Henny Penny HHC-996 User manual

Henny Penny

Humidified Holding Cabinets

Model HHC-990

Model HHC-992

Model HHC-993

Model HHC-996

Model HHC-997

Model HHC-998

TECHNICAL MANUAL

Model HHC-990/992/993/996/997/998

LIMITED WARRANTY FOR HENNY PENNY APPLIANCES

Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the

original purchaser only for Henny Penny appliances and replacement parts:

NEW EQUIPMENT: Any part of a new appliance, except lamps and fuses, which proves to be defective

in material or workmanship within two (2) years from date of original installation, will be repaired or

replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. To validate this

warranty, the registration card for the appliance must be mailed to Henny Penny within ten (10) days after

installation.

REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be

defective in material or workmanship within ninety (90) days from date of original installation will be

repaired or replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor.

The warranty for new equipment and replacement parts covers only the repair or replacement of the defective

part and does not include any labor charges for the removal and installation of any parts, travel or other expenses

incidental to the repair or replacement of a part.

EXTENDED FRYPOT WARRANTY: Henny Penny will replace any frypot that fails due to manufacturing or

workmanship issues for a period of up to seven (7) years from date of manufacture. This warranty shall not cover

any frypot that fails due to any misuse or abuse, such as heating of the frypot without shortening.

0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship

issues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a

new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.

3 TO 7 YEARS: During this time, any frypot that fails due to manufacturing or workmanship

issues will be replaced at no charge for the frypot only. Any freight charges and labor costs to

install the new frypot as well as the cost of any other parts replaced, such as insulation, thermal

sensors, high limits, fittings, and hardware, will be the responsibility of the owner.

Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased.

No allowance will be granted for repairs made by anyone else without Henny Penny’s written consent. If damage

occurs during shipping, notify the sender at once so that a claim may be filed.

THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY

FOR ANY BREACH OF WARRANTY OR OTHER TERM. BUYER AGREES THAT NO OTHER REMEDY

(INCLUDING CLAIMS FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES) SHALL BE AVAILABLE.

The above limited warranty does not apply (a) to damage resulting from accident, alteration, misuse, or abuse;

(b) if the equipment’s serial number is removed or defaced; or (c) for lamps and fuses. THE ABOVE LIMITED

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUD-

ING MERCHANTABILITY AND FITNESS, AND ALL OTHER WARRANTIES ARE EXCLUDED. HENNY

PENNY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER

OBLIGATION OR LIABILITY.

FM06-005

Revised 10-16-06

Model HHC-990/992/993/996/997/998

TABLE OF CONTENTS

Section Page

Section 1. TROUBLESHOOTING

1-1. Introduction ................................................................................................................. 1-1

1-1. Safety .......................................................................................................................... 1-1

1-3. Troubleshooting .......................................................................................................... 1-1

1-4. Error Codes and Warnings .......................................................................................... 1-5

1-5. Info Mode.................................................................................................................... 1-8

Section 2. LEVEL 2 PROGRAMMING

2-1. Introduction ................................................................................................................. 2-1

2-2. Tech Mode................................................................................................................... 2-1

2-3. Stats Mode................................................................................................................... 2-5

2-4. Data Logging and Manufacturing Mode..................................................................... 2-8

Section 3. MAINTENANCE

3-1. Introduction ................................................................................................................. 3-1

3-2. Maintenance Hints ...................................................................................................... 3-1

3-3. Humidity Sensor Calibration and Replacement.......................................................... 3-1

3-4. Fuse and Fuse Holder Assembly ................................................................................. 3-4

3-5. Power Switch Replacement ........................................................................................ 3-5

3-6. Air Temperature Probe Replacement .......................................................................... 3-6

3-7. Transformer Replacement ........................................................................................... 3-8

3-8. Food Probe Receptacle Replacement.......................................................................... 3-8

3-9. Relay Replacement ..................................................................................................... 3-9

3-10. Module Top Removal.................................................................................................. 3-10

3-11. Cooling Fan Replacement ........................................................................................... 3-11

3-12. High Limit - Air Heater Replacement ......................................................................... 3-11

3-13. Blower Motor Replacement ........................................................................................ 3-12

3-14. Air Heater Replacement.............................................................................................. 3-13

3-15. Speaker Replacement .................................................................................................. 3-13

3-16. Complete Panel or PC Board Replacement ................................................................ 3-14

3-17. Float Switch Replacement .......................................................................................... 3-15

3-18. High Limit - Water Heater Replacement..................................................................... 3-16

3-19. Water Heater Replacement.......................................................................................... 3-17

3-20. Drain Valve Replacement............................................................................................ 3-18

3-21. Door Gasket Replacement .......................................................................................... 3-19

3-22. Vent Motor Replacement ............................................................................................ 3-19

3-23. Vent Motor Microswitch Replacement ....................................................................... 3-20

Wiring Diagrams ......................................................................................................... 3-21

Section 4. PARTS INFORMATION

4-1. Introduction ................................................................................................................. 4-1

4-2. Genuine Parts .............................................................................................................. 4-1

4-3. When Ordering Parts................................................................................................... 4-1

4-4. Prices ........................................................................................................................... 4-1

4-5. Delivery....................................................................................................................... 4-1

4-6. Warranty...................................................................................................................... 4-1

4-7. Recommended Spare Parts for Distributors ............................................................... 4-1

Parts List ..................................................................................................................... 4-2

i 206

Model HHC-990/992/993/996/997/998

This section provides troubleshooting information in the form

of an easy to read table.

If a problem occurs during the first operation of a cabinet,

recheck the installation per the Installation Section of the

Operator’s Manual

Before troubleshooting, always recheck the operation proce-

dures in the Operator’s Manual.

903 1-1

SECTION 1. TROUBLESHOOTING

1-1. INTRODUCTION

1-3. TROUBLESHOOTING

To isolate a malfunction, proceed as follows:

1. Clearly define the problem or symptom and when it occurs.

2. Locate the problem in the troubleshooting table.

3. Review all possible causes. Then, one at a time work through

the list of corrections until problem is solved.

If maintenance procedures are not followed correctly,

injuries and/or property damage could result.

1-2. SAFETY Where information is of particular importance or is safety

related, the words NOTICE, CAUTION, or WARNING are

used. Their usage is described below.

SAFETY ALERT SYMBOL is used with DANGER,

WARNING, or CAUTION which indicates a personal

injury type hazard.

NOTICE is used to highlight especially important

information.

CAUTION used without the safety alert symbol indicates

a potentially hazardous situation which, if not avoided,

may result in property damage.

CAUTION used with the safety alert symbol indicates a

potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

Model HHC-990/992/993/996/997/998

1-3. TROUBLESHOOTING (continued)

Problem Cause Correction

OPERATION

A. Product not • Doors left open • Keep doors closed except

holding temperature to load and serve product

• Product held too long • Hold product only for recom-

mended times

• Control temperature set too low • Increase air temperature

setpoint

(SP-3) in Special Program Mode

• Bad air heater • Check heaters and replace if bad

See Tech Mode items 10 and 18

• Blower not working • Check blower and replace if bad

See Tech Mode item 20

• Bad air heater, or blower relays • Replace relay

See Tech Mode items 10 and 18

• Bad high limit • Check high limit and replace if

bad

• Low or improper voltage • Compare receptacle voltage to

data plate voltage

• Door gasket torn or worn • Replace bad door gaskets

• Air probe faulty, open (“E-6A”), • Ohm out the probe and replace

or shorted (“E-6B”) if necessary

B. Cabinet steaming • Humidity setpoint too high • Decrease humidity setpoint

or product soggy (SP-4) in Special Program Mode

• Water heater probe faulty, open • Ohm out the probe and replace

(“E-12A”), or closed (“E-12B”) if necessary

• Bad humidity sensor (“E17”) • Replace humidity sensor

• Relay stuck closed • Replace relay

• Vent stuck closed (“E-80”) • Bad vent motor - replace

• Bad vent motor relay - replace-

See Tech Mode item 20

• Check alignment and condition

of mechanical vent parts

1-2 903

Model HHC-990/992/993/996/997/998

OPERATION (Continued)

C. Product dry • Bad float switch (“E-18”) • Replace float switch

• Bad water heater high limit • Replace high limit

• Bad water heater • Check heater and replace if bad;

see Tech Mode item 20

• Humidity setpoint too low • Increase humidity setpoint

(SP-4) in Special Program Mode

• No water in pan • Pour water in water pan

• Vent stuck open (“E-80”) • Bad vent motor - replace; see

Tech Mode item 20

• Bad vent motor relay - replace

• Check alignment and condition

of mechanical vent parts

HEATING SYSTEM

A. Unit not heating • Bad control board • Replace control board

• Bad high limit • Check high limit; replace if bad

• Bad air heater or blower relays • Replace relay

• Bad air heater • Check heaters and replace if bad;

see Tech Mode item 20

• Faulty wiring • Check for loose connections or

broken wires

• Blown Fuse • Change 15 amp fuse

B. Unit not reaching set • Blower not working. • Check Blower and replace if bad;

temperature see Tech Mode item 20

• Bad air heater • Check heaters and replace if bad;

see Tech Mode item 20

• Bad air heater, or blower relays • Replace relay

• Doors left open • Keep doors closed except

to load and serve product

• Door gasket torn or worn • Replace bad door gaskets

1-3. TROUBLESHOOTING (continued)

Problem Cause Correction

903 1-3

Model HHC-990/992/993/996/997/998

C. Unit Overheating • Blower not working • Check blower and replace if bad

(“E-5”) See Tech Mode item 20

• Bad control board • Replace control board

• Relay stuck closed • Replace relay

1-3. TROUBLESHOOTING (continued)

Problem Cause Correction

HEATING SYSTEM (Continued)

1-4 903

Model HHC-990/992/993/996/997/998

804 1-5

1-4. ERROR CODES AND The display shows the following error codes and warnings when a

WARNINGS fault is detected, along with an alarm sound. Both the heat and

humidity systems shut down, except when specified otherwise.

Display Cause Panel Board Correction

“E-4 CPU TOO HOT” • Control board too hot;

unit overheating or

louvers clogged

“E-5 AIR TEMP TOO HOT” • Faulty relay, PC board,

or air probe

“E-54A CPU TEMP SENSOR • Faulty PC board

OPEN”

“E-54B CPU TEMP SENSOR • Faulty PC board

SHORTED”

“E-6A AIR TEMP SENSOR • Faulty air probe

FAILED OPEN”

• Turn switch to OFF position, then back to

ON; if display still shows “E-4”, the PC

board is getting too hot; clean louvers and

check cooling fan; if cooling fan is not

working, have it replaced; once panel

cools down, the controls should return to

normal; if “E-4” persists, have the PC

board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-5”, the heating

circuits and temperature probe should be

checked; once the unit cools down, the

controls should return to normal; if “E-5”

persists, have the PC board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-54A”, the

control should be re-initialized (see Pro-

gramming Section); if the error code

persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-54B”, the

control should be re-initialized (see Pro-

gramming Section); if the error code

persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-6”, the

temperature probe should be checked;

once the temperature probe is repaired, or

replaced, the controls should return to

normal; if “E-6” persists, have the PC

board replaced

Model HHC-990/992/993/996/997/998

“E-6B AIR TEMP SENSOR • Faulty air temperature

FAILED SHORTED” probe

“E-12A WATER HEATER • Faulty water

SENSOR FAILED heater probe

OPEN”

“E-12B WATER HEATER • Faulty water

SENSOR FAILED heater probe

CLOSED”

“E-17 HUMIDITY SENSOR • Faulty humidity sensor

FAILED”

“E-18 NO WATER, FLOAT • Float switch stuck or

SWITCH FAILED” faulty; faulty relay

(stuck on);water pan

needs cleaned;

loose or faulty water

heater sensor; acorn nuts

on water heater cover

loose, or water heater

insulation missing or

damaged

A humidity error only shuts down the humidity system. If a humidity error occurs, and you want to

use the cabinet without humidity, turn the humidity off by following the directions for SP-4, Humidity

Setpoint, in Special Programming Section of this manual. Once the setpoint is off, the alarm stops,

but the error code shows in display. (Includes “E-12A”, “E-12B”, “E-17” and “E-18”).

1-4. ERROR CODES AND

WARNINGS (Continued)

Display Cause Panel Board Correction

• Turn switch to OFF position, then back to

ON; if the display shows “E-6”, the

temperature probe should be checked;

once the temperature probe is repaired, or

replaced, the controls should return to

normal; if “E-6”persists, have PC board

replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-12A”, the

water heater should be checked and

repaired or replaced (the water heater

probe is built into the water heater); the

controls should return to normal; if

“E-12A” persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-12B”, the

water heater should be checked and

repaired or replaced (the water heater

probe is built into the water heater); the

controls should return to normal; if

“E-12B” persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-17”, the

humidity sensor should be checked;

once the humidity sensor is repaired, or

replaced, the controls should return to

normal; if “E-17” persists, have PC board

replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-18”, check

and clean float switch; clean water pan;

have relay and water heater sensor

checked and replace if necessary; tighten

acorn nuts on water heater cover; make

sure 2 complete pieces of insulation are

under the water heater cover; if “E-18”

persists, have PC board replaced

1-6 804

Model HHC-990/992/993/996/997/998

1-4. ERROR CODES AND

WARNINGS (Continued)

“E-41 SYSTEM DATA LOST” • Memory scrambled

“E-46 DATA SAVE FAILED” • Memory scrambled

“E-80 VENT STUCK OR • Vent on rear of module

BAD SWITCH” stuck or faulty vent

activation switch

“PLEASE DE-LIME • Water pan needs

WATER PAN” cleaned

“WATER LEVEL LOW, PLEASE” • Water pan low on water

or empty

804 1-7

• Turn switch to OFF position, then back to

ON; if the display shows “E-41”, the

control should be re-initialized (see Pro-

gramming Section); if “E-41”persists, have

PC board replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-46”, the

control should be re-initialized (see Pro-

gramming Section); if “E-46”persists, have

PC board replaced

• Check vent on rear of module for obstruc-

tions, or have vent activation switch

replaced

• Follow the weekly cleaning procedures;

this warning will

not shut down the heat

or humidity; if “PLEASE DE-LIME

WATER PAN” persists, have PC board

replaced

• Fill water pan, in bottom of unit, to the

maximum water fill mark; this warning

won’t shut down the heat or humidity

Display Cause Panel Board Correction

Model HHC-990/992/993/996/997/998

1-5. INFO MODE This mode records historic information on the holding cabinet

and operator performance, which could help in troubleshooting

a problem.

This mode records historic information on the unit and operator

performance. Press and at the same time and

“*INFO MODE*” shows on display. Press or to

access the steps and press to view the statistics within

each step.

Information Mode is intended for technical use, but the opera-

tor can view the following information:

1. Error Log - last 10 errors and time they occurred

2. Power Up Log - time of last 10 power-ups

3. Outputs/Inputs - shows the state of unit’s inputs and

outputs

a. OUT V_F_W_A (vent motor, fan, water heater, air

heater, relay order from left to right)

b. AMPS V_F_W_A_

c. NC/GD V_F_W_A_ (no connect/ground detection on

outputs to relays)

d. All outputs and inputs V_F_W_A_ P_ (power switch

input) E_(exhaust vent switch input) F_ (float switch

input)

4. Vent - open or closed

5. CPU temperature

6. Cabinet air temperature

7. Water heater temperature

8. Food probe temperature

9. Humidity counts value

10. Humidity value

11. Analog inputs

1-8 906

Model HHC-990/992/993/996/997/998

1. E-LOG (error code log)

Press and “1A. (date & time) *NOW*” shows in display.

This is the present date and time.

Press and if a error was recorded, “1B. (date, time, and

error code information)” shows in display. This is the latest

error code that the controls recorded.

Press and the next latest error code information can be

seen. Up to 10 error codes (1B to 1K) can be stored in the E-

LOG section.

Press to continue to P-LOG.

2. P-LOG (power-up log)

Press and “2A. (date & time) *NOW*” shows in display.

This is the present date and time.

Press and the latest power-up is shown, “2B. (date, time,)

PWR-UP”.

Press and the next latest power-up date is shown. Up

to 10 power-ups (2B to 2K) can be stored in the P-LOG

section.

Press to continue onto the Outputs/Inputs.

3. OUTPUTS/INPUTS

This mode displays the status of components and inputs. If the

input or output signal is detected, an identifying letter is

displayed (see below). If the signal is not detected, “_” is

displayed. Press to view the following:

a. “V_F_W_A_” shows in the display. If the output is on,

“*” shows beside the output letter. Ex: “V*”. If the

control senses a problem with the output, “*” flashes.

b. “AMPS V_F_W_A_” shows in the display. A

checkmark (“√” ) beside the letter indicates normal amps .

A flashing “X” beside the letter means a problem exists.

c. “NC/GD V_F_W_A_” shows in the display. This

monitors a possible problem with the relays on the output

PC board. A checkmark (“√” ) beside the letter indicates

means everything on the output PC board is good. A

flashing “X” beside the letter means a problem exists.

1-5. INFO MODE (Continued)

903 1-9

Model HHC-990/992/993/996/997/998

1-5. INFO MODE (Continued) 3. OUTPUTS/INPUTS (Continued)

d. V_F_W_A_ P_E_F_ shows in the display. If the output

or input signal is detected, “*” shows beside the letter. Ex:

“V*”. If the control senses a problem with the output, “*”

flashes.

Press to continue onto VENT.

4. VENT

This indicates whether the vent is open or closed.

Press to continue onto CPU TMP.

5. CPU TMP

This step shows the present PC board temperature.

Press to continue onto the Cabinet Air TMP.

6. CABINET AIR TMP

This step shows the present air temperature inside the cabinet.

Press to continue onto the Water Heater TMP.

7. WATER HEATER TMP

This step shows the present water heater temperature.

Press to continue to Food TMP.

8. FOOD TMP

This step shows the present food probe temperature, if used.

Press to continue onto Humidity Counts Value.

9. HUMIDITY COUNTS VALUE

Factory use only!

Press to continue onto the Humidity Value.

10. HUMIDITY VALUE

This step shows the present humidity level inside the cabinet.

Press to continue onto the Analog Inputs.

1-10 903

Model HHC-990/992/993/996/997/998

1-5. INFO MODE (Continued) 11. ANALOG INPUTS (Continued)

This step displays the present status of any channel of the controller’s a

to d converter. This feature may be useful to a technician

troubleshooting a problem with the controller.

The displayed value can be toggled between volts and bits by

pressing . If the displayed value has a decimal point, it is

voltage (0 to 5 VDC). If no decimal point is shown, the value is

a-to-d bits (0 - 4095).

903 1-11

Model HHC-990/992/993/996/997/998

The Tech Mode and Stats Mode in the Level 2 Programming,

have information that could help in troubleshooting a problem

with the unit.

Press and hold until “L-2 LEVEL 2”, followed by,

“CLOCK SET”, shows in display.

Press 3 times and “TECH”, followed by, “ENTER CODE”

shows in display.

Enter code, to access

the following items:

T-1 Software

T-2 Cabinet version

T-3 Push button test

T-4 All on display test

T-5 Segments test

T-6 Digits test

T-7 Decimal points test

T-8 LED test

T-9 Air temperature - circuit calibration

T-10 Air temperature - user calibration/offset/highest value

T-11 Water heater temperature - circuit calibration

T-12 Water heater temperature - user calibration/offset/highest

value

T-13 Food temperature - circuit calibration

T-14 Food temperature - user calibration/offset/highest value

T-15 Humidity - circuit calibration

T-16 Humidity sensor – calibration/offset; specific value sent

with each humidity sensor

T-17 Humidity- user calibration/offset/highest value

T-18 CPU° - control temperature - highest value

T-19 View ADC channel

T-20 Outputs/Inputs; on outputs steps use the following

hidden buttons [1-4] to toggle on the outputs; [1] - vent

motor [2] - circulation fan, [3] - water heater, [4] - air

heater

T-21 Total init – initialization of programming areas and

statistics

moves you forward through the above selections and

moves you backwards through the selections.

903 2-1

2-2. TECH MODE

SECTION 2. LEVEL 2 PROGRAMMING

2-1. INTRODUCTION

Model HHC-990/992/993/996/997/998

T-1: Software

This section shows “PN/ID/SRL”

Press . Henny Penny EPROM part number is displayed.

Press . Customer ID (i.e. Wendy’s) is displayed

Press . Software revision is displayed.

T-2: Cabinet Version

This section shows the model number, e.i. HHC-993.

T3: Push Button Test

Press any button on the control and a digital display feedback

confirms the button is working.

T4: All On Display Test

Press any of the product buttons and every LED on the 16 digit

display lights.

T5: Segments Test

Repeatedly pressing any product button lights one segments in

every one of the 16 digit displays.

T6: Digits Test

Repeatedly pressing any product button lights all segments in

one of the 16 digital displays. (Scrolls though all 16.)

T7: Decimal Point Test

Repeatedly pressing any product button lights a decimal point

(DP) in one of the 16 digital displays. (Scrolls though all 16.)

T8: LED Test

Repeatedly pressing any product button lights individual

LEDs. (Scrolls though all LEDs.)

T9: Air Temperature - Circuit Calibration

Factory use.

2-2. TECH MODE (Continued)

2-2 903

Model HHC-990/992/993/996/997/998

T10: Air Temperature - Calibration/Offset/Highest

This is a user calibration to make sure the display shows the

actual air temperature.

Press and hold and use to set the display to

match the actual temperature. (+/-15

o

F)

Press and hold to change the amount of the offset.(+/-15

o

F)

Press and hold to view the highest air temperature recorded.

Press to reset highest temperature.

T11: Water Heater Temperature - Circuit Calibration

Factory use.

T12: Water Heater Temperature - Calibration/Offset/

Highest

This is a user calibration to make sure the display shows the

actual water heater temperature.

Press and hold and use to set the display to

match the actual temperature. (+/-15

o

F)

Press and hold to change the amount of the offset.(+/-15

o

F)

Press and hold to view the highest air temperature recorded.

Press to reset highest temperature.

T13: Food Probe Temperature - Circuit Calibration

Factory use.

T14: Food Probe Temperature - Calibration/Offset/Highest

This is a user calibration to make sure the display shows the

actual food temperature, when using the food probe.

Press and hold and use to set the display to

match the actual temperature. (+/-15

o

F)

Press and hold to change the amount of the offset.(+/-15

o

F)

Press and hold to view the highest air temperature recorded.

Press to reset highest temperature.

2-2. TECH MODE (Continued)

903 2-3

Model HHC-990/992/993/996/997/998

2-2. TECH MODE (Continued) T15: Humidity - Circuit Calibration

See Section 3-3 on Humidity Sensor Calibration and

Replacement.

T16: Humidity Sensor - Calibration/Offset

This is a specific value that is sent with the humidity sensor,

when necessary. Otherwise, this value should be 0.

T17: Humidity - Calibration/Offset/Highest

This is a user calibration to make sure the display shows the

actual humidity inside the cabinet.

Press and hold and use to set the display to

match the actual humidity. (0 to 100%)

Press and hold to change the amount of the offset.(-0 to -99)

Press and hold to view the highest humidity recorded.

Press to reset highest humidity.

T18: CPU

o

- Control Temperature - Highest Value

This shows the highest temperature the control board was

exposed to.

T19: View ADC Channel

Factory use.

T20: Outputs/Inputs

The following components can be tested:

toggles the vent motor off and on.

toggles the cooling fan off and on.

toggles the water heater off and on.

toggles the air heaters off and on.

T21: Total Initialization

This completely resets any accumulated information and

changed settings in the controls. Contact Henny Penny before

completing this step.

2-4 705

Page is loading ...

Henny Penny HHC-996 User manual

This manual is also suitable for

Henny Penny HHC-996 User manual

Related papers

Other documents