Playskool Dream Town Sweet Lily Castle User manual

This Castle meets the

ammability requirements of

CPAI-84. The fabric may burn

if left in continuous contact

with any ame source. The

application of any foreign

substance to the Castle fabric

may render the ame resistant

properties ineective.

KEEP ALL FLAME

AND HEAT SOURCES

AWAY FROM THE

SWEET LILY

TM

CASTLE

FABRIC.

WARNING:

Adult assembly

required.

Thanks for

purchasing the

SWEET LILY

TM

Castle.

Please read and retain

these instructions.

AGES 3+

68779

For video assembly instructions, please visit

www.mysweetlilycastle.com

Includes:

41x Connectors

30x White Frame Tubes

2 Fabric Castle Covers

Also includes:

1 princess dress

(ts sizes 3T to 6X)

1 tiara

1 wand

1 frog prince

1

BACK

FRONT

4x Grey Plastic Tubes

26x Pink Frame Tubes

Front side

Back side

2 x

#1

2 x

#1

1x Green Plastic Tube

2 x Grey Plastic Connectors

4 x front bottom connectors (red)

4 x back corner connectors (red)

11 x straight connectors (white)

6 x tee connectors (yellow)

4 x roof corner X connectors (green)

4 x hip corner top connectors (blue)

4 x roof corner Y connectors (orange)

2 x

#10

2 x

#9

2 x

#8

2 x

#7

2 x

#6

2 x

#5

12 x

#4

2 x

#3

2 x

#2

4 x hip corner base connectors (blue)

2 x

#2

10 x

#3

2 x

#4

2 x

#5

2 x

#6

2 x

#7

2 x

#8

2 x

#9

Front

Frame

Assembly:

Assemble Front frame as shown.

This will be done in Three steps:

1.

Start with the base—just like building a normal house.

2.

Build the castle walls—add all the

vertical tubes with the connectors

on the top. Add tubes for the top

of the walls.

3.

Build the roof—add the tubes and

connectors, as shown.

The roof will

create a four-sided peak.

Parts required

for this step:

- All connectors

- All white frame tubes

Make sure

connectors are

pushed into the

tubes as far as they

will go.

2

#4

#8

#7

#9

#10

#6

#3

#6

#5

#1

#2

#3

#2

#1

#8

#10

Assemble Front frame as shown.

3.

Build the roof—add the tubes and

connectors, as shown.

The roof will

create a four-sided peak.

Back

Frame

Assembly:

Assemble Back frame as shown.

Parts required

for this step:

- Remaining connectors

- All pink frame tubes

Make sure

connectors are

pushed into the

tubes as far as

they will go.

3

This will be done in Three steps:

1.

Start with the base—just like building a normal house.

2.

Build the castle walls—add all the

vertical tubes with the connectors on

the top. Add tubes for the top of

the walls.

3.

Build the roof—add the tubes and

connectors, as shown. The roof will

create a four-sided peak.

#1

#2

#3

#5

#4

#9

#7

#6

#7

#8

#9

Castle

Back

Cover:

4

Parts required

for this step:

- Completed Frame (pink)

- SWEET LILY

Castle Back

SWEET LILY Castle Back Cover

1.

Assemble pink frame as shown on page 3.

2.

Remove the SWEET LILY Castle back cover

from the bag marked “Back.”

3.

Completely unzip the cover all the way

around.

4.

Separate the inside and outside walls

by pulling apart the hook-and-loop

fasteners (don’t forget

the windows!).

6.

Line up the frame on the red seam

as shown.

5.

Lay the cover out so both the rectangular

red seam and lavender wall face up.

BACK

5

7.

Lift the inside wall up and attach it to the frame

with the hook-and-loop fasteners.

8.

Pull out any excess cover from the outside corners of the frame base to make a snug pocket.

Pull the cover over the closed end of the frame and across the top of the roof (you may need a helper).

The zipper strip should align with the frame.

17x

fasteners

Make sure the bottoms of the

strips line up with the bottoms of

the pads.

6

9.

Zip up the cover around the frame. Press the three hook-and-loop fasteners along inside the cover at

the top of the frame to keep the roof from sagging.

10.

Align and fasten the hook-and-loop fastener around

both windows.

The back of the castle is now

complete. Let’s do the front!

Castle

Front

Cover:

Parts required

for this step:

- Completed Frame (white)

- SWEET LILY

Castle Front

SWEET LILY Castle Front Cover

1.

Assemble white frame as shown on page 2.

2.

Remove the SWEET LILY Castle front cover

from the bag marked “Front”.

3.

Completely unzip the cover all

the way around.

5.

Separate the inside and outside walls

by pulling apart the hook-and-loop

fasteners.

6.

Lay the cover so the rectangular red seam

is exposed. The pink inside wall is over the

the printed oor. The doors should

be tucked under the oor.

7

FRONT

4.

Unzip the front doors.

6.

Line up the frame on the red seam, as shown.

7.

Lift the inside wall up and attach it to the frame

with the hook-and-loop fasteners.

16x

fasteners

Make sure the bottoms of the

strips line up with the bottoms

of the pads.

8

8.

Pull out any excess cover from the outside corners of the frame base to make a snug pocket.

Pull the cover with the doors over the closed end of the frame and across the roof

(you may need a helper). The zipper strip should align with the frame.

9.

Zip up cover around the frame. Press the three hook-and-loop fasteners along inside the cover

at the top of the frame to keep the roof from sagging.

9

10

10.

Fasten the two wide hook-and-loop fasteners around the vertical tubes on both sides of the door.

Zip up the door.

11.

Unhook the fasteners in the roof turret. Raise the turret by bending the green plastic tube to

t inside. The at end ts in the middle of the center disk at the bottom and the cone-shaped

end faces up.

The front of the

castle is now

complete. Let’s build

the towers!

Questions? Call 1-800-PLAYSKL

Product and colors may vary.

TM & ® denote U.S. Trademarks.

Tower

Assembly:

Storage:

For the entire

Dream Town

TM

Collection

1.

Take two grey tubes and one

connector. Insert a tube into each

end of connector.

2.

Open the hook-and-eye fasteners in the

tower.

Insert one end of the tube into

the tower up to the the point. Fit the

bottom of the plastic tube into the

middle of the center disk in the

tower oor.

3.

Reclose the tower and attach it

to the hook-and-loop fasteners

at the front corners of the

castle. The windows

face out. Repeat

Steps 1,2 and 3 for

the second tower.

Parts required

for this step:

- 2 Tower covers

- 4 Grey plastic tubes

- 2 Grey plastic connectors

Playskool Dream Town Sweet Lily Castle User manual

This manual is also suitable for

Playskool Dream Town Sweet Lily Castle User manual

Related papers

Other documents