KidKraft Abbeydale Clubhouse Wooden Playset Assembly Instruction

Table of Contents

Warnings and Safe Play Instrucons .......... pg. 2

Protecve Surfacing Guidelines .............. pg. 3

Instrucons for Proper Maintenance ......... pg. 4

About Our Wood – Limited Warranty ......... pg. 5

Keys to Assembly Success ................... pg. 6

Metric Conversion Sheets ..................pg. 7,8

Part ID .................................... pg. 9

Step by Step Instrucon ....................pg. 20

Installaon of I.D./Warning Plaque .......Final Step

9403920X

INSTALLATION AND OPERATING INSTRUCTIONS

10-14 Hrs

ABBEYDALE CLUBHOUSE–F23920X

Abbeydale Clubhouse X

H: 10ft -6"

17'-6"

7'-6"

30'-6"

26'-0"

To reduce the risk of serious injury or death, you must read and

follow these instrucons. Keep and refer to these instrucons

oen and give them to any future owner of this play system. Manufacturer contact informaon provided

below.

OBSTACLE FREE SAFETY ZONE - 30’6” x 26’ area requires Protecve Surfacing. See page 3.

MAXIMUM VERTICAL FALL HEIGHT - 7’-0”

CAPACITY - 12 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.

RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares

or parks.

Warning. Only for domesc use.

WARNING

TWO PERSON

ASSEMBLY

Playset Dimensions:

L: 17ft -6” x W: 7ft -6”

Obstacle Free Safey Zone:

L: 30ft -6” x W: 26ft -0”

Rev 06/21/2019

KidKraft, Inc.

4630 Olin Road

Dallas, Texas 75244 USA

[email protected]

1.800.933.0771

972.385.0100

For online parts replacement visit

https://parts.kidkraft.com/

KidKraft Netherlands BV

Olympisch Stadion 29

1076DE Amsterdam

The Netherlands

[email protected]

+31 20 305 8620 M-F from 09:00 to 17:30

(GMT+1)

For online parts replacement visit

https://parts.kidkraft.eu/

Warnings and Safe Play Instructions

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred

while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying

with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using

this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they

understand and follow them. Remember on-site adult supervision is required for children of all ages.

SERIOUS HEAD INJURY HAZARD

Installation over concrete, asphalt, dirt, grass, carpet

and other hard surface creates a risk of serious injury

or death from falls to the ground. Install and maintain

shock absorbing material under and around play-set as

recommended on page 3 of these instructions.

COLLISION HAZARD

Place play-set on level ground at least 2m from any

obstruction such as a garage or house, fences, poles,

trees, sidewalks, walls, landscape timbers, rocks,

pavement, planters, garden borders, overhanging

branches, laundry lines, and electrical wires. (See

OBSTAC

LE FREE SAFETY ZONE on cover)

CHOKING HAZARD/SHARP EDGES & POINTS

Adult assembly required. This product contains small

parts and parts with sharp edges and points. Keep parts

away from children until fully assembled.

WARNING LABEL

Owners shall be responsible for maintaining the legibility

of the warning labels.

STRANGULATION HAZARD

,seni lsehtolc ,sepor ht iw yalp ot nerdl ihc wol la REVEN •

pet leashes, cables, chains or cord-like items when using

this play-set or to attach these items to play-set.

ponchos, hoods, scarves, capes, necklaces, items with

draw-strings, cords or ties when using this play-set.

ste mleh trops ro ekib raew ot nerdl ihc wol la REVEN •

when using this play-set.

Failure to prohibit these items, even helmets with chin

straps, increases the risk of serious injury and death to

children from entanglement and strangulation.

TIP OVER HAZARD

Choose a level location for the equipment. This can reduce

the likelihood of the play set tipping over and loose-ﬁll

surfacing materials washing away during heavy rains.

DO NOT allow children to play on the play-set until the

assembly is complete and the unit is properly anchored.

Never add extra length to chain or rope. The chains or ropes

provided are the maximum length designed for the swinging

element(s).

WARNING

eeS . t es-ya l p ruoy fo sno i t a t imi l y t i capac evr esbO

front cover.

gn i so l cne t oo f l l u f dna gn i t t ﬁ l l ew h t iw ne r d l i hc sse rD

footwear.

retnec eht ni thgiew l luf r ieht ht iw t i s ot nerdl ihc hcaeT

of the swing seat to prevent erratic swing motion or

falling off.

, gn i ss im ; doo w dekcarc ro nekorb , dere tn i l ps rof kcehC

loose, or sharp edged hardware. Replace, tighten and or

sand smooth as required prior to playing.

n i ahc , s r edda l epor , sepo r gn i bmi l c dednepsus t ah t y f i r eV

or cable are secured at both ends and cannot be looped

back on itself as to create an entanglement hazard.

r eh t o dna ed i l s eh t kcehc , syad t oh ro dna ynnus nO

plastic rides to assure that they are not very hot as to

cause burns. Cool hot slide and rides with water and wipe

dry prior to using.

r aewt oo f l eeh ro eo t nepo r aew o t ne rd l i hc wo l l a t on oD

like sandals, ﬂip–ﬂops or clogs.

dniheb ,neewteb , tnorf ni ,klaw ot nerdl ihc wol la ton oD

or close to moving rides.

pool ro sepor ro sniahc gniws tsiwt nerdl ihc tel ton oD

them over the top support bar. This may reduce the

strength of the chain or rope and cause premature failure.

.noi tom ni era yeht el ihw sedi r f fo teg nerdl ihc tel ton oD

. t ew s i t i nehw t nemp i uqe no gn i bmi l c t imr ep t on oD

a n i t nem p i uqe f o esu r o ya l p hguo r t imr ep t on oD

manner for which it was not intended. Standing on or

jumping from the roof, elevated platforms, swings,

climbers, ladders or slide can be dangerous.

.staes ro sedi r ytp m e gniws ot nerdl ihc wol la ton oD

ro t srﬁ daeh ed i l s nwod og o t ne rd l i hc wo l l a t on oD

run up slide.

WARNING

– Safe Play Instructions

Orientate slide such that it gets the least amount of exposure

to the sun.

2

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing

protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable

for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever

product you select, follow these guidelines:

Loose-Fill Materials

• Maintain a minimum depth of 9 inches of loose-ﬁll materials such as wood mulch/chips, engineered wood ﬁber (EWF), or

shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet

high. NOTE: An initial ﬁll level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also

compact, displace, and settle, and should be periodically raked and reﬁlled to maintain at least a 9-inch depth.

• Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this

should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)

NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface

can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and

environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective

surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play

surface -- does not need any protective surfacing.

• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to

account for water drainage.

• Periodically rake, check and maintain the depth of the loose-ﬁll surfacing material. Marking the correct depth on the play

equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to

rake and evenly redistribute the surfacing in heavily used areas.

• Do not install loose ﬁll surfacing over hard surfaces such as concrete or asphalt.

Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles

You may be interested in using surfacing other than loose-ﬁll materials - like rubber tiles or poured-in-place surfaces.

• Installations of these surfaces generally require a professional and are not “do-it yourself” projects.

• Review surface speciﬁcations before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that

the product has been tested to the following safety standard: ASTM F1292 Standard Speciﬁcation for Impact Attenuation of

Surfacing Materials within the Use Zone of Playground Equipment. This report should show the speciﬁc height for which the

surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical

distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing

below - of your play equipment.

• Check the protective surfacing frequently for wear.

Placement

Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to;

• Extend surfacing at least 2m from the equipment in all directions.

• For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar

from which the swing is suspended.

• For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all

directions.

From the CPSC Outdoor Home Playground Safety Handbook. At http://www.playgroundregs.com/resources/CPSC%20324.pdf

Protective Surfacing - Reducing Risk of Serious Head Injury From Falls.

2H 2H

H

Denotes Use Zone with Protective Surfacing

Use Zone for Single-Axis Swings

6 ft.

Denotes Use Zone with Protective Surfacing

Use Zone for Multi-Axis Swings

6 ft. 6 ft.

6 ft.

L

3

Instructions for Proper Maintenance

HARDWARE:

Check metal parts for rust. If found,

sand and repaint using a non-lead

paint complying with 16 CFR 1303.

Inspect and tighten all hardware. On

wood assemblies DO NOT OVER-

TIGHTEN as to cause crushing and

splintering of wood.

Check for sharp edges or protruding screw threads, add

washers if required.

SHOCK ABSORBING SURFACING:

Check for foreign objects. Rake and check depth of loose

ﬁll protective surfacing materials to prevent compaction

and maintain appropriate depth. Replace as necessary.

(See Protective Surfacing, page 3)

GROUND STAKES (ANCHORS):

Check for looseness, damage or deterioration. Should

ﬁrmly anchor unit to ground during use. Re-secure and

or replace, if necessary.

SWING HANGERS:

Check that bolts are secure and tight. Quick clips should

be completely closed and threaded clips screwed tight.

If squeaking occurs lubricate bushings with oil or WD-40®.

SWINGS, ROPES AND RIDES:

Reinstall if removed during cold season. Check all

moving parts including swing seats, ropes, chains and

attachments for wear, rust and other deterioration.

Replace as needed.

Check that ropes are tight, secure at both ends and

cannot loop back as to create an entrapment.

WOOD PARTS:

Check all wood members for deterioration, structural

damage and splintering. Sand down splinters and replace

deteriorated wood members. As with all wood, some

checking and small cracks in grain is normal.

Unprotected, they will appear weathered over time.

Periodic application of an exterior water repellent or stain

(water-based) will help improve appearance and life.

Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor

products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important

that you, the owner, properly maintain it.

Check the following at the beginning of the play season:

HARDWARE:

Inspect for tightness. Must be ﬁrmly against, but not

crushing the wood. DO NOT OVER-TIGHTEN.

This will cause splintering of wood.

Check for sharp edges or protruding screw threads.

Add washers if required.

SHOCK ABSORBING SURFACING:

Rake and check depth of loose ﬁll protective surfacing

materials to prevent compaction and maintain appropriate

depth. Replace as necessary.

(See Protective Surfacing, page 3)

Check twice a month during play season:

SWING HANGERS:

Check that they are secure and orientated correctly. Hook

should rotate freely and perpendicular to support beam.

If squeaking occurs lubricate bushings with oil or WD-40®.

SWINGS AND RIDES:

Check swing seats, all ropes, chains and attachments for

fraying, wear, excessive corrosion or damage.

Replace if structurally damaged or deteriorated.

Check once a month during play season:

SWINGS AND RIDES:

To prolong their life, remove swings and store inside

when outside temperature is below 32°F/0°C. Below

freezing, plastic parts may become more brittle.

SHOCK ABSORBING SURFACING:

Rake and check depth of loose ﬁll protective surfacing

materials to prevent compaction and maintain appropriate

depth. Replace as necessary.

(See Protective Surfacing, page 3)

Check at the end of the play season:

If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards

at the time it is discarded. Be sure to follow your local waste ordinances.

Use an extra

Flat Washer

If Bolt protrudes

beyond T-Nut

4

About Our Wood

KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we

take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible

to weathering which can change the appearance of your set.

What causes weathering? Does it affect the strength of my Play System?

One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is

different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can

result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of

the product:

1. Checking is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)

because the surface and interior moisture content will vary more widely than in thinner wood.

2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid

wetting and drying of the wood.

3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.

How can I reduce the amount of weathering to my Play System?

At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption

during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we recommend applying a

water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended product).

Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are

concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.

Complete and mail registration card to receive important product notifications and assure prompt

warranty service.

5 Year Limited Warranty

KidKraft warrants that this product is free from defect in materials and workmanship for a period of one

year from the original date of purchase. In addition, lumber is warranted for 5 years against structural

failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and

slides carry a one-year warranty only.

This warranty applies to the original owner and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your Play System. This warranty does not

cover any inspection cost.

This Limited Warranty does not cover:

• Labor for replacement of any defective item(s);

•Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

•Vandalism; improper use or installation; acts of nature;

•

Minor twisting, warping, checking, or any other natural occurring properties of wood that do not

affect performance or integrity.

KidKraft products have been designed for safety and quality. Any modifications made to the original

product could damage the structural integrity of the unit leading to failure and possible injury.

Kidkraft cannot assume any responsibility for modified products. Furthermore, modification voids

any and all warranties.

This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a

KidKraft Play System be used in public settings such as schools, churches, playgrounds, parks, day

cares and the like. Such use may lead to product failure and potential injury. Any and all public use

will void this warranty.

KidKraft disclaims all other representations and warranties of any kind, express or implied.

This Warranty gives you speciﬁc legal rights. You may have other rights as well which vary from state to state or

province to province. This warranty excludes all consequential damages, however, some states do not allow the

limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

5

Part Identication Key

On each page, you will nd the parts

and quantities required to complete

the assembly step illustrated on that

page. Here is a sample.

Key Number: The rst two digits

represent the step number. The third

digit represents the piece. Note that if

the part is used in multiple steps then

the number only reects the rst step

it is used in.

Symbols

Throughout these instructions symbols are provided as important reminders for proper and safe assembly.

Proper Hardware Assembly

Lag screws require drilling pilot

holes to avoid splitting wood. Only a

at washer is required. For ease of

installation liquid soap can be used

on all lag-type screws.

For bolts, tap T-Nut into hole with

hammer. Insert the hex bolt through

lock washer rst then at washer

then hole. Because the assemblies

need to be squared do not completely

tighten until instructed. Pay close

attention to diameter of the bolts.

5/16” is slightly larger than 1/4”.

Note: Wafer head bolts with blue lock

tight or a bolt with a Ny-Lok nut do

NOT require a lock washer.

Once the assembly is tightened, watch for exposed

threads. If a thread protrudes from the T-Nut, remove

the bolt and add washers to eliminate this condition.

Extra washers have been provided for this purpose.

This identies information that requires

special attention. Improper assembly could

lead to an unsafe or dangerous condition.

Where this is shown, 2 or 3

people are required to safely

complete the step. To avoid

injury or damage to the

assembly make sure to

get help!

Check that assembly is square

before tightening bolts.

Use a measuring tape to

assure proper location.

Check that set or assembly is properly level

before proceeding.

Pre-drill a pilot hole

before fastening screw

or lag to prevent

splitting of wood.

This indicates time to tighten bolts, but

not too tight! Do not crush the wood.

This may create splinters and cause

structural damage.

Use

Help

Use

Help

Measure

Distance

Square

Assembly

Use

Level

Pre-drill 1/8” & 3/16” Bit

Tighten

Bolts

No Yes

CAUTION – Protrusion Hazard

Keys to Assembly Success

Tools Required

• Tape Measure

• Carpenters Level

• Carpenters Square

• Claw Hammer

• Standard or Cordless Drill

• #1, #2 & #3 Phillips

or Robertson Bits

or Screwdriver

• Ratchet with extension

(1/2” & 9/16” sockets)

• Open End Wrench

(7/16”, 1/2” & 9/16”)

• Adjustable Wrench

• 1/8” & 3/16” Drill Bits

• Pencil

• 3/16” Hex Key

• 8’ Step Ladder

• Safety Glasses

• Adult Helpers

Quantity Key Number Part Description,

Part Size

2X 012 Post 2 x 4 x 83”

Use an extra

Flat W asher

If Bolt protrudes

beyond T-Nut

Lag Screw

Flat Washer

Lag Assembly

Before mounting Lag Screw,

use factory drilled holes as

guides to drill 1/8” pilot holes

Hex Bolt

Bolt Assembly

T-Nut

(Hammer into place)

Do not crush wood!

Lock

Washer

Flat

Washer

6

Key Number: The rst two digits represent the step

number. The third digit represents the order in which

the part is listed in the step.

Note that if the part is used in multiple steps then

the key number only reects the rst step it is used in.

Part Quantity Key Number

Order Listed

(The order the part is

listed in step 1)

Part Description Part Size

2X 012 Post 2 x 4 x 83”

00

Your Key To Quick Assembly

SAVE TIME - TIP #1:

Wood parts are found in Box 2, 3, 4 & 5. Open each box with wood parts and

look for the Key Number stamped on the end of the wood part (see chart below).

Sort each wood part into the different assembly steps.

SAVE TIME - TIP #2:

In addition to the key number stamp, you can also identify the wood parts by

using the Parts Identication pages in the manual or the Parts Identication

weather resistant poster.

HARDWARE:

The majority of each hardware part comes packed in a separate bag so

you do not need to sort the hardware. Each assembly step indicates which

hardware (bolt, screw, washer etc.) you will require to complete the step.

SORTING WOOD PARTS INTO

EACH ASSEMBLY STEP WILL

SAVE TIME!

Step Step Step

01 2

Step Number

(This is Step 1)

7

1 inch = 25.4mm

KIDKRAFT DESIGN HARDWARE

For example:

BOLT LENGTH 4½ (4.5) inches long

114mm long

1 inch = 25.4mm

25.4mm

4.5 inches x

DIAMETER CONVERSION

LENGTH CONVERSION

=

BOLT DIAMETER 5/16 (0.31) inches

0.31 inches

x 25.4mm = 8mm

For example:

HARDWARE LENGTH CHART

inches vs millimetres

6 152

5½ 140

5 127

4½

114

4 102

3½ 89

3 76

2½ 64

2 51

1½ 38

1¼ 32

1-

1/8

29

1 25.4

7/8 22

3/4 19

1/2 12.7

1/4" (6mm) Flat Washer

1/4" (6mm)

Lock Washer

1/4"(0.25) = 6mm Hex Bolt

1/4" (6mm)

T-Nut

5/16"(.31) = 8mm Lag Screw

5/16" (8mm)

Flat Washer

1/4"(0.25) = 6mm Lag Screw

1/4" (6mm)

Flat Washer

5/16" (8mm)

Flat Washer

5/16" (8mm) Lock Washer

5/16"(.31) = 8mm Hex Bolt

5/16" (8mm)

T-Nut

3/8"(.38) = 9.5mm Lag Screw

3/8" (9.5mm)

Flat Washer

8

9

1 x 2

1 x 4

1 x 5

1 x 6

1 x 3

1/2 x 4

5/4 x 6

5 1/2"

139.7

1"

25.4

11.1

.44

82.6

3 1/4"

4 x 4

3 1/2"

88.9

3 1/2"

88.9

4 1/2"

114.3

5/8"

15.9

5/8"

1 3/8"

34.9

2 x 6

5 3/8"

136.5

1 1/2"

38.1

15.9

5/8" 3 3/8"

85.7

60.3

2 3/8"

15.9

5/8"

1505mm

KIDKRAFT DESIGN WOOD PROFILES

LENGTH CONVERSION

For example:

1 inch = 25.4mm

BOARD LENGTH 59¼ (59.25) inches

59.25 inches

x 25.4mm =

Dimensions in brackets

[mm] represent millimetres.

5/4 x 4

3 1/2"

88.9

1"

25.4

5 3/8"

136.5

5/8"

15.9

2 x 4

3 3/8"

85.7

1 3/8"

34.9

5/4 x 5

4 1/2"

114.3

1"

25.4

2 x 3

2 1/2"

63.5

1 3/8"

34.9

5/4 x 3

63.5

2 1/2"

25.4

1"

2

x 2

1 1/2"

38.1

1 1/2"

38.1

Nominal Size Actual Size

1-1/4 x 1-1/2 1-1/4 x 1-1/2

1 x 2 5/8 x 1-3/8

1 x 3 5/8 x 2-3/8

1 x 4 5/8 x 3-3/8

1 x 5 5/8 x 4-3/8

Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

1pc.

-

8073

-

1 x 2 x 22" - Dormer Bottom - Box 4 -

3638073

2pc.

-

8072

-

1 x 3 x 6-3/4" - Dormer Side Burst - Box 4 -

3638072

2pc.

-

2503

-

1 x 5 x 32-1/2" - Wall Board - Box 4 - 3632503

2pc.

-

8613

-

1 x 4 x 10-15/16" - Gable Board A - Box 4 - 3638613

1pc.

-

8612

-

1 x 4 x 16-1/8" - Centre Gable Board - Box 4 -

3638612

3pc.

-

8039

-

1 x 4 x 26-1/2" - Wall Board - Box 3 -

3638039

1pc.

-

8513

-

1 x 4 x 22-1/8" - Board Access - Box 2 -

3638513

1pc.

-

2494

-

1 x 5 x 57" - Middle Back - Box 3 - 3632494

1pc.

-

8074

-

1 x 4 x 5-1/2" - Dormer Burst - Box 4 - 3638074

1pc.

-

8071

-

1 x 3 x 10-3/4" - Dormer Centre - Box 4 -

3638071

2pc.

-

8070

-

1 x 3 x 13-5/8" - Dormer Side - Box 4 -

3638070

9pc.

-

2750

-

1 x 5 x 27" - Floor Board 1 x 5 x 27" - Box 3 - 3632750

6pc.

-

0318

-

- Ground Stake 1-1/4 x 1-1/2 x 14" - Box 1 -

3650318

1pc.

-

2505

-

1 x 4 x 29-3/4" - Top End Nest - Box 3 - 3632505

1pc.

-

2479

-

1 x 5 x 38-1/2" - Floor Board - Box 2 - 3632479

10

5pc.

-

8511

-

1 x 6 x 22-1/8" - Board Rock A - Box 2 -

3638511

5pc.

-

8512

-

1 x 6 x 22-1/8" - Board Rock B - Box 2 -

3638512

2pc.

-

2508

-

5/4 x 4 x 7-3/4" - Short Rail - Box 4 -

3632508

1pc.

-

8516

-

5/4 x 3 x 35 -7/8" - Top Ladder - Box 2 -

3638516

2pc.

-

2483

-

5/4 x 3 x 34-1/4" - SW Table Top - Box 3 -

3632483

2pc.

-

2517

-

5/4 x 2 x 17" - Spindle - Box 4 -

3632517

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)

Nominal Size Actual Size

1 x 6 5-1/4

5/4 x 2 15/16 x 1-1/2

5/4 x 3 15/16 x 2-1/4

5/4 x 4 15/16 x 3-1/4

1pc.

-

2480

-

1 x 6 x 57" - Back Top - Box 3 -

3632480

20pc.

-

2515

-

5/4 x 2 x 33" - Long Spindle - Box 3 -

3632515

2pc.

-

2519

-

1 x 6 x 31" - SW Nest Wall - Box 3 -

3632519

12pc.

-

2478

-

1 x 6 x 38-1/2" - Floor - Box 2 -

3632478

1pc.

-

2522

-

1 x 6 x 21" - Gable A - Box 3 -

3632522

2pc.

-

2339

-

1 x 6 x 25-3/8" - Crowsnest Floor - Box 3 -

3632339

1pc.

-

8515

-

1 x 6 x 22-1/8" - Access Rock Bottom - Box 2 -

3638515

11

Nominal Size Actual Size

5/4 x 4 15/16 x 3-1/4

5/4 x 5 15/16 x 4-1/4

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

2pc.

-

2507

-

5/4 x 4 x 33-7/8" - Side Nest Top - Box 3 -

3632507

1pc.

-

2506

-

5/4 x 4 x 29-3/4" - Bottom Nest End - Box 3 -

3632506

1pc.

-

2498

-

5/4 x 4 x 24-1/4" - Cafe Top - Box 3 -

3632498

1pc.

-

8514

-

5/4 x 4 x 15" - Gap Ladder - Box 2 -

3638514

2pc.

-

2748

-

5/4 x 6 x 13¼" - End Nest Board - Box 3 -

3632748

2pc.

-

2492

-

5/4 x 4 x 57" - Front Top Bottom - Box 3 -

3632492

1pc.

-

2474

-

5/4 x 4 x 88-43/64" - Ground SW - Box 3 -

3632474

1pc.

-

2487

-

5/4 x 5 x 15-5/8" - Crowsnest Bottom Front - Box 2 -

3632487

1pc.

-

2495

-

5/4 x 4 x 13-5/8" - Bench Support - Box 3 -

3632495

1pc.

-

2493

-

5/4 x 4 x 54-1/2" - Back Ground - Box 3 -

3632493

2pc.

-

2509

-

5/4 x 4 x 39-1/4" - Lower Side - Box 3 -

3632509

2pc.

-

2499

-

5/4 x 4 x 34" - Roof Support Left - Box 3 -

3632499

4pc.

-

8517

-

5/4 x 4 x 13-3/4" - Ladder Tread - Box 2 -

3638517

1pc.

-

2520

-

5/4 x 4 x 29-3/4" - End Nest Top - Box 3 -

3632520

2pc.

-

2518

-

5/4 x 4 x 34" - Roof Support Right - Box 3 -

3632518

12

1pc.

-

2481

-

5/4 x 5 x 34-1/8" - Lower Back - Box 2 -

3632481

1pc.

-

8614

-

5/4 x 6 x 10" - Sunburst - Box 4 -

3638614

2pc.

-

2341

-

5/4 x 4 x 34-3/8" - Crowsnest Upright - Box 3 -

3632341

2pc.

-

2337

-

5/4 x 4 x 25-1/2" - Crowsnest Back - Box 4 -

3632337

1pc.

-

2497

-

5/4 x 6 x 29-1/2" - Seat - Box 3 -

3632497

1pc.

-

2524

-

5/4 x 5 x 32-7/8" - SL Bottom - Box 3 -

3632524

Nominal Size Actual Size

5/4 x 5 15/16 x 4-1/4

5/4 x 6 15/16 x 5-1/4

5/4 x 4 1 x 3-1/2

2 x 3 1-1/2 x 2-1/4

2 x 4 1-1/2 x 3-1/4

2pc.

-

2488

-

5/4 x 5 x 15-5/8" - Crowsnest Top Front - Box 3 -

3632488

2pc.

-

2485

-

5/4 x 6 x 5" - Seat Side - Box 2 -

3632485

Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

2pc.

-

2747

-

2 x 4 x 9 7/8" - Gusset - Box 4 -

3632747

2pc.

-

2516

-

2 x 3 x 25" - SW Nest Access Post - Box 3 -

3632516

1pc.

-

8168

-

2 x 4 x 26-1/4" - SL Support - Box 3 -

3638168

1pc.

-

2484

-

2 x 4 x 13-1/2" - Bench Leg - Box 4 -

3632484

1pc.

-

2496

-

2 x 4 x 3-1/4" - Seat Block - Box 4 -

3632496

1pc.

-

2491

-

2 x 3 x 42-1/4" - Diagonal - Box 3 -

3632491

13

Nominal Size Actual Size

2 x 4 1 3/8 x 3-3/8

1-1/4 x 3-3/8 1-1/4 x 3-3/8

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

1pc.

-

2490

-

2 x 4 x 33-1/8" - Rockwall Spacer - Box 2 -

3632490

2pc.

-

2510

-

2 x 4 x 38" - Floor Support - Box 3 -

3632510

2pc.

-

2500

-

2 x 4 x 38-3/8" - Crowsnest Post - Box 4 -

3632500

1pc.

-

2489

-

2 x 4 x 38-1/2" - Floor End - Box 2 -

3632489

1pc.

-

8611

-

2 x 4 x 41" - Gable Bottom - Box 4 -

3638611

1pc.

-

2482

-

2 x 4 x 47-7/8" - Back Wall Support - Box 4 -

3632482

1pc.

-

8139

-

2 x 4 x 62-7/8" - Rock Rail - Box 2 -

3638139

1pc.

-

8145

-

2 x 4 x 62-7/8" - Left Access Rail - Box 2 -

3638145

1pc.

-

8146

-

2 x 4 x 62-7/8" - Right Access Rail - Box 2 - 3638146

1pc.

-

2475

-

2 x 4 x 68" - FR Floor Support - Box 2 -

3632475

1pc.

-

2476

-

2 x 4 x 68" - Floor Joist - Box 2 -

3632476

1pc.

-

2477

-

2 x 4 x 68" - Back Floor Support - Box 2 -

3632477

2pc.

-

2473

-

2 x 4 x 102" - Post - Box 4 -

3632473

2pc.

-

2521

-

1-1/4 x 3-3/8 x 23-3/4" - SW Side Post - Box 4 -

3632521

14

4pc.

-

2511

-

2 x 3 x 37-5/8" - Nest Post - Box 3 -

3632511

Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

1pc.

-

2523

-

2 x 6 x 31-3/4" - Lower Gable - Box 3 -

3632523

Nominal Size Actual Size

2 x 6 1-1/4 x 5-1/4

2 x 3 1-3/8 x 2-1/2

2 x 4 1-3/8 x 3-3/8

2 x 2 1-1/2 x 1-1/2

2 x 6 1-1/2 x 5-3/8

2 x 3-3/8 2 x 3-3/8

3pc.

-

2340

-

2 x 4 x 8-5/8" - Crowsnest Joist - Box 4 -

3632340

1pc.

-

8069

-

2 x 4 x 10" - Dormer Cleat - Box 3 -

3638069

2pc.

-

2338

-

2 x 4 x 27-1/2" - Crowsnest Face - Box 3 -

3632338

1pc.

-

2501

-

2 x 4 x 38-1/2" - Crowsnest Top - Box 3 -

3632501

1pc.

-

2502

-

2 x 4 x 38-1/2" - Crowsnest Floor End - Box 3 -

3632502

2pc.

-

2504

-

2 x 2 x 13-3/8" - SW Ladder Step - Box 3 -

3632504

2pc.

-

2746

-

2 x 3 x 83 3/16" - Heavy Post SW - Box 4 -

3632746

1pc.

-

2614

-

4 x 6 x 88" - Engineered Beam - Box 4 -

3632614

1pc.

-

2615

-

4 x 4 x 50-15/16" - SW Upright - Box 3 -

3632615

1pc.

-

2616

-

5/4 x 4 x 46-1/2" - SW Support - Box 3 -

4632616

15

1pc.

-

8068

-

- Dormer Roof Set - Box 4 -

3638068

Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) Part Identification (Reduced Part Size)

2pc.

-

2525

-

1-1/4 x 35-7/16 x 64" - Roof Panel - Box 2 -

37632525

16

1pc.

-

2741

-

1-1/4 x 38-1/2 x 83"

SW Wall Panel - Box 2 -

37632741

1pc.

-

2527

-

1-1/4 x 28-1/2 x 102"

Chalkwall Panel - Box 4 -

37632527

Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)Part Identification (Reduced Part Size)

1pc.

-

2724

-

1-1/4 x 28-1/2 x 102"

Cafe Panel - Box 4 - 37632724

1pc.

-

2529

-

1-1/4 x 38-1/2 x 54-1/8"

SL Side Panel - Box 2 -

37632529

17

5pc. LS2

- Lag Screw

1/4 x 2-1/2" - (9272222)

21pc. H3

-

Hex Bolt 1/4 x 2-1/2"

- (9277222)

6pc.

H2

-

Hex Bolt 1/4 x 2" - (9277220)

4pc. H11

-

Hex Bolt 1/4 x 2-3/4"

- (9277223)

3pc.

H13

-

Hex Bolt 1/4 x 3-1/2" - (9277232)

2pc.

G25

-

Hex Bolt 5/16 x 7-1/4" - (9277471)

35pc. H10

-

Hex Bolt 1/4 x 2-1/4" - (9277221)

3pc.

H12

-

Hex Bolt 1/4 x 3"

- (9277230)

Hardware Identification (Actual Size)

17pc. WL5

- Wafer Lag

1/4 x 2-1/2"

-

(52632222)

8pc.

WL3

- Wafer Lag

1/4 x 1-3/8"

- (9266216)

3pc.

WB7

-

Hex Bolt 5/16 x 3"

- (9276330)

5pc.

G1

-

Hex Bolt 5/16 x 1-1/2"

- (9277312)

3pc.

G4

-

Hex Bolt 5/16 x 4" - (9277340)

4pc.

G8

-

Hex Bolt 5/16 x 2" - (9277320)

7pc. G21

-

Hex Bolt 5/16 x 3¾"

- (9277333)

14pc.

G7

-

Hex Bolt 5/16 x 5-1/2" - (9277352)

18

40pc. S8

- Pan Screw

#12 x 3/4" - (9264603)

230pc.

S20

- Wood Screw

#8 x 1-3/8" - (9260516)

89pc.

PB1

- Pan Bolt

1/4 x 3/4"

- (53452203)

4pc.

S18

- Wood Screw

#6 x 1"

- (9264010)

13pc. PB2

- Pan Bolt

1/4 x 1-1/4"

- (53432212)

89pc.

LN1

-

1/4 Lock Nut

- (9283200)

8pc.

FW6

- #12 Screw Bezel - (9299500)

94pc.

FW1

- 1/4" Flat Washer - (9251200)

5pc.

PB6

- Pan Bolt

1/4 x 1" - (9274210)

15pc.

TN2

- 5/16" T- Nut

- (9285300)

18pc.

LW2

- 5/16" Lock Washer - (9253300)

29pc. LN2

- 5/16" Lock Nut

-

(9283300)

80pc.

TN1

- 1/4" T - Nut

-(9285200)

10pc. BN1

- 1/4" Barrel Nut

- (9248200)

75pc.

FW2

- 5/16" Flat Washer - (9251300)

90pc.

LW1

- 1/4" Lock Washer - (9253200)

18pc.

FW0

- 3/16" Flat Washer - (9251100)

73pc.

S3

- Wood Screw

#8 x 2-1/2" - (9290522)

22pc.

S1

- Wood Screw

#8 x 1-1/8" - (9290514)

18pc.

S5

- Pan Screw

#8 x 1/2" - (9264504)

12pc.

S10

- Pan Screw

#8 x 1"

- (9264510)

97pc.

S15

- Wood Screw

#8 x 1-3/4"

- (9260513)

15pc.

S6

- Pan Screw

#12 x 1" - (9264610)

28pc.

S4

- Wood Screw

#8 x 3"

- (9290530)

61pc. S7

- Pan Screw

#12 x 2" - (9264620)

Hardware Identification (Actual Size)

19

1x

- Swing Hanger (4 Pk)

(3200106)

1x

- Beam Brkt.Set (3200143)

1x

- 2x2 Robertson

Driver

(9200014)

1x

-

Glider Brkt.& Mount (2pk)

(3200105)

1x

- Cedar Summit Plaque

(9320358)

1x

- Quadrex Driver

(9200015)

2x

- 42" Belt Swing w/

Welded Chain

(3724943) Yellow

2x

- Hand Grip (2Pk)

(3320240) -Yellow

9201580

1X - Wall Angle

Bracket

1x

- 39" Glider Rope & Chain

(4Pk)

(3533860)

1x

- TNR 2 Slide Support

(9200226)

1x

- TNR 2 Post Mount

(9200203)

1x

- TNR 2 Slide Exit Top

(3310224)

9x

- TNR 2 Slide Elbow

(3310221)

1x

- TNR 2 Slide Exit

(3310220)

10x

- TNR 2 Slide Clamp Ring

(3300220)

1x

- TNR 2 Slide Lt Flange

(3310222)

1x

- TNR 2 Slide Rt Flange

(3310223)

2x

- Space Glider Handle

(3320177) Green

1x

- Space Glider Body

(3320268) Yellow

9200628

8X - Corner Panel

Brkt

9201570

4X - Corner

Bracket

9200633

2X - Flat Panel

Brkt

1x

- Telescope w/ Mount

(3320161)

1x

- EN71 Hand Rail

(9200223) -Yellow

1x

- (5pk) Swing Bracket Set

(3201531) -Green

1x.

- Rocks (10pk)

(3320210) -Green/Yellow/Burgundy

Part Identification (Reduced Part Size)

1x - Spin Chalk Sign

(3320715)

1x

- Beam L Brkt.

(3200145) (2pk)

1x

- Cedar Summit ID Plaque

(9320357)

1x

- Bayfield Retreat Brkt Set

(3203910)

1x - KidKraft ID

Plaque (9320374)

7310248

Yellow

é

9320370

Part Identication (Reduced Part Size)

10x - TNR 2 Clamp Ring

(9300220) (Yellow)

10pcs number 3300220

20

1x - KidKraft Logo

Plaque (3320353)

Page is loading ...

KidKraft Abbeydale Clubhouse Wooden Playset Assembly Instruction

KidKraft Abbeydale Clubhouse Wooden Playset Assembly Instruction

Related papers

Other documents