Enclume WR3 HS User manual

Brand: Enclume

Model: WR3 HS

Type: User manual

Enclum e UTENSIL BARS

WR0, WR1, WR2, WR3, WR4, WR5

Enclume racks are the ultimate in

Storage racks made.

WARNING:

READ ALL OF THE INSTRUCTIONS

BEFORE ASSEMBLING AND USING

YOUR RACK.

All of our hammered steel racks are finished with an industrial wax designed to

give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry

thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"

like wax product.

Enclosed you will find everything needed for the assembly

and use of your storage rack. Two people make assembly

and installation easier. The parts and hardware included are:

Hardware included:

2 – 2” Lag Screws

Toggle Kit

Components included:

1 – Utensil Bar

12 – Straight Pot Hooks – 48” bar

12 – Straight Pot Hooks – 42” bar

6 – Straight Pot Hooks – 36” bar

6 – Straight Pot Hooks – 30” bar

6 – Straight Pot Hooks – 24” bar

6 – Straight Pot Hooks – 18” bar

See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS

If you need help, please call 1-877-ENCLUME

Enclume Design Products, Inc.

24 Colwell Street, Port Hadlock, WA. 98339

Phone 360-385-6100  Fax 360-385-6156

www.enclume.com

Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall

be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the

warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid

within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the

customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.

ASSEMBLY AND INSTALLATION INSTRUCTIONS for WR0, WR1, WR2, WR3, WR4, WR5

Enclosed you will find everything needed for the assembly

and use of your storage rack. Two people make assembly

and installation easier. The parts and hardware included are:

Hardware included:

2 – 2” Lag Screws

Toggle Kit

Components included:

1 – Utensil Bar

12 – Straight Pot Hooks – 48” bar

12 – Straight Pot Hooks – 42” bar

6 – Straight Pot Hooks – 36” bar

6 – Straight Pot Hooks – 30” bar

6 – Straight Pot Hooks – 24” bar

6 – Straight Pot Hooks – 18” bar

ASSEMBLY AND INSTALLATION INSTRUCTIONS

Rack Assembly

1) If your utensil bar is plated it is best to keep the tissue on during installation to avoid fingerprinting.

2) Mount the bar onto the wall using the two lag screws. The Lag Screws must go into the solid wood or into a wooden stud.

If your kitchen construction does not allow direct mounting into wood, consider mounting your utensil bar to an attractive piece

of finished lumber and mounting that where studs allow. If you are mounting into plaster wall, use the Toggles provided and

follow the directions in the kit.

3) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is

easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax

product.

4) The care and cleaning of copper and brass units must be done with a non-abrasive cleaner such as “Flitz”. Chrome racks are best

cleaned with a good quality glass cleaner. Our high quality plating will age and tarnish the same as solid material. A periodic

cleaning will restore your rack to its original brilliance.

It is important that your rack is assembled correctly. If the unit is assembled or used

incorrectly, it could become unstable and collapse, possibly causing injury.

If you need help, please call 1-877-ENCLUME

Enclume Design Products, Inc.

24 Colwell Street, Port Hadlock, WA. 98339

Phone 360-385-6100  Fax 360-385-6156

www.enclume.com

WARNING

Enclume WR3 HS User manual

Enclume WR3 HS User manual

Enclume WR3 HS User manual

Related papers

Other documents