications

ONE-YEAR LIMITED WARRANTY

This Genaray product is warranted to the original purchaser to be free from defects in materials and

workmanship under normal consumer use for a period of one (1) year from the original purchase date

or thirty (30) days after replacement, whichever occurs later. Genaray’s responsibility with respect

to this limited warranty shall be limited solely to repair or replacement, at Genaray’s discretion, of

any product that fails during normal use of this product in its intended manner and in its intended

environment. Inoperability of the product or part(s) shall be determined by Genaray. If the product

has been discontinued, Genaray reserves the right to replace it with a model of equivalent quality and

function.

This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse,

improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, GENARAY MAKES NEITHER

ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This

warranty provides you with speciﬁc legal rights, and you may also have additional rights that vary from

state to state.

To obtain warranty coverage, contact the Genaray Customer Service Department to obtain a return

merchandise authorization (“RMA”) number, and return the defective product to Genaray along with the

RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk

and expense.

For more information, or to arrange service, visit www.genaray.com or contact us at info@genaray.com.

GG1

Genaray TIR-1X1B User manual

Brand: Genaray

Model: TIR-1X1B

Type: User manual

Download PDF

report

Genaray TIR-1X1B User manual

Genaray TIR-1X1B User manual

Related papers

Other documents