ESP EM2WMEXSIGN User manual

Brand: ESP

Model: EM2WMEXSIGN

Type: User manual

www.espuk.com

EM2W NM & M EXIT SIGN

EMERGENCY LIGHTING LUMINAIRE

INSTRUCTIONS AND TEST PROCEDURES

Month Test Sign Date Sign Date Sign Date Sign Date Sign Date

1 Functional

2 Functional

3 Functional

4 Functional

5 Functional

6 1 hour

7 Functional

8 Functional

9 Functional

10 Functional

11 Functional

1 Hour

3 Hour

1st year 2nd Year 3rd Year 4th Year 5th year

T: +44 (0)1527 51 51 50 F: +44 (0)1527 51 51 43

E: [email protected]

TECHNICAL PARAMETER

Batteries installed or replaced: Nicd 4.8V 600mAH

Supply Voltage: 220-240V/50/60Hz

Charging Current: 85-90mAH

Charging Duration: 24 Hours

Batteries Protection: Overcharge and full discharge

Discharge Duration: more than 3 Hours

Lamp Source: High Power White LED

Max Intensity: 6100Mcd

Operation Indicator: Charge LED

Proration Rating: IP20

Operation Temperature: 0 - 60 Degrees C

Humidity: up to 95% Relative Humidity

Dimensions: 380 x 195 x 51mm

Weight: 1350g

Luminaire Type/Ref: Date of Installation: Location:

EM2W NM & M EXIT SIGN INSTRUCTIONS.indd 2-3 27/03/2014 09:16:44

INDICATION LED STATUE

Charge Green LED (RIGHT): ON: Power supply an full charge

OFF: Power supply fails

TEST BUTTON

Press the test button next to the Led indicator.

That would be AC supply switch to the DC supply.

IMPORTANT

Ensure the mains supply is isolated before undertaking any electrical

installation of product. Disconnect luminaires from the supply when

carrying out megger testing. Installation should be carried out by a qualied

electrician in accordance with the relevant IEE Wiring Regulations.

INSTALLATION

In order for the luminaire to become operational, the battery and the mains

power supply must be connected. An internal terminal block is used to

connect the luminaire to the mains power supply. To obtain access to this

terminal block and to the battery remove the cover of the main body by

unscrewing the two retaining screws, the connection socket arrangement

ensuring correct polarity. Determine the length of wire suspension required

and if necessary will permit the wire to be adjusted accordingly. When

required length is achieved re-lock mechanism, To avoid excess wire inside

the unit, wire can be cut to desired length and re-terminated on the pcb

thus ensuring no wire comes into contact with any other connections on the

pcb. Failure to ensure no excess wire inside the unit causing subsequent

damage will invalidate the warranty. Unit can then be re-assembled and

secured with the 2 retaining screws previously removed.

MOUNTING OF LUMINAIRE

This lamp can be wall mounted and ceiling mounted.

RECOMMENDED ROUTINE TEST PROCEDURE

The following test is designed to ensure the continued protection of your

premises and occupants. Because of the possibility of a failure of the

normal lighting supply occurring shortly after a period of testing, all tests

should whenever possible, be undertaken at times of least risk, e.g during

daylight hours.

ONCE A DAY

Visual inspection of battery charge led.

ONCE A MONTH

Each unit should be energised from its battery for about 30 seconds by

simulation of a failure of the normal lighting supply, to ensure the lamp

operates in the emergency condition.

TWICE A YEAR

Each unit should be energized from its battery for a continuous period of at

least one hour. Inspect the uorescent tube and if the ends are blackened

replace. It is recommended that for maintained luminaires the tubes are

replaced at intervals of no more than 1 year in order to retain the design

photometric characteristics.

AFTER THREE YEARS & EACH SUBSEQUENT YEAR

All units with specied durations in excess of 1 hour should be energised

for their full rating period.

TECHNICAL PARAMETER

Supply Voltage: 220-240V/50/60Hz

Bat

ries installed or replaced: Ni-cd 4.8V 600mah

Charging current:85-90mah

Charging duration: 24 hours

Discharging duration: more than 3 hours

Batteries protection: Overcharge and full discharge

Lamp source: High power white LED

Max Intensity: 6100mcd

Operation Indicator: Charge LED

Proration rating: IP20

Operation Temperature: 0 - 60 degrees C

Humidity: Up to 95% relative humidity

Dimensiions: 380 x 195 x 51 mm

Weight: 1350g

Indication LED Statue:

Charge Green LED (RIGHT):

ON: Power supply and full charge

Off: Power supply fails

Important:

Ensure the mains supply is isolated before undertaking any

electrical installation of product. Disconnect luminaries from

the supply when carrying out megger testing. Installation

should be carried out by a qualified electrician in accordance

with the relevant IEE Wiring Regulations.

Installation

In order for the luminaire to become operational, the battery

and the mains power supply must be connected. An internal

terminal block is usd to connect the luminaire to the mains

power supply. To obtain assess to this terminal block and to

the battery remove the cover of the main body by unscrewing

the two retining screws, The connection socket arrangement

ensuring correct polarity. Determine the length of wire

suspension required and if necessary will permit the wire to

be adjusted according ly. W

hen required length is achieved

re-lock mechanism. To avoid excess wire inside the unit, wire

can be cut to desired length and re-terminated on the pcb thus

ensuring no wire comes into contact with any other connections

on the pcb. Failure to ensure no e xcess wire inside the unit

causing subsequent damage will invalidate the warranty. Unit

can then be re-assembled and secured with the 2 retaining

screws previously removed.

terminal block

Connection

230V AC

Mounting of Luminaire

This lamp can be wall mounted and ceiling mounted.

Test button

Press the test button next to the Led indicator.

That would be AC supply switch to the DC supply.

EM2W NM & M EXIT SIGN INSTRUCTIONS.indd 4-5 27/03/2014 09:16:45

ESP EM2WMEXSIGN User manual

ESP EM2WMEXSIGN User manual

ESP EM2WMEXSIGN User manual

Related papers

Other documents