ASRock Rack ROMED4ID-2T User manual

ROMED4ID-2T

User Manual

Version 1.0

Published January 2021

Version 1.0 (HW R1.02)

Published March 2023

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated

in any language, in any form or by any means, except duplication of documentation by the

purchaser for backup purpose, without written consent of ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not be

registered trademarks or copyrights of their respective companies, and are used only for

identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock Rack. ASRock Rack assumes no responsibility

for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to the implied

warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for loss of

prots, loss of business, loss of data, interruption of business and the like), even if ASRock

Rack has been advised of the possibility of such damages arising from any defect or error

in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

is equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. ese limits are designed to provide

reasonable protection against harmful interference in a residential installation. is

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and compensation for

any other reasonably foreseeable loss or damage caused by our goods. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure. If you require assistance please call ASRock

Rack Tel : +886-2-55599600 ext.123 (Standard International call charges apply)

ASRock Rack INC. hereby declares that this device is in compliance with the essential

requirements and other relevant provisions of related UKCA Directives. Full text of UKCA

declaration of conformity is available at: http://www.asrockrack.com

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related Directives. Full text of EU declaration

of conformity is available at: http://www.asrockrack.com

ASRock Rack follows the green design concept to design and manufacture our products,

and makes sure that each stage of the product life cycle of ASRock Rack product is in line

with global environmental regulations. In addition, ASRock Rack disclose the relevant

information based on regulation requirements.

Please refer to https://www.asrockrack.com/general/about.asp?cat=Responsibility for

information disclosure based on regulation requirements ASRock Rack is complied with:

DO NOT throw the motherboard in municipal waste. is product has been

designed to enable proper reuse of parts and recycling. is symbol of the

crossed out wheeled bin indicates that the product (electrical and electronic

equipment) should not be placed in municipal waste. Check local regulations

for disposal of electronic products.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 5

1.4 Motherboard Layout 6

1.5 Onboard LED Indicators 8

1.6 I/O Panel 10

1.7 Block Diagram 12

Chapter 2 Installation 13

2.1 Screw Holes 13

2.2 Pre-installation Precautions 13

2.3 Installing the CPU 14

2.4 Installation of Memory Modules (DIMM) 18

2.5 Expansion Slot (PCI Express Slot) 20

2.6 Onboard Headers and Connectors 21

2.7 ATX PSU / DC-IN Power Connections 27

2.8 Unit Identication purpose LED/Switch 28

2.9 M.2 SSD Module Installation Guide 29

Chapter 3 UEFI Setup Utility 30

3.1 Introduction 30

3.1.1 UEFI Menu Bar 30

3.1.2 Navigation Keys 31

3.2 Main Screen 32

3.3 Advanced Screen 33

3.3.1 CPU Conguration 34

3.3.2 Chipset Conguration 35

3.3.3 Storage Conguration 37

3.3.4 ACPI Conguration 38

3.3.5 USB Conguration 39

3.3.6 Super IO Conguration 40

3.3.7 Serial Port Console Redirection 41

3.3.8 H/W Monitor 44

3.3.9 PCI Subsystem Settings 45

3.3.10 AMD CBS 46

3.3.11 AMD PBS 47

3.3.12 PSP Firmware Versions 48

3.3.13 Instant Flash 49

3.4 Server Mgmt 50

3.4.1 System Event Log 51

3.4.2 BMC Network Conguration 52

3.4.3 BMC Tools 54

3.5 Security 55

3.5.1 Key Management 56

3.6 Boot Screen 59

3.6.1 CSM Parameters 61

3.7 Event Logs 64

3.8 Exit Screen 66

Chapter 4 Software Support 67

4.1 Download and Install Operating System 67

4.2 Download and Install Software Drivers 67

4.3 Contact Information 67

Chapter 5 Troubleshooting 68

5.1 Troubleshooting Procedures 68

5.2 Technical Support Procedures 70

5.3 Returning Merchandise for Service 70

ROMED4ID-2T

PB 1

English

Chapter 1 Introduction

ank you for purchasing ASRock Rack ROMED4ID-2T motherboard, a reliable

motherboard produced under ASRock Rack’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock Rack’s commitment to

quality and endurance.

In this manual, chapter 1 and 2 contains introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contains the conguration guide to BIOS

setup and information of the Soware Support.

1.1 Package Contents

•ASRock Rack ROMED4ID-2T Motherboard

(Proprietary Form Factor: 6.7-in x 8.2-in, 17 cm x 20.8 cm)

•Quick Installation Guide

•1 x I/O Shield

•1 x ATX 4P to 24P Power Cable (8cm)

•1 x SATA Power Cable (80cm)

•1 x M.3 umb Screw without Screwdriver for M.2 Socket

If any items are missing or appear damaged, contact your authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. You may nd the latest memory and CPU support lists on ASRock Rack

website as well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard, please visit our website for

specic information about the model you are using.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

ROMED4ID-2T

MB Physical Status

Form Factor Proprietary

Dimension 6.7'' x 8.2'' (17.0 cm x 20.8 cm)

Processor System

CPU AMD EPYC™ 7002* Series Processors Family

*Please refer to CPU AVL on the ASRock Rack’s website for latest update.

Socket Single Socket SP3 (LGA4094)

Chipset N/A

System Memory

Type - Quad Channel DDR4 memory technology (1DPC)

- Supports DDR4 RDIMM, LRDIMM, 3DS, and NVDIMM

DIMM Size Per

DIMM

- RDIMM: 64GB, 32GB, 16GB, 8GB

- LRDIMM: 256GB, 128GB, 64GB, 32GB

- 3DS: 32GB, 16GB, 8GB

- NV DIMM: 32GB

DIMM Frequency - RDIMM: 3200MHz

- LRDIMM: 3200MHz

- 3DS: 3200MHz

- NVDIMM: 2666MHz

Voltage 1.2V

Expansion Slot

PCIe 4.0 x 16 PCIE7: Gen4 x16 link

Storage

SlimSAS 2 Low-Prole SlimSAS (PCIe4.0 x8 or 8 SATA 6Gb/s)

4 SlimSAS (PCIe4.0 x8)

RAID Support N/A

M.2 Slot 1 (M2_1: 2280, 1 M-key (SATA 6Gb/s or PCIe4.0 x4)

Ethernet

Interface 10000/1000 /100 Mbps by Intel X550

LAN Controller - 2 x RJ45 10G base-T by Intel® X550-AT2

- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN1 supports NCSI

Management

BMC Controller ASPEED AST2500

IPMI Dedicated

GLAN

1 x Realtek RTL8211E for dedicated management GLAN

ROMED4ID-2T

2 3

English

Features Watch Dog

NMI

Graphics

Controller ASPEED AST2500

Rear Panel I/O

VGA Port 1 x D-Sub

USB 3.2 Gen1 Port 2

LAN Port - 2 RJ45 (10GbE) + 1 dedicated IPMI

- LAN Ports with LED (ACT/LINK LED and SPEED LED)

UID 1

Internal Connector

Auxiliary Panel

Header

1 (includes chassis intrusion, location button & LED, and front

LAN LED)

TPM Header 1

IPMB Header 1

Fan Header 3 Fans x 4-pin

ATX Power 1 x (8-pin) + 1 x (8-pin) + 1 x (4-pin) + 1 x (4-pin)

USB 2.0 Header 1 (supports 2 USB 2.0 ports)

M.2 1 (M2_1: 2280 (SATA 6Gb/s or PCIe4.0 x4))

SlimSAS 6

PSU SMB 1

Smbus from BMC 1

ermal Sensor

Header

1

Speaker(4pin) 1

ClearCMOS 1 (short pad)

CPU1_HSBP1 1

OH/FanFail LED 3 (only Fan Fail LED)

COM Header 1

System BIOS

BIOS Type 32MB AMI UEFI Legal BIOS

BIOS Features - Plug and Play (PnP)

- ACPI 2.0 Compliance Wake Up Events

- SMBIOS 2.8 Support

- ASRock Rack Instant Flash

Hardware Monitor

Temperature - CPU Temperature Sensing

- MB/TR1/Card side Temperature Sensing

Fan - Fan Tachometer

- CPU Quiet Fan (Allow CPU Fan Speed Auto-Adjust by CPU

Temperature)

- Fan Multi-Speed Control

Voltage Voltage Monitoring: Vsoc,Vcpu, VCCM, VPPM, 3V/5V/12V,

+BAT, 3VSB, 5VSB

4 5

English

Support OS

OS Microso® Windows®

- Server 2016 (64 bit)

- Server 2019 (64 bit)

Linux®

- RedHat Enterprise Linux Server 8.2 (64 bit) / 7.9 (64 bit)

- CentOs 8.2 (64 bit) / 7.9 (64 bit)

- SUSE SLES 15.2 (64 bit) / 12.5 (64 bit)

- UBuntu 20.04.1 (64 bit) / 18.04.5 (64 bit) / 16.04.7 (64 bit)

Hypervisor

- VMWare ESXi 6.7 u3 / 7.0 u1

- vSphere 6.7 u3 / 7.0 u1

- CITRIX Hypervisor 8.1.0

* Please refer to our website for the latest OS support list.

Environment

Temperature Operation temperature: 10°C ~ 35°C / Non operation

temperature: -40°C ~ 70°C

NOTE: Please refer to our website for the latest specications.

is motherboard supports Wake from on Board LAN. To use this function, please make

sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager

> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is

enabled in UEFI SETUP UTILITY > Advanced > ACPI Conguration. Aer that, onboard

LAN1&2 can wake up S5 under OS.

If you install Intel® LAN utility or Marvell SATA utility, this motherboard may fail Win-

dows® Hardware Quality Lab (WHQL) certication tests. If you install the drivers only, it

will pass the WHQL tests.

ROMED4ID-2T

4 5

English

1.3 Unique Features

ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is con-

venient BIOS update tool allows you to update system BIOS without entering operat-

ing systems rst like MS-DOS or Windows®. With this utility, you can press the <F6>

key during the POST or the <F2> key to enter into the BIOS setup menu to access

ASRock Rack Instant Flash. Just launch this tool and save the new BIOS le to your

USB ash drive, oppy disk or hard drive, then you can update your BIOS only in a

few clicks without preparing an additional oppy diskette or other complicated ash

utility. Please be noted that the USB ash drive or hard drive must use FAT32/16/12

le system.

6 7

English

1.4 Motherboard Layout

20.8cm (8.2 in)

VGA1

DDR4_G1 (64 bit, 288-pin module)

DDR4_H1 (64 bit, 288-pin module)

ATX12V2

USB 3.2 Gen 1

T: USB2

B: USB1

IPMI_LAN

LAN1

UID1

PCIE7

M2_1

NUT80

HDLED RESET

PLED PWRBTN

PANEL1

1

TPM1

1

SPEAKER1

1

T 1

R

1

IPMB1

1

AST

2500

ATX12V1

BMC

F/W

LGA4094

Socket SP3

PSU_SMB1

(NCSI)

1

LAN2

DDR4_D1 (64 bit, 288-pin module)

DDR4_C1 (64 bit, 288-pin module)

FAN1

BATTERY1

SATAPWR1

ATX4PIN1

FAN2

FAN3

USB_1_2

1

ITX_AUX_PANEL1

PWM_CFG1

NMI_BTN1

SLIM1

SLIM2

SLIM3

SLIM4

SLIM5

SLIM6

17Cm (6.7 in)

123456

7

8

9

10

11

12

13

14

15

17

18

24

23

22

21

20 19

25

272829

30

CLRMOS1

26

1

COM1

1

CPU1_HSBP1

BMC_SMB1

16

ROMED4ID-2T

6 7

English

No. Description

1 System Fan Connector (FAN1)

2 PSU SMBus Header (PSU_SMB1)

3 SATA Power Connector (DC-IN Mode) (SATAPWR1)**

4 ATX 4-PIN Power Connector (ATX4PIN1)**

5 ATX 12V Power Connector (ATX12V2)

6 ATX 12V Power Connector (ATX12V1)

7 Low-Prole Slimline SAS Connector (SLIM1) (Supports SATA)

8 Low-Prole Slimline SAS Connector (SLIM2) (Supports SATA)

9 2 x 288-pin DDR4 DIMM Slots (DDR4_G, DDR4_H1)*

10 Slimline SAS Connector (SLIM3)

11 Slimline SAS Connector (SLIM4)

12 Slimline SAS Connector (SLIM5)

13 2 x 288-pin DDR4 DIMM Slots (DDR4_C1, DDR4_D1)*

14 Slimline SAS Connector (SLIM6)

15 TPM Header (TPM1)

16 BMC SMBus Header (BMC_SMB1)

17 Speaker Header (SPEAKER1)

18 PWM Conguration Header (PWM_CFG1)

19 System Panel Header (PANEL1)

20 Auxiliary Panel Header (ITX_AUX_PANEL1)

21 Non Maskable Interrupt Button (NMI_BTN1)

22 Clear CMOS Pad (CLRMOS1)

23 USB 2.0 Header (USB_1_2)

24 Backplane PCI Express Hot-Plug Connector (CPU1_HSBP1)

25 COM Port Header (COM1)

26 System Fan Connector (FAN3)

27 System Fan Connector (FAN2)

28 ermal Sensor Header (TR1)

29 Intelligent Platform Management Bus Header (IPMB1)

30 M.2 Socket (M2_1) (Type 2280)

*For DIMM installation and conguration instructions, please see p.21 (Installation of Memory Modules

(DIMM)) for more details.

**Caution: Misconnection between the ATX4PIN1 and the SATAPWR1 connectors may permanently damage the

motherboard.

8 9

English

1.5 Onboard LED Indicators

DDR4_G1 (64 bit, 288-pin module)

DDR4_H1 (64 bit, 288-pin module)

LGA4094

Socket SP3

DDR4_C1 (64 bit, 288-pin module)

DDR4_D1 (64 bit, 288-pin module)

1 2

43

5

1

ROMED4ID-2T

8 9

English

No. Item Status Description

1FAN_LED1 Amber FAN1 failed

2 SB_PWR1 Green STB PWR ready

3FAN_LED3 Amber FAN3 failed

4FAN_LED2 Amber FAN2 failed

5BMC_LED1 Green BMC heartbeat LED

10 11

English

1.6 I/O Panel

1

2

3

4

5

6

No. Description No. Description

1 USB 3.2 Gen1 Ports (USB3_1_2) 4 VGA Port (VGA1)

2 LAN RJ-45 Port (IPMI_LAN1)* 5 10G LAN RJ-45 Port (LAN1)**

3 UID Switch (UID1) 6 10G LAN RJ-45 Port (LAN2)**

*ere are two LED next to the LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M bps connection or no

link

Blinking Yellow Data Activity Yel low 100M bps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

ROMED4ID-2T

10 11

English

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

10G LAN Port (LAN1, LAN2) LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 100Mbps connection or

no link

Blinking Yellow Data Activity Yellow 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

SPEED LED

ACT/LINK LED

12 13

English

1.7 Block Diagram

ROMED4ID-2T

12 13

English

Chapter 2 Installation

This is a Proprietary form factor (6.7'' x 8.2'', 17.0 cm x 20.8 cm) motherboard. Before

you install the motherboard, study the conguration of your chassis to ensure that the

motherboard ts into it.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components or

change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any components.

2. To avoid damaging the motherboard’s components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use a

grounded wrist strap or touch a safety grounded object before you handle the compo-

nents.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-static pad or in

the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis,

please do not over-tighten the screws! Doing so may damage the motherboard.

Make sure to unplug the power cord before installing or removing the motherboard. Failure

to do so may cause physical injuries to you and damages to motherboard components.

Do not over-tighten the screws! Doing so may damage the motherboard.

Before you install or remove any component, ensure that the power is switched o or the

power cord is detached from the power supply. Failure to do so may cause severe damage to

the motherboard, peripherals, and/or components.

14 15

English

2.3 Installing the CPU

1. Before you insert the CPU into the socket, please check if the PnP cap is on the socket,

if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to

insert the CPU into the socket if above situation is found. Otherwise, the CPU will be

seriously damaged.

2. Unplug all power cables before installing the CPU.

1

2

Page is loading ...

ASRock Rack ROMED4ID-2T User manual

ASRock Rack ROMED4ID-2T User manual

Related papers

Other documents