Taylor 8757 User manual

OPERATOR'S

MANUAL

Model 8752, 8756, & 8757

Soft Serve Freezers

Original Operating Instructions

028752- M

8/99 (Original Publication)

(Updated 8/14/14)

Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum Fuse Size: Amps

Minimum Wire Ampacity: Amps

Part Number:

E 1999 Carrier Commercial Refrigeration, Inc.

028752- M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work may be

a violation of Copyright Law of the United States of America and other countries, could result in the awarding of Statutory

Damages of up to $250,000 (17 USC 504) for infringement, and may result in further civil and criminal penalties.

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Table of Contents Models 8752, 8756, & 8757

Table of Contents

Section 1 To the Installer 1............................................

Section 2 To the Operator 4...........................................

Section 3 Safety 5....................................................

Section 4 Operator Parts Id en t ificatio n 7...............................

Model 8752 7..........................................................

8752 Beater Door Assembly 9............................................

Model 8756 11..........................................................

Model 8757 13..........................................................

8756 & 8757 Beater Door Assembly 15.....................................

Accessories 16..........................................................

Section 5 Important: To the Operator 17.................................

Symbol Definitions 18....................................................

Power Switch 18.........................................................

Indicator Lights - MIX LOW and MIX OUT 18................................

Reset Button 18.........................................................

SOFTECH Control Operation 18...........................................

MIX REF 18.............................................................

Standby 19..............................................................

Wash 19................................................................

Auto 19.................................................................

Pump 19................................................................

Adjustable Draw Handle 19...............................................

Section 6 Operating Procedures 20.....................................

Prior to Set- Up (Model 8757) 20...........................................

Assembly 20............................................................

Air/Mix Pump Assembly 24................................................

Air/Mix Pump Assembly Exploded View 28..................................

Sanitizing 29............................................................

Priming 31..............................................................

Closing Procedure 32....................................................

Draining Product From the Freezing Cylinder 32.............................

Table of Contents Models 8752, 8756, & 8757

Table of Contents - Page 2

Rinsing 33..............................................................

Cleaning 33.............................................................

Disassembly 34..........................................................

Brush Cleaning 34.......................................................

Check Topping Pump Temperature and Volume - Model 8757 35..............

Section 7 Important: Operator Checklist 36..............................

During Cleaning and Sanitizing 36.........................................

Troubleshooting Bacterial Count 36........................................

Regular Maintenance Checks 36...........................................

The Air/Mix Pump 37.....................................................

Winter Storage 37........................................................

Section 8 Troubleshooting Guide 38....................................

Section 9 Parts Replacement Schedule 43...............................

Section 10 Limited Warranty on Equipment 44............................

Section 11 Limited Warranty o n Parts 46.................................

Section 12 Parts List 49.................................................

Wiring Diagrams 61......................................................

Note: Cont in u ing research results in stead y improvements; th erefore, information

in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation

representative(s) are considered to be the original set of instructions.

E 1999 Carrier Commercial Refrigeration, Inc. (Original Publication)

(Updated August, 2014)

028752- M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work

may be a violation of Copyright Law of the United States of America and other countries, could result in the

awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

1

Models 8752, 8756, 8757 To the Installer

131210

Section 1 To the Installer

The following information has been included in the

manual as safety and regulatory guidelines. For

complete installation instructions, please see the

Installation Checklist.

Installer Safety

In all areas of the world, equipment should be

installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

service of Taylor equipment.

S Only authorized Taylor service personnel

should perform installation and repairs on the

equipment.

S Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the

industry standards on lockout/tagout

procedures before beginning any installation

or repairs.

S Authorized service personnel must ensure

that the proper PPE is available and worn

when required during installation and service.

S Authorized service personnel must remove all

metal jewelry, rings, and watches before

working on electrical equipment.

The main power supply(s) to the freezer must

be disconnected prior to performing any repairs.

Failure to follow this instruction may result in personal

injury or death from electrical shock or hazardous

moving parts as well as poor performance or damage

to the equipment.

Note:Allrepairsmustbeperformedbyan

authorized Taylor Service T echnician.

This unit has many sharp edges that can

cause severe injuries.

Site Preparation

Review the area where the unit will be installed before

uncrating the unit. Make sure all possible hazards to

the user or equipment have been addressed.

Air Cooled Units

DO NOT obstruct air intake and discharge openings:

Air cooled units require a minimum of 3” (76 mm) of

clearance around all sides of the freezer and 12” (305

mm) on top to allow for adequate air flow across the

condenser(s). Failure to allow adequate clearance can

reduce the refrigeration capacity of the freezer and

possibly cause permanent damage to the compressor .

For Indoor Use Only: This unit is designed to operate

indoors, under normal ambient temperatures of

70_-75_F(21_-24_C). The freezer has successfully

performed in high ambient temperatures of

104_(40_C) at reduced capacities.

This unit must NOT be installed in an area

where a water jet or hose can be used. NEVER use a

water jet or hose to rinse or clean the unit. Failure to

follow this instruction may result in electrocution.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should be

taken in moving this equipment for any reason. Two or

more persons are required to safely move this unit.

Failure to comply may result in personal injury or

equipment damage.

Uncrate the unit and inspect it for damage. Report any

damage to your Taylor Distributor.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

2

Models 8752, 8756, 8757To the Installer

101122

Water Connections

(Water Cooled Units Only)

An adequate cold water supply must be provided with

a hand shut- off valve. On the underside rear of the

base pan, two 3/8” I.P.S. (for single- head units) or two

1/2” I.P.S. (for double- head units) water connections

for inlet and outlet have been provided for easy

hook- up. 1/2” inside diameter water lines should be

connected to the machine. (Flexible lines are

recommended, if local codes permit.) Depending on

local water conditions, it may be advisable to install a

water strainer to prevent foreign substances from

clogging the automatic water valve. There will be only

one water “in” and one water “out” connection for both

single- head and double- head units. DO NOT install a

hand shut- off valve on the water “out” line! Water

should always flow in this order: first, through the

automatic water valve; second, through the

condenser; and third, through the outlet fitting to an

opentrapdrain.

A back flow prevention device is required

on the incoming water connection side. Please

refer to the applicable National, State, and local codes

for determining the proper configuration.

Electrical Conn ection s

In the United States, this equipment is intended to be

installed in accordance with the National Electrical

Code (NEC), ANSI/NFPA 70-1987. The purpose of the

NEC code is the practical safeguarding of persons and

property from hazards arising from the use of

electricity. This code contains provisions considered

necessary for safety. In all other areas of the world,

equipment should be installed in accordance with the

existing local codes. Please contact your local

authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Each unit requires one power supply for each data

label on the unit. Check the data label(s) on the freezer

for branch circuit overcurrent protection or fuse, circuit

ampacity and other electrical specifications. Refer to

the wiring diagram provided inside of the electrical box,

for proper power connections.

CAUTION: THIS EQUIPMENT MUST BE

PROPERLY GROUNDED! F AILURE TO DO SO

CAN RESULT IN SEVERE PERSONAL INJURY

FROM ELECTRICAL SHOCK!

DO NOT operate this freezer with larger fuses

than specified on the unit data label. Failure to follow

this instruction may result in electrocution or damage

to the machine.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the rear

of the frame by the authorized installer. The installation

location is marked by the equipotential bonding

symbol (5021 of IEC 60417-1) on both the removable

panel and the equipment’s frame.

Stationary appliances which are not equipped

with a power cord and a plug or another device to

disconnect the appliance from the power source must

have an all-pole disconnecting device with a contact

gap of at least 3 mm installed in the external

installation.

Appliances that are permanently connected to

fixed wiring and for which leakage currents may

exceed 10 mA, particularly when disconnected or not

used for long periods, or during initial installation, shall

have protective devices such as a GFI, to protect

against the leakage of current, installed by the

authorized personnel to the local codes.

3

Models 8752, 8756, 8757 To the Installer

130819

Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not lighter than

ordinary polychloroprene or other equivalent synthetic

elastomer-sheathed cord (Code designation 60245

IEC 57) installed with the proper cord anchorage to

relieve conductors from strain, including twisting, at

the terminals and protect the insulation of the

conductors from abrasion.

If the supply cord is damaged, it must be replaced by

the manufacturer , its service agent, or similarly

qualified person, in order to avoid a hazard.

Beater Rotatio n

Beater rotation must be clockwise as viewed

looking into the freezing cylinder.

Note: The following procedures should be

performed by a trained service technician.

To correct the rotation on a three- phase unit,

interchange any two incoming power supply lines at

freezer main terminal block only.

To correct rotation on a single- phase unit, change the

leads inside the beater motor. (Follow the diagram

printedonthemotor.)

Electrical connections are made directly to the

terminal block provided in the splice box which is

mounted on the base pan on the right side of the

freezer for the Model 8752 and located in the splice

boxes which are mounted mid- level on the frame

channel on the right and left sides for the Models 8756

and 8757.

Refrigerant

In consideration of our environment, Taylor

proudly uses only earth friendly HFC refrigerants. The

HFC refrigerant used in this unit is R404A. This

refrigerant is generally considered non-toxic and

non-flammable, with an Ozone Depleting Potential

(ODP) of zero (0).

However , any gas under pressure is potentially

hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with

liquid. Filling the cylinder to approximately 80% will

allow for normal expansion.

Use only R404A refrigerant that conforms to

the AHRI standard 700 specification. The use of any

other refrigerant may expose users and operators to

unexpected safety hazards.

Refrigerant liquid sprayed onto the skin may

cause serious damage to tissue. Keep eyes and skin

protected. If refrigerant burns should occur, flush

immediately with cold water. If burns are severe, apply

ice packs and contact a physician immediately.

Taylor reminds technicians to be cautious of

government laws regarding refrigerant recovery,

recycling, and reclaiming systems. If you have any

questions regarding these laws, please contact the

factory Service Department.

W ARNING: R404A refrigerant used in

conjunction with polyolester oils is extremely moisture

absorbent. When opening a refrigeration system, the

maximum time the system is open must not exceed 15

minutes. Cap all open tubing to prevent humid air or

water from being absorbed by the oil.

4

Models 8752, 8756, 8757To the Operator

131210

Section 2 To the Operator

The freezer you have purchased has been carefully

engineered and manufactured to give you dependable

operation. The Taylor Models 8752, 8756, and 8757

are highly sophisticated pieces of equipment, and

when properly operated and cared for, will produce a

consistent quality product. Like all mechanical

products, they will require cleaning and maintenance.

A minimum amount of care and attention is necessary

if the operating procedures outlined in this manual are

followed closely.

This Operator’s Manual should be read

before operating or performing any maintenance on

your equipment.

Your freezer will NOT eventually compensate and

correct for any errors during the set- up or filling

operations. Thus, the initial assembly and priming

procedures are of extreme importance. It is strongly

recommended that all personnel responsible for the

equipment’ s operation study these procedures

together in order to be properly trained and to make

sure that no misunderstandings exist.

In the event you should require technical assistance,

please contact your local authorized Taylor Distributor.

Note: Your Taylor warranty is valid only if the parts are

authorized Taylor parts, purchased from the local

authorized Taylor Distributor, and only if all required

service work is provided by an authorized Taylor

service technician. Taylor reserves the right to deny

warranty claims on units or parts if non- Taylor

approved parts or incorrect refrigerant were installed

in the unit, system modifications were performed

beyond factory recommendations, or it is determined

that the failure was caused by abuse, misuse, neglect,

or failure to follow all operating instructions. For full

details of your Taylor Warranty, please see the Limited

W arranty section in this manual.

Note: Constant research results in steady

improvements; therefore, information in this

manual is subject to change without notice.

If the crossed out wheeled bin symbol is

affixed to this product, it signifies that this product is

compliant with the EU Directive as well as other similar

legislation in effect after August 13, 2005. Therefore,

it must be collected separately after its use is

completed, and cannot be disposed as unsorted

municipal waste.

The user is responsible for returning the product to the

appropriate collection facility, as specified by your local

code.

For additional information regarding applicable local

laws, please contact the municipal facility and/or local

distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are

warranted for the term stated in the Limited Warranty

section in this manual. However, due to the Montreal

Protocol and the U.S. Clean Air Act Amendments of

1990, many new refrigerants are being tested and

developed, thus seeking their way into the service

industry. Some of these new refrigerants are being

advertised as drop- in replacements for numerous

applications. It should be noted that in the event of

ordinary service to this unit’s refrigeration system,

only the refrigerant specified on the affixed data

label should be used. The unauthorized use of

alternate refrigerants will void your Taylor compressor

warranty. It is the unit owner’s responsibility to make

this fact known to any technician he employs.

It should also be noted that Taylor does not warrant the

refrigerant used in its equipment. For example, if the

refrigerant is lost during the course of ordinary service

to this machine, Taylor has no obligation to either

supply or provide its replacement either at billable or

unbillable terms. Taylor does have the obligation to

recommend a suitable replacement if the original

refrigerant is banned, obsoleted, or no longer available

during the five year warranty of the compressor.

The Taylor Company will continue to monitor the

industry and test new alternates as they are being

developed. Should a new alternate prove, through our

testing, that it would be accepted as a drop- in

replacement, then the above disclaimer would

become null and void. To find out the current status of

an alternate refrigerant as it relates to your

compressor warranty, call the local Taylor Distributor

or the Taylor Factory. Be prepared to provide the

Model/Serial Number of the unit in question.

5

Models 8752, 8756, 8757 Safety

130211

Section 3 Safety

We, at Taylor Company, are concerned about the

safety of the operator when he or she comes in contact

with the freezer and its parts. Taylor has gone to

extreme efforts to design and manufacture built- in

safety features to protect both you and the service

technician. As an example, warning labels have been

attached to the freezer to further point out safety

precautions to the operator .

IMPORTANT - Failure to adhere to the

following safety precautions may result in severe

personal injury or death. Failure to comply with

these warnings may damage the machine and its

components. Component damage will result in

part replacement expense and service repair

expense.

DO NOT operate the freezer without reading

this Operator Manual. Failure to follow this instruction

may result in equipment damage, poor freezer

performance, health hazards, or personal injury.

This appliance is to be used only by trained

personnel. It is not intended for use by children or

people with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge,

unless given supervision or instruction concerning the

use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that

they do not play with the appliance.

This unit is provided with an equipotential

grounding lug that is to be properly attached to the rear

of the frame by the authorized installer. The installation

location is marked by the equipotential bonding

symbol (5021 of IEC 60417-1) on both the removable

panel and the equipment’s frame.

DO NOT use a water jet to clean or rinse the

freezer. Failure to follow these instructions may result

in serious electrical shock.

S DO NOT operate the freezer unless it is

properly grounded.

S DO NOT operate the freezer with larger fuses

than specified on the freezer data label.

S All repairs must be performed by an

authorized Taylor service technician.

S The main power supplies to the machine must

be disconnected prior to performing any

repairs.

S For Cord Connected Units: Only Taylor

authorized service technicians or licensed

electricians may install a plug or replacement

cord on these units.

S Stationary appliances which are not equipped

with a power cord and a plug or another device

to disconnect the appliance from the power

source, must have an all-pole disconnecting

device with a contact gap of at least 3 mm

installed in the external installation.

S Stationary appliances which are not equipped

with a power cord and a plug or another device

to disconnect the appliance from the power

source must have an all-pole disconnecting

device with a contact gap of at least 3 mm

installed in the external installation.

S Appliances that are permanently connected to

fixed wiring and for which leakage currents

may exceed 10 mA, particularly when

disconnected or not used for long periods, or

during initial installation, shall have protective

devices such as a GFI, to protect against the

leakage of current, installed by the authorized

personnel to the local codes.

6

Models 8752, 8756, 8757Safety

130819

S Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not

lighter than ordinary polychloroprene or other

equivalent synthetic elastomer-sheathed cord

(Code designation 60245 IEC 57) installed

with the proper cord anchorage to relieve

conductors from strain, including twisting, at

the terminals and protect the insulation of the

conductors from abrasion.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent, or similarly qualified person, in order to

avoid a hazard.

Failure to follow these instructions may result in

electrocution. Contact your local authorized Taylor

Distributor for service.

S DO NOT allow untrained personnel to operate

this machine.

S DO NOT operate the freezer unless all service

panels and access doors are restrained with

screws.

S DO NOT remove any internal operating parts

(example: freezer door , beater, scraper

blades, etc.) unless all control switches are in

the OFF position.

Failure to follow these instructions may result in severe

personal injury from hazardous moving parts.

This unit has many sharp edges that can

cause severe injuries.

S DO NOT put objects or fingers in the door

spout. This may contaminate the product and

cause severe personal injury from blade

contact.

S USE EXTREME CAUTION when removing

the beater asssembly. The scraper blades are

very sharp.

This freezer must be placed on a level

surface. Failure to comply may result in personal injury

or equipment damage.

Access to the service area of the unit is

restricted to persons having knowledge and practical

experience with the appliance, in particular as far as

safety and hygiene are concerned.

Cleaning and sanitizing schedules are

governed by your state or local regulatory agencies

and must be followed accordingly. Please refer to the

cleaning section of this manual for the proper

procedure to clean this unit.

This machine is designed to maintain product

temperature under 41_F(5_C). Any product being

added to this machine must be below 41_F(5_C).

Failure to follow this instruction may result in health

hazards and poor freezer performance.

DO NOT run the unit without product. Failure to follow

this instruction can result in damage to the unit.

DO NOT obstruct air intake and discharge openings:

Air cooled units require a minimum of 3” (76 mm) of

clearance around all sides of the freezer and 12” (305

mm) on top to allow for adequate air flow across the

condenser(s). Failure to allow adequate clearance can

reduce the refrigeration capacity of the freezer and

possibly cause permanent damage to the compressor .

For Indoor Use Only: This unit is designed to operate

indoors, under normal ambient temperatures of 70_ -

75_F(21_ -24_C). The freezer has successfully

performed in high ambient temperatures of

104_(40_C) at reduced capacities.

NOISE LEVEL: Airborne noise emission does not

exceed 78 dB(A) when measured at a distance of 1.0

meter from the surface of the machine and at a height

of 1.6 meters from the floor.

7

Models 8752, 8756, 8757 Operator Parts Identification

130117

Section 4 Operator Parts Identification

Model 8752

8

Models 8752, 8756, 8757Operator Parts Identification

111129

8752 Parts Identification

Item Description Part No.

1 Panel A.- Front X22997

2 Stud- Nose Cone 022822

3 Bolt- Carriage 012347

4 Panel A.- Lower Side (R & L) X23956

5 Panel- Upper Side Left 028599

6 Hood 050464

7 Panel- Upper Rear 022074

8 Panel- Lower Rear 025128

9 Panel- Upper Side Right 028600

10 Pan- Drip 11 - 5/8” Long 027503

11 Caster- Swivel 3/4 - 10, 3” Wheel 021279

12 Gasket- Cabinet Mix Door 020134

13 Probe A. - Mix X35981

14 Boot- Mix Cover 037200

15 Tank- Mix 020275

Item Description Part No.

16 Funnel- Mix 036637

17 Cover A. - Mix Tank X38726

18 Tray- Drip 16- 7/8 x 5- 1/8 020157

19 Shield- Splash 23” Long 022765

20 Cover- Mix Storage - Center

Single

038827

21 Trim- Rear Corner 022071

22 Trim A.- Upper Side Left/Right X22423

23 Trim A.- Shelf X20426

24 Trim- Front- Left 024824- SP

25 Trim- Front- Right 024825

26 Trim- Bottom Mix Door 024974

27 Trim- Mix Door 024976

28 Caster- 3” SWV 3/4- 10 Stem

w/Brake

030307

9

Models 8752, 8756, 8757 Operator Parts Identification

130116

8752 Beater Door Assembly

10

Models 8752, 8756, 8757Operator Parts Identification

130116

8752 Beater Door Parts Identification

Item Description Part No.

1 Seal- Drive Shaft 032560

2 Shaft- Beater 032564

3 Beater A.- 3.4 Qt. 1 Pin X46231

4 Clip- Scraper Blade 046236

5 Blade- Scraper- Plastic 046235

6 Kit A.- Beater- Front Shoes- Brg X50350

*6a Bearing- Front *See note

*6b Shoe- Front Helix - Front *See note

*6c Shoe- Front Helix - Rear *See note

7 Gasket- Door HT 4” Double 048926

8 Door A.- 1 Spout Long Baffle X51531- 10

8a Door A.- Magnet X68625- 2

8b Baffle A.- Long 4” X50882

Item Description Part No.

9 Handle A.- Draw - Adjustable X55096

9a Handle- Adjustable 028804

9b Screw- Adjustment 055092

9c O - Ring (Adj. Screw) 015872

9d Nut- Ja m 5/16- 24 029639- BLK

10 O- Ring - 5/16 OD x .070 W 016272

11 Pin A.- Pivot X22820

12 Nut- Stud 021508

13 Valve A.- Draw X18303

14 O- Ring - 7/8 OD x .103 W 014402

15 Cap- Design - 1.010” ID 014218

16 Plug - P rime 028805

17 O- Ring - 3/8 OD x .070 W 016137

*Order as X50350 only.

11

Models 8752, 8756, 8757 Operator Parts Identification

111129

Model 8756

12

Models 8752, 8756, 8757Operator Parts Identification

111129

8756 Parts Identification

Item Description Part No.

1 Panel A.- Front X22879

2 Stud- Nose Cone 022822

3 Bolt- Carriage 012347

4 Panel A.- Lower Side (R & L) X23956

5 Panel- Upper Side Left 028599

6 Hood 048526

7 Panel- Upper Rear 022015

8 Panel- Lower Rear 023598

9 Panel- Upper Side Right 028600

10 Pan- Drip 17- 1/4” Long 027504

11 Caster- Swivel 3/4- 10, 3” Wheel 021279

12 Gasket- Cabinet Mix Door 024629

13 Probe A.- Mix (2) X35981

14 Boot- Mix Cover 037200

15 Tank A.- Mix w/Decals X38755

15a Tank (only) 034928

Item Description Part No.

16 Cover- Mix Tank 024590

17 Funnel- Mix 036637

18 Tray- Drip 22- 7/8 x 5- 1/8 014533

19 Shield- Splash 23” Long 022766

20 Cover- Left Mix Storage 037138

21 Cover- Right Mix Storage 037139

22 Trim- Corner- Left/Right 022013

23 Trim A.- Side Left/Right X22424

24 Trim A.- Shelf X24813

25 Trim - Front- Left 024824- SP

26 Trim - Front- Right 024825

27 Trim - Bottom Cabinet 024826

28 Strip- Top Trim 024827

29 Caster- 3” Swv 3/4- 10 Stem

w/Brake

030307

13

Models 8752, 8756, 8757 Operator Parts Identification

Model 8757

14

Models 8752, 8756, 8757Operator Parts Identification

111129

8757 Parts Identification

Item Description Part No.

1 Panel A.- Front X36711

2 Stud - Nose Cone 022822

3 Bolt- Carriage 1/4 - 20 x 3/4 012347

4 Panel A.- Lower Side - L/R X36741

5 Panel- Upper Side Left 028599

6 Hood 048526

7 Panel- Upper Rear 042068

8 Panel- Lower Rear 042067

9 Panel- Upper Side Right 028600

10 Pan- Drip 036232

11 Caster- Swivel 3/4 - 10 ST 021279

12 Gasket- Cabinet- Mix Door 024629

13 Probe A. - Mix X35981

14 Boot- Mix Cover 037200

15 Tank- Mix X38755

15a Tank (only) 034928

Item Description Part No.

16 Cover- Mix Tank 024590

17 Funnel- Mix 036637

18 Tray- Drip 014533

19 Shield- Splash 23” Long 022766

20 Cover- Mix Storage Left 037138

21 Cover- Mix Storage Right 037139

22 Trim- Rear Corner- Left/Right 036740

23 Trim A.- Side Left/Right X22424

24 Trim A.- Shelf X36732

25 Trim- Front- Left 024824- SP

26 Trim- Front- Right 024825

27 Trim- Bottom Cabinet 024826

28 Strip- Top Trim 024827

29 Caster- 3” Swv 3/4- 10 Stem

w/Brake

030307

15

Models 8752, 8756, 8757 Operator Parts Identification

8756 & 8757 Beater Door Assembly

Item Description Part No.

1 Seal- Drive Shaft 032560

2 Shaft- Beater 032564

3 Beater A.- 3.4 Qt. 1 Pin X46231

4 Clip- Scraper Blade 046236

5 Blade- Scraper- Plastic 046235

*6a Bearing - Front 050348

*6b Shoe- Front Helix - Rear 050346

*6c Shoe- Front Helix- Front 050347

7 Gasket- Door 4” Double 048926

8 Door A.- 3 Spout Long Baffle X51532- 12

9 Handle A.- Draw- Adj. X33687

9a Draw Handle- Adj. 028804

9b Screw- Adjustment 033662

Item Description Part No.

9c O - Ring (Adj. Screw) 015872

9d Nut- Ja m 5/16- 24 029639- BLK

10 O- Ring - 5/16 OD x .070 W 016272

11 Rod A.- Pivot X22387

12 Nut- Stud (Long) 034382

13 Valve A.- Draw (3) X18303

14 O- Ring - 7/8 OD x .103 W (6) 014402

15 Cap- Design - 1.010” ID 014218

16 Nut- Stud (Short) 034383

17 Rod A.- Pivot X22388

18 Plug- Prime (2) 028805

19 O- Ring - 3/8 OD x .070 W (4) 016137

*Order Kit X50350

16

Models 8752, 8756, 8757Operator Parts Identification

140814

Accessories

Item Description Part No.

1 Brush - Mix Pump Body 023316

2 Brush - Pressure Switch 027647

3 Brush - Feed Tube 021101

4 Brush - Double Ended 013072

5 Brush- Rear Bearing 013071

6 Brush- Draw Valve 013073

7 Lubricant- Taylor 4 oz. 047518

Item Description Part No.

8 Sanitizer- Kay- 5 *See note

9 Pail- 10 Qt. 013163

10

Kit A.- Tune Up (Model 8752) X49463- 15

Kit A.- Tune Up

(Models 8756 & 8757)

X49463- 2

11 Sanitizer- Stera Sheen- Green

(8752, 8756, 8757)

*See note

*Note: A sample container of sanitizer is sent with the

unit. For reorders, order Stera Sheen part no. 055492

(100 2 oz. packs) or Kay - 5 part no. 041082 (200 packs).

Page is loading ...

Taylor 8757 User manual

This manual is also suitable for

Taylor 8757 User manual

Related papers

Other documents