ASRock Rack ROMED8U-2T User manual

ROMED8U-2T

ROMED8U-2T/BCM

User Manual

Version 1.0

Published August 2022

Version 1.0

Published March 2023

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or translated

in any language, in any form or by any means, except duplication of documentation by the

purchaser for backup purpose, without written consent of ASRock Rack Inc.

Products and corporate names appearing in this documentation may or may not be

registered trademarks or copyrights of their respective companies, and are used only for

identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock Rack. ASRock Rack assumes no responsibility

for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock Rack does not provide

warranty of any kind, either expressed or implied, including but not limited to the implied

warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock Rack, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for loss of

prots, loss of business, loss of data, interruption of business and the like), even if ASRock

Rack has been advised of the possibility of such damages arising from any defect or error

in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

is equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. ese limits are designed to provide

reasonable protection against harmful interference in a residential installation. is

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and compensation for

any other reasonably foreseeable loss or damage caused by our goods. You are also entitled

to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure. If you require assistance please call ASRock

Rack Tel : +886-2-55599600 ext.123 (Standard International call charges apply)

ASRock Rack INC. hereby declares that this device is in compliance with the essential

requirements and other relevant provisions of related UKCA Directives. Full text of UKCA

declaration of conformity is available at: http://www.asrockrack.com

ASRock Rack INC. hereby declares that this device is in compliance with the essential re-

quirements and other relevant provisions of related Directives. Full text of EU declaration

of conformity is available at: http://www.asrockrack.com

ASRock Rack follows the green design concept to design and manufacture our products,

and makes sure that each stage of the product life cycle of ASRock Rack product is in line

with global environmental regulations. In addition, ASRock Rack disclose the relevant

information based on regulation requirements.

Please refer to https://www.asrockrack.com/general/about.asp?cat=Responsibility for

information disclosure based on regulation requirements ASRock Rack is complied with:

DO NOT throw the motherboard in municipal waste. is product has been

designed to enable proper reuse of parts and recycling. is symbol of the

crossed out wheeled bin indicates that the product (electrical and electronic

equipment) should not be placed in municipal waste. Check local regulations

for disposal of electronic products.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Unique Features 6

1.4 Motherboard Layout 7

1.5 Onboard LED Indicators 10

1.6 I/O Panel 12

1.7 Block Diagram 14

Chapter 2 Installation 16

2.1 Screw Holes 16

2.2 Pre-installation Precautions 16

2.3 Installing the CPU 17

2.4 Installation of Memory Modules (DIMM) 21

2.5 Expansion Slots (PCI Express Slots) 23

2.6 Onboard Headers and Connectors 24

2.7 ATX PSU / DC-IN Power Connections 30

2.8 Unit Identication purpose LED/Switch 31

2.9 M.2 SSD Module Installation Guide (M2_1) 32

Chapter 3 UEFI Setup Utility 33

3.1 Introduction 33

3.1.1 UEFI Menu Bar 33

3.1.2 Navigation Keys 34

3.2 Main Screen 35

3.3 Advanced Screen 36

3.3.1 CPU Conguration 37

3.3.2 Chipset Conguration 38

3.3.3 Storage Conguration 40

3.3.4 ACPI Conguration 41

3.3.5 USB Conguration 42

3.3.6 Super IO Conguration 43

3.3.7 Serial Port Console Redirection 44

3.3.8 H/W Monitor 47

3.3.9 PCI Subsystem Settings 48

3.3.10 AMD CBS 49

3.3.11 AMD PBS 50

3.3.12 PSP Firmware Versions 51

3.3.13 Instant Flash 52

3.4 Server Mgmt 53

3.4.1 System Event Log 54

3.4.2 BMC Network Conguration 55

3.4.3 BMC Tools 57

3.5 Security 58

3.5.1 Key Management 59

3.6 Boot Screen 62

3.6.1 CSM Parameters 64

3.7 Event Logs 66

3.8 Exit Screen 68

Chapter 4 Software Support 69

4.1 Download and Install Operating System 69

4.2 Download and Install Software Drivers 69

4.3 Contact Information 69

Chapter 5 Troubleshooting 70

5.1 Troubleshooting Procedures 70

5.2 Technical Support Procedures 72

5.3 Returning Merchandise for Service 72

ROMED8U-2T

ROMED8U-2T/BCM

PB 1

English

Chapter 1 Introduction

ank you for purchasing ASRock Rack ROMED8U-2T / ROMED8U-2T/BCM

motherboard, a reliable motherboard produced under ASRock Rack’s consistently stringent

quality control. It delivers excellent performance with robust design conforming to ASRock

Rack’s commitment to quality and endurance.

In this manual, chapter 1 and 2 contains introduction of the motherboard and step-by-step

guide to the hardware installation. Chapter 3 and 4 contains the conguration guide to BIOS

setup and information of the Support CD.

1.1 Package Contents

• ASRock Rack ROMED8U-2T / ROMED8U-2T/BCM Motherboard

(micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)

• Quick Installation Guide

• 1 x I/O Shield

• 1 x Mini SAS HD to 4*SATA Cable (60cm)

• 1 x ATX 4P to 24P Power Cable (8cm)

• 1 x SATA 6P to 15P Power Cable (80cm)

• 1 x SATA3 Cable (60cm)

• 1 x Screw for M.2 Socket

If any items are missing or appear damaged, contact your authorized dealer.

Because the motherboard specications and the BIOS soware might be updated, the con-

tent of this manual will be subject to change without notice. In case any modications of

this manual occur, the updated version will be available on ASRock Rack website without

further notice. You may nd the latest memory and CPU support lists on ASRock Rack

website as well. ASRock Rack’s Website: www.ASRockRack.com

If you require technical support related to this motherboard, please visit our website for

specic information about the model you are using.

http://www.asrockrack.com/support/

2 3

English

1.2 Specications

ROMED8U-2T / ROMED8U-2T/BCM

MB Physical Status

Form Factor micro ATX

Dimension 9.6'' x 9.6'' (24.4 cm x 24.4 cm)

Processor System

CPU AMD EPYC™7003 and 7002Series Processors

Socket Single Socket P+ (LGA4094)

Max. ermal

Design Power

(TDP)

280W

Chipset System on chip

System Memory

Type - Eight Channel DDR4 memory technology (1DPC)

- Supports DDR4 RDIMM/ RDIMM-3DS/ LRDIMM/

LRDIMM-3DS/NVDIMM

DIMM Size Per

DIMM

- RDIMM: 64GB, 32GB, 16GB, 8GB

- RDIMM-3DS: 256GB, 128GB, 64GB, 32GB, 16GB, 8GB

- LRDIMM: 128GB, 64GB, 32GB

- LRDIMM-3DS: 256GB, 128GB, 64GB, 32GB, 16GB, 8GB

- NVDIMM: 32GB

*Max. memory capacity and frequency are to be validated

DIMM Frequency - RDIMM: 3200MHz

- LRDIMM: 3200MHz

- NVDIMM: 2666MHz

*Max. memory capacity and frequency are to be validated

Volt age 1.2V

Expansion Slot

PCIe 4.0 x 16 PCIE4: Gen4 x16 link

PCIE5: Gen4 x16 link

PCIE6: Gen4 x16 link

Storage

SATA Controller AMD EPYC 7003/7002 series processors

11SATA 6Gb/s: 2 Mini-SAS HD, 2 SATA 7-pin, 1 M.2

M.2 Slot 1 (M2_1: 2280, PCIe4.0 x4 or SATA 6Gb/s)

SlimSAS 2 Low-Prole SlimSAS (PCIe4.0 x8)

Mini-SAS HD 2 (SATA Gen3 x8)

Ethernet

Interface ROMED8U-2T:

10000/1000/100 Mbps by Intel®X710-AT2

ROMED8U-2T/BCM:

10000/1000/100 Mbps by Broadcom 57416B

ROMED8U-2T

ROMED8U-2T/BCM

2 3

English

LAN Controller ROMED8U-2T:

- 2 x RJ45 10GbE RJ45 by Intel® X710-AT2

- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN1 supports NCSI

ROMED8U-2T/BCM:

- 2 x RJ45 10GbE RJ45 by BCM 57416B

- 1 x RJ45 Dedicated IPMI LAN port by RTL8211E

- Supports Wake-On-LAN

- Supports Energy Ecient Ethernet 802.3az

- Supports Dual LAN with Teaming function

- Supports PXE

- LAN1 supports NCSI

Management

BMC Controller ASPEED AST2500

IPMI Dedicated

GLAN

1 x Realtek RTL8211E for dedicated management GLAN

Features Watch Dog

NMI

Graphics

Controller ASPEED AST2500

Rear Panel I/O

VGA Port 1 x D-Sub

USB 3.2 Gen1 Port 2

LAN Port - 2+1 RJ45 Gigabit Ethernet LAN port

- LAN Ports with LED (ACT/LINK LED and SPEED LED)

UID 1

Internal Connector

Auxiliary Panel

Header

1 (includes chassis intrusion, location button & LED, and front

LAN LED)

Panel Header 1

TPM Header 1

TPM-SPI Header 1

IPMB Header 1

Fan Header 3 Fans (6-pin) + 3 Fans (4-pin)

ATX Power 2 x (8-pin) + 1 x (4-pin)

SATA Power 1 (6-pin)

USB 3.2 Gen1

Header

1 (supports 2 USB 3.2 Gen1 ports)

SATA SGPIO 1

4 5

English

CPU_HSBP1 1

BMC SMB 1

PSU SMB 1

ermal Sensor

Header

1

Speaker 1 (4-pin)

COM Header 1

ClearCMOS 1 (short pad)

OH/FanFail LED 6 (only Fan Fail LED)

System BIOS

BIOS Ty pe 32MB AMI UEFI Legal BIOS

BIOS Features - Plug and Play (PnP)

- ACPI 2.0 Compliance Wake Up Events

- SMBIOS 2.8 Support

- ASRock Rack Instant Flash

Hardware Monitor

Temperature - CPU Temperature Sensing

- MB/TR1/Card side Temperature Sensing

Fan - Fan Tachometer

- CPU Quiet Fan (Allow CPU Fan Speed Auto-Adjust by CPU

Temperature)

- Fan Multi-Speed Control

Volt age Voltage Monitoring: Vsoc,Vcpu, VCCM, VPPM, 3V/5V/12V,

+BAT, 3VSB, 5VSB

Support OS

OS Microso® Windows®:

- Server 2016 (64 bit)

- Server 2019 (64 bit)

Linux®:

- RedHat Enterprise Linux Server 8.3 (64 bit) / 8.4 (64 bit)

- CentOs 8.3 ( 64 bit) / 8.4 (64 bit)

- SUSE SLES 15.2 (64 bit) / 12.5 (64 bit)

- UBuntu 20.04.1 (64 bit) /18.04.5 (64 bit)

Hypervisor:

- VMWare® ESXi 6.7.0 u3 / vSphere 6.7.0 u3

- VMWare® ESXi 7.0 U1 / vSphere 7.0 U1

- VMWare® ESXi 7.0U2a / vSphere 7.0U2b

- CITRIX Hypervisor 8.2.0

* Please refer to our website for the latest OS support list.

Environment

Temperature Operation temperature: 10°C ~ 35°C / Non operation

temperature: -40°C ~ 70°C

NOTE: Please refer to our website for the latest specications.

4 5

is motherboard supports Wake from on Board LAN. To use this function, please make

sure that the “Wake on Magic Packet from power o state” is enabled in Device Manager

> Intel® Ethernet Connection > Power Management. And the “PCI Devices Power On” is

enabled in UEFI SETUP UTILITY > Advanced > ACPI Conguration. Aer that, onboard

LAN1&2 can wake up S5 under OS.

If you install Intel® LAN utility or Marvell SATA utility, this motherboard may fail Win-

dows® Hardware Quality Lab (WHQL) certication tests. If you install the drivers only, it

will pass the WHQL tests.

6 7

English

1.3 Unique Features

ASRock Rack Instant Flash is a BIOS ash utility embedded in Flash ROM. is convenient

BIOS update tool allows you to update system BIOS without entering operating systems rst

like MS-DOS or Windows®. With this utility, you can press the <F6> key during the POST or

the <F2> key to enter into the BIOS setup menu to access ASRock Rack Instant Flash. Just

launch this tool and save the new BIOS le to your USB ash drive, oppy disk or hard drive,

then you can update your BIOS only in a few clicks without preparing an additional oppy

diskette or other complicated ash utility. Please be noted that the USB ash drive or hard

drive must use FAT32/16/12 le system.

ROMED8U-2T

ROMED8U-2T/BCM

6 7

English

1.4 Motherboard Layout

24.4cm (9.6 in)

23

9

10

12

1

SPEAKER1

13

14

16

17

18

19

21

222526

1

20

2324

UID1

IPMI_LAN

LAN_1

VGA1

PCIE6

PCIE5

PCIE4

CPU1

ATX12V2

ATX12V1

ATX4PIN1

BAT1 FAN1 FAN2 FAN3

DDR4_H1

DDR4_G1

DDR4_F1

DDR4_E1

FAN4

FAN5

FAN6

SATA_PWR1

DDR4_A1

DDR4_B1

DDR4_C1

DDR4_D1

SLIM2

SLIM1

TPM_BIOS_PH1

M2_1

SATA1

SATA0

SATA_SGPIO3

CPU_HSBP1

TPMS1

AUX_PANEL1

PANEL1

MSAS_HD0

USB3_3_4

COM1

IPMB_1

BMC_SMB1

BMC

ROM

BIOS

ROM

Intel

X710-AT2

LAN_2

45 678

11

15

273132 283033

37

34

38

36

35

39

PSU_SMB1

ROMED8U-2T

1

T 1

R

USB 3.2 Gen1

T: USB_2

B: USB_1

(NCSI)

Super

I/O

CLRMOS1

ASPEED

AST 2500

29

ROMED8U-2T/BCM

(ROMED8U-2T only)

BCM

57416B

(ROMED8U-2T/BCM only)

8 9

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 ATX 12V Power Connector (ATX12V2)

3 ATX 4-PIN Power Connector (ATX4PIN1 (ATX 24pin-to-4pin))

4 Battery (BAT1)

5 PSU SMBus Header (PSU_SMB1)

6 System Fan Connector (FAN1)

7 System Fan Connector (FAN2)

8 System Fan Connector (FAN3)

9 2 x 288-pin DDR4 DIMM Slots (DDR4_F1, DDR4_H1)*

10 2 x 288-pin DDR4 DIMM Slots (DDR4_E1, DDR4_G1)*

11 AMD Socket SP3 (LGA4094)

12 System Fan Connector (FAN4)

13 System Fan Connector (FAN5)

14 System Fan Connector (FAN6)

15 SATA Power Connector (SATA_PWR1)

16 Low-Prole Slimline SAS Connector (SLIM2)

17 Low-Prole Slimline SAS Connector (SLIM1)

18 M.2 Socket (M2_1) (Type 2280)

19 MiniSAS HD Connector (MSAS_HD0)

20 TPM Header (TPMS1)

21 System Panel Header (PANEL1)

22 Auxiliary Panel Header (AUX_PANEL1)

23 ermal Sensor Header (TR1)

24 Speaker Header (SPEAKER1)

25 Backplane PCI Express Hot-Plug Connector (CPU1_HSBP1)

26 SATA SGPIO Connector (SATA_SGPIO3)

27 Clear CMOS Pad (CLRMOS1)

28 SATA3 Connector (SATA0)

29 SATA3 Connector (SATA1)

30 USB 3.2 Gen1 Header (USB3_3_4)

31 COM Header (COM1)

32 Intelligent Platform Management Bus Header (IPMB_1)

33 BMC SMBus Header (BMC_SMB1)

ROMED8U-2T

ROMED8U-2T/BCM

8 9

English

No. Description

34 PCI Express 4.0 x16 Card Slot (PCIE4)

35 PCI Express 4.0 x16 Card Slot (PCIE5)

36 PCI Express 4.0 x16 Card Slot (PCIE6)

37 2 x 288-pin DDR4 DIMM Slots (DDR4_B1, DDR4_D1)*

38 TPM-SPI Header (TPM_BIOS_PH1)

39 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_C1)*

*For DIMM installation and conguration instructions, please see p.21 (Installation of Memory Modules

(DIMM)) for more details.

10 11

English

1.5 Onboard LED Indicators

23

1

4

5

6

7

8

ROMED8U-2T

ROMED8U-2T/BCM

10 11

English

No. Item Status Description

1 SB_PWR1 Green STB PWR ready

2FAN_LED1 Amber FAN1 failed

3FAN_LED2 Amber FAN2 failed

4FAN_LED3 Amber FAN3 failed

5FAN_LED4 Amber FAN4 failed

6FAN_LED5 Amber FAN5 failed

7FAN_LED6 Amber FAN6 failed

8BMC_LED1 Green BMC heartbeat LED

12 13

English

1.6 I/O Panel

12

3

4

5

6

No. Description No. Description

1 UID Switch (UID1) 4 10G LAN RJ-45 Port (LAN1)**

2 USB 3.2 Gen1 Ports (USB3_1_2) 5 10G LAN RJ-45 Port (LAN2)**

3 LAN RJ-45 Port (IPMI_LAN1)* 6 VGA Port (VGA1)

*ere are two LED next to the LAN port. Please refer to the table below for the LAN port

LED indications.

Dedicated IPMI LAN Port LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10M bps connection or no

link

Blinking Yellow Data Activity Yel low 100M bps connection

On Link Green 1G bps connection

ACT/LINK LED

SPEED LED

LAN Port

ROMED8U-2T

ROMED8U-2T/BCM

12 13

English

**ere are two LEDs on each LAN port. Please refer to the table below for the LAN port

LED indications.

LAN Port (LAN1, LAN2) LED Indications

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 100Mbps connection or

no link

Blinking Yellow Data Activity Yel low 1Gbps connection

On Link Green 10Gbps connection

ACT/LINK LED SPEED LED

LAN Port

ACT/LINK LED SPEED LED

14 15

English

1.7 Block Diagram

5

4

3

2

1

D D

C C

B B

A A

R/LRDIM M

8 DIMM Slots

1 x DDR4 LRDIMM/RDIMM

AMD Family 17h Processor

DDR4 DDR4DDR4

CPU

AMD EPYC 700x

PCI-E

Port G0

Port G2.6

Port G3.0~7

REALTEK

RTL8211E

10/100/1G PHY

DDR4 DDR4DDR4

1 x DDR4 LRDIMM/RDIMM

Port P1

DDR4 DRAM

(512MB)

BMC

AST2500

Ethernet

10/100/1000

Video

DAC

BMC &

VR AM

PCI-Express

USB

1.1 &

2.0

LPC

MAC2

SPI

SPI FLASH

(512Mb)

PCI-E Gen3

x1

LPC

PCIE Gen3 x 1

LPC

USB

USB2.0 x 2

TPM 2.0

PCI-E

G1 Port4

Port G2.0~3

x16

1 x DDR4 LRDIMM/RDIMM

NCSI

USB 3.2 USB3.2 x 4

F_USB1

SIO

NCT6779

Ethernet

10/100/1000

MAC1

SLIM2

Port G3.8~15

PCIe Gen4 x8

Slimline Conn.

PCIE Gen4 x 16

S AT A G e n 3 x 2

PCIE Gen4 x 16

PCIE5

SATA 7Pin

PCIe Gen4 x8

MSAS_HD0

Mini SAS HD

S AT A G E N 3 x 8

Port P2

PCI-E

x16

Port G1 0~3

PCIE Gen3 x 4

INTEL

X710-AT2

10G

R/LRDIM M

SATA SGPIO Configuration

SATA0 , SATA1 use SGPI O_2

MSAS_HD0 use SGPIO_3

Port G2.4~5

Port G2.8~15

S AT A G E N 4 x 4

SLIM1

Slimline Conn.

M2_1

M.2 Socket

Support:

1. SATA

2. PCIE

Port P0

PCI-E

x16

PCIe Gen4 x16

PCIE4

PCIE6

PCI-E

x4

R/LRDIM M R/LRDIM M

DDR4

1 x DDR4 LRDIMM/RDIMM1 x DDR4 LRDIMM/RDIMM

Share SATA

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

1129Wednesday, July 21, 2021

Asrockrack

000-BLOCK

R1.00

ROMED6U-2L2T

Eric H u

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

1129Wednesday, July 21, 2021

Asrockrack

000-BLOCK

R1.00

ROMED6U-2L2T

Eric H u

Size

Project Name

Rev

Date: Sheet of

Title :

Engineer:

C

1129Wednesday, July 21, 2021

Asrockrack

000-BLOCK

R1.00

ROMED6U-2L2T

Eric H u

ROMED8U-2T:

Page is loading ...

ASRock Rack ROMED8U-2T User manual

ASRock Rack ROMED8U-2T User manual

Related papers

Other documents