Sink
Sink
Sink
Sink
Rubber
gasket
Rubber
gasket
Rubber
gasket
Rubber
gasket
Plastic
friction
washer
Plastic
friction
washer
Plastic
friction
washer
Plastic
friction
washer
Style “C”
Style “C”
Style “C”
Style “C”
Sink
Sink
Sink
Sink
Steel
flanged
washer
Steel
flanged
washer
Steel
flanged
washer
Steel
flanged
washer
Steel 3 screw
rapid mount
assembly
Steel 3 screw
rapid mount
assembly
Steel 3 screw
rapid mount
assembly
Steel 3 screw
rapid mount
assembly
Tail piece
poly washer
Tail piece
poly washer
Tail piece
poly washer
Tail piece
poly washer
Tail piece
nut
Tail piece
nut
Tail piece
nut
Tail piece
nut
1. Remove tail piece nut.
2. Remove tail piece poly washer.
3. Remove steel 3 screw rapid mount
assembly.
4. Remove steel flanged washer.
5. Remove rubber gasket.
6. Remove plastic friction washer.
Gently pull away from Rapid Ring
plumbers putty and save.
7. Clean sink opening and insert
complete body assembly above sink
through opening. Rapid Ring plumbers
putty pre-installed. Simply position body
centered in sink opening. Make sure
your sink is compatible with standard
plumbers putty.
8. From under sink, re-install rubber gasket.
Gasket will rest against bottom of sink.
9. Re-install plastic friction washer.
10. Re-install steel flanged washer. Note: Flush
side toward washers, screws tighten
inside rim.
11. Re-install 3 screw rapid mount assembly and
tighten with pliers or flat screwdriver. Note: Putty will begin
to compress against inside of sink bowl. After assembly is
securely tightened, remove and discard excess putty.
1. Remove tail piece nut.
2. Remove tail piece poly washer.
3. Remove steel 3 screw rapid mount
assembly.
4. Remove steel flanged washer.
5. Remove rubber gasket.
6. Remove plastic friction washer.
Gently pull away from Rapid Ring
plumbers putty and save.
7. Clean sink opening and insert
complete body assembly above sink
through opening. Rapid Ring plumbers
putty pre-installed. Simply position body
centered in sink opening. Make sure
your sink is compatible with standard
plumbers putty.
8. From under sink, re-install rubber gasket.
Gasket will rest against bottom of sink.
9. Re-install plastic friction washer.
10. Re-install steel flanged washer. Note: Flush
side toward washers, screws tighten
inside rim.
11. Re-install 3 screw rapid mount assembly and
tighten with pliers or flat screwdriver. Note: Putty will begin
to compress against inside of sink bowl. After assembly is
securely tightened, remove and discard excess putty.
1. Remove tail piece nut.
2. Remove tail piece poly washer.
3. Remove steel 3 screw rapid mount
assembly.
4. Remove steel flanged washer.
5. Remove rubber gasket.
6. Remove plastic friction washer.
Gently pull away from Rapid Ring
plumbers putty and save.
7. Clean sink opening and insert
complete body assembly above sink
through opening. Rapid Ring plumbers
putty pre-installed. Simply position body
centered in sink opening. Make sure
your sink is compatible with standard
plumbers putty.
8. From under sink, re-install rubber gasket.
Gasket will rest against bottom of sink.
9. Re-install plastic friction washer.
10. Re-install steel flanged washer. Note: Flush
side toward washers, screws tighten
inside rim.
11. Re-install 3 screw rapid mount assembly and
tighten with pliers or flat screwdriver. Note: Putty will begin
to compress against inside of sink bowl. After assembly is
securely tightened, remove and discard excess putty.
1. Remove tail piece nut.
2. Remove tail piece poly washer.
3. Remove steel 3 screw rapid mount
assembly.
4. Remove steel flanged washer.
5. Remove rubber gasket.
6. Remove plastic friction washer.
Gently pull away from Rapid Ring
plumbers putty and save.
7. Clean sink opening and insert
complete body assembly above sink
through opening. Rapid Ring plumbers
putty pre-installed. Simply position body
centered in sink opening. Make sure
your sink is compatible with standard
plumbers putty.
8. From under sink, re-install rubber gasket.
Gasket will rest against bottom of sink.
9. Re-install plastic friction washer.
10. Re-install steel flanged washer. Note: Flush
side toward washers, screws tighten
inside rim.
11. Re-install 3 screw rapid mount assembly and
tighten with pliers or flat screwdriver. Note: Putty will begin
to compress against inside of sink bowl. After assembly is
securely tightened, remove and discard excess putty.
Rapid Ring plumbers putty
pre-installed! Gently pull
away and SAVE plastic
friction washer BEFORE
setting into sink!
Rapid Ring plumbers putty
pre-installed! Gently pull
away and SAVE plastic
friction washer BEFORE
setting into sink!
Rapid Ring plumbers putty
pre-installed! Gently pull
away and SAVE plastic
friction washer BEFORE
setting into sink!
Rapid Ring plumbers putty
pre-installed! Gently pull
away and SAVE plastic
friction washer BEFORE
setting into sink!
Body assembly
Body assembly
Body assembly
Body assembly
RP-INS-C
RP-INS-C
RP-INS-C
RP-INS-C
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
American Standard 7105801.295 Installation guide
-
Glacier Bay QK004 Installation guide
-
-
-
-
Symmons SLW-4512-1.5 Installation guide
-
Symmons SLW-4512-1.5 Installation guide
-
-
-