Haier HL52E User manual

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

MODELS:

HL37E

HL42E

HL47E

HL52E

2 TV LCD-TFT

THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT

INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT

WITH ANY INSIDE PART OF THIS PRODUCT.

WARNING : To reduce the risk of electric shock do not remove cover or back.

No user-serviceable parts inside refer service to qualified service personnel.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, use and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However ,there is no

guarantee that interference with not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encourage to try to correct the interference by one or

more of the following measures:

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

*Consult the dealer or an experienced radio/TV technician for help.

This device compiles with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may be not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC CAUTION:

To assure continued compliance and possible undesirable interference, the provided ferrite

cores must be used when connecting this plasma display to video equipment; and maintain

at least 40cm spacing to other peripheral device.

CANADIAN NOTICE:

This Class B digital apparatus compiles with Canadian ICES-003.

RISK ELECTRIC SHOCK

DO NOT OPEN

WARNING

Safety of operators has been taken into consideration at the design and manufacture

phase, but inappropriate operation may cause electric shock or fire. To prevent the product

from being damaged, the following rules should be observed for the installation, use and

maintenance of th product. Read the following safety instruction before starting the operation.

The User Manual uses the following symbols to ensure a safe operation and prevent

any damage to operators or properties:

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE APPLIANCE.

FCC STATEMENT

Owner s Manual 3

IMPORTANT SAFETY INSTRUCTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the following:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of

time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,

shall be placed on the apparatus.

S3126A

PORTABLE CART WARNING

(symbol provided by RETAC)

The apparatus shall not be exposed to dripping or splashing and that no objects filled

with liquids, such as vases, shall be placed on the apparatus.

The mains plug is used as the disconnect device, remain it readily operable during the

apparatus normal use.

SAVE THESE INSTRUCTIONS

Thank you for using our Haier product. This easy-to-use manual will guide you in

getting the best use of your product. Remember to record the model and serial

number. They are on label in back of the unit.

Model number

serial number

Date of purchase

Staple your receipt to your manual. You will need it to obtain warranty service.

4 TV LCD-TFT

Contents

Introduction

Owner s Manual 5

War nin g . . . . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .

Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Introduction

Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ... ..

Connection Options . . . . . . . . . . . . . . . . . . . . . .............

Universal Remote Controller . ............ . . . . . . . . ......

Installation

Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... ... ... ..

Antenna Connection . . . . . . . . . . ..............................

VCR Connection. . . . . . . . . . . . . . . . . . . . . ............... ..

External A/V Source Setup . . . . .. . . . . ......................

DVD Connection . . . . . ...... . . . . . . . . . . . . . ................

DTV Connection.....................................................

Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............

PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .

HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... ... ... ... ... .

Cable Sample.........................................................

Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .

Pow er so urc e.. ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .

Operation

Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...

Choose the Menu Language . . . . ..... .......................

Choose the input Source.........................................

Channel Menu

Automatic Scan. . . . . . . . . . . . . ............................. . .

Man ual S can . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . .. .

Fine Tune................................................................

Edi t Pro gra m.. ... ... ... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..

Rename .............. . . . . . . . . . . . . . . . . . . . . . . . . ..........

S . . . . . ........... ............ . . ..

S . . .............. . . . ............ . . ..

Mute .............. . . . ............................................ . . ..

Video Menu

Asp ect R ati o Con tro l . . . . . . . . . . . . . . . . . . . . ... . .. . . ..

Audio Menu

SAP Broadcasts Setup............................................

elect the desired program

elect the desired sound

How to select picture modes.....................................

How to customize your own picture status .................

How to select audio modes......................................

How to customize your own audio status ..................

Time Menu

Function Menu

Closed Captions.....................................................

CC mode...............................................................

........................................................

DTV Caption..........................................................

DTV Caption Style..................................................

.........................................................

...........................................................

..................................................

Menu

Screen Setup for PC mode......................................

Lock Menu

Parental Control rating and categories......................

Others Functions

Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... .. . .

Maintenance . . ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Specifications . . . . . . . . . . . . . . . . . . . . . . .. .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .

Warranty . . . . ... ... ... ... . . . . . . . . . . . . . . . . . . . .. . . . . . .

Date /Time setting...................................................

Timer on setting......................................................

Timer off setting......................................................

Sleep Timer setting.................................................

Time zone setting...................................................

Daylight Saving setting...........................................

NTSC Caption

OSD Timeout

Blue screen

OSD transparency

Adjust

Quick program view................................................

Setting up your remote control ................................

USB system .......................................................

-This is a simplified representation of front panel.

-Here shown may be somewhat different from your TV.

Controls

Introduction

6 TV LCD-TFT

Front panel controls

1.CH-/+ Program minus and plus, menu options

2.VOL-/+ Volume increase and decrease, menu reset and entry

4..MENU Menu display

5.POWER:Is used to activate the display or return to standby mode

3.INPUT: all input resouce display and OK confirm:

CH

INPUT

MENU

-

CH+

VOL - VOL+

POWER

P

C

A

C IN

H

D

M

I2

A

N

T

I

N

P

r

P

b

Y

L

R

H

D

M

I1

P

C

/D

V

I

A

U

D

IO

I

N

O

P

T

I

C

A

L

S

-

V

ID

E

O

V

I

D

E

O

1

L

R

2

1

C

O

M

P

O

N

E

N

T

S-Video Input

Connect S-Video out from

an S-VIDEO device to the

S-VIDEO input.

HDMI1

connect a signal to

HDMI/DVI.

Antenna Input

Connect cable or antenna

signals to the TV, either

directly or through your

cable box.

PC VIDEO Input

Connect the monitor

output connector from

a PC to the jack

DVI/PC Audio Input

Connect the audio out from

the external device, used

while using a DVI to HDMI

connector.

DVD/DTV Input

(Component )

Connect a component

video device to these

jacks.

Earphone jack:

Earphone audio

output terminal.

VIDEO Input

Connects the

video signal

from a video

device.

HDMI2

connect a signal to

HDMI/DVI.

Power Cord Socket

This TV operates on AC

power.

The voltage is indicated on

the Specifications page.

Never attempt to operate

the TV on DC power

Power Cord Socket

This TV operates on AC

power.

The voltage is indicated on

the Specifications page.

Never attempt to operate

the TV on DC power

Connection Options

Left side connetions

CC HH LL II SS TT FF

AAVV.. LL SS

TT

II

AA UU DDII OO

II SS TTLL

EEEDDDOOOMMMVVVTTT EEEDDD

OOO

MMM

TVTVTV

ZOOM

ZOOMZOOM

RETURN

TI

M

E

TI

M

E

POWER

Turns your TV or any other programmed

equipment on or off, depending on mode.

- The remote controller cannot be operated unless the batteries are properly loaded.

Function introduction

- When using the remote control, aim it at the remote control sensor on the TV.

SAP

Selects MTS sound: Mono, Stereo, and SAP in Analog

mode. Change the audio language in DTV mode.

Introduction

FAVORITE

Open the favorite channel list.

THUMBSTICK

(Up/Down/Left/Right/OK)

Allows you to navigate the on-screen menus and adjust

the system settings to your preference.

CHANNEL UP/DOWN

Selects available channels

P.MODE

Selects the picture appropriate

for the program`s character.

FREEZE

Freezes the currently-viewed picture, but audio continues.

Press FREEZE button again to resume the normal picture.

ARC

(Aspect Ratio Control)

Changes the aspect ratio.

S.MODE

Selects the sound appropriate for the program's

character.

VOLUME UP/DOWN

Increases/decreases the sound level.

Numeric buttons

press to change the channel.

EXIT

Clears all on-screen displays and

returns toTV viewing from any menu.

INPUT

show the input source mode.

MUTE

Switches the sound on or off

CC(closed caption)

Select a closed caption:

CC MUTE, CC ON, CC OFF.

TIME

Shows time.

INFO

When you watch the TV, press the key, the information

displays on bottom of the screen.

MENU

Brings up the main menu to the screen.

TV

Press to enter TV signal

SLEEP button

Displays the Sleep Timer option.

Q.VIEW

Switch the current channel to the last channel

you have viewed.

CH.LIST

Open the channel list.

Remote Controller

TV USB

Press the SELECT button repeatedly to select one of the

system modes in which the remote control can be used.

When the desired device is selected, the corresponding

LED lights on 5seconds.

.

/ Rewind / Fast

/ backward /Forward

Play

II Pause

AUDIO.LIST

Open the audio channellist.

- button

Press to select additional channels

(digital and analog)

being broadcast by the same station.

For example, to select channel

“54-3”, press “54”, then press “-” and “3”.

LIGHT

Press the light button, white LED will be ON, release

this key, white LED will be OFF.

8 TV LCD-TFT

USB

Press to enter USB signal

ZOOM( only SUB System)

To enlarge or lessen the picture

Note: For DVD function see page 35.

HOTKEY

CC HH LL II SS TT FF

AA VV..LL SS

TT

II

AA UU DDII OO

II SS TTLL

EEEDDDOOOMMMVVVTTT EEEDDD

OOO

MMM

TVTVTV

ZOOM

ZOOMZOOM

RETURN

TI

M

E

TI

M

E

HOTKEY

RETURN

HOTKEY

( only SUB System)

Call up the menu

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an

outdoor antenna .In different places, the suitable antenna type and position are different.

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall Antenna

Socket

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

VHF Antenna

UHF Antenna

Turn clockwise to tighten.

RF Coaxial Wire (75 ohm)

Bronze Wire

Be careful not to bend the bronze wire when

connecting the antenna.

Bronze Wire

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install a 2-

Way Signal Splitter in the connections.

If the antenna is not installed properly, contact your dealer

for assistance.

Installation

Accessories

Remote controller

Owner`s manual

Alkaline battery(AAA) 2

Power cable

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

Owner s Manual 9

CCHH LLI I SSTT FF

AAVV..LL SS

TT

II

AAUUDDIIOO

IISSTTLL

EEEDDDOOOMMMVVVTTT EEEDDD

OOO

MMM

TVTVTV ZOOM

ZOOMZOOM

RETURN

T

I

M

E

T

I

M

E

HOTKEY

Pr2Pb2

Y2

ANT IN

Pr1Pb1

Y1

L R

S-VIDEO

VIDEO L R

AV OUT L R

VCR connection

NOTE: All cables shown are not included with the TV.

There are several ways to connect your television, depending on the components you want to connect

and the quality of the signal you want to achieve. The following are examples of some ways to connect

your TV. Choose the connection which is best for you.

External Equipment Connections

Choose Your Connection

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

Connection Option 1

Set VCR output switch to channel 3 or 4 and

then tune the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as

shown in the figure.

When connecting the TV to VCR, match the

jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

If you connect an S-VIDEO output from VCR to

the S-VIDEO input, the picture quality is

improved; compared to connecting a regular

VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner`s

manual.)

3. Select the input source with using the

INPUT button on the remote control, and

then press / button to select the source,

press the OK button to confirm.

Installation

10 TV LCD-TFT

R

S-VIDEO

VIDEO L R

AV OUT L R

Pr2Pb2

Y2

Pr1Pb1

Y1

L

R

S-VIDEO

VIDEO L R

AV OUT L R

Pr2Pb2

Y2

Pr1Pb1

Y1

L

How to connect

1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb,

Pr jacks on the TV and connect the DVD audio outputs to the

YPbPr Audio IN jacks on the TV, as shown in the figure.

2. If your DVD only has an S-VIDEO output jack, connect this

to the S-VIDEO input on the TV. as shown in the figure.

NOTE: If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT button on the remote control to select YPbPr

mode.

3. Press Play button on external equipment for program play.

4. Refer to the DVD player's manual for operating instructions.

DVD connection

External Equipment Connections

How to connect

Connect the audio and video cables from the external equipment's

output jacks to the TV input jacks, as shown in the figure.

When connecting the TV to external equipment, match the

jack colors (Video = yellow, Audio Left = white, and Audio

Right = red).

How to use

1. Select the input source with using the INPUT button on

the remote control.

2. Press the / button to select the desired source.

3. Press the ok button to confirm

4. Operate the corresponding external equipment.

External A/V Source Setup

Video Game Set

Camcorder

Component Input ports

To get better picture quality, connect a DVD player to the component

input ports as shown below.

Installation

Component ports

on the TV

Video output ports

on DVD player

Y Pb Pr

Y B-Y R-Y

Y Cb Cr

Y P P

BR

Owner s Manual 11

Pr2Pb2

Pr1Pb1

L R

HDMI1

PC/DVI

AUDIO IN

OPTICAL

S-VIDEO

VIDEO L R

AV OUT L R

PC

Y2

Y1

Digital Set-top Box

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital

signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV`s (Y, PB, PR) , PC or HDMI

jack for video connections, depending on

your set-top box connector. Then, make

the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer

to the owner`s manual for the digital

set-top box.)

2. Use INPUT on the remote control to select

YPbPr, PC,or HDMI source.

Send the TV`s audio to external audio equipment (stereo system) via

the Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Audio (Optical)

Output port.

2. Connect the other end of the optical cable to the digital audio (optical)

input on the audio equipment.

See the external audio equipment instruction manual for operation.

Note: When connecting with external audio equipments, such as

amplifers or speakers, please turn the TV speakers off.

Audio Output

Caution: Do not look into the optical output port.

Looking at the laser beam may damage

your vision.

External Equipment Connections

DTV connection

AC IN

PC/DVI

AUDIO IN

OPTICAL

Installation

Signal

480i

480p

720p

1080i

YPbPr

Yes

HDMI/DVI

Yes

12 TV LCD-TFT

PC

HDMI2

ANT IN

HDMI1

PC/DVI

AUDIO IN

OPTICAL

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024

2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherPC r DVI IN to

display the PC on the TV.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe DVI; (the other mode is

set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Use INPUT on the remote control to select PC or HDMI source.

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC

mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness

and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic

card or consult the manufacturer of the PC graphic card.

NOTES:

1 Use a DVI cable.

2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the

screen.

3 The synchronization input form for Horizontal and Vertical frequencies is separate.

x768 .

IN o

r PC or

PC connection

Resolution

Frame

frequency

(Hz)

PC

SPC

XGA

640*480 60Hz

800*600 60Hz/75Hz

1024*768

60Hz

Mode

Resolution

External Equipment Connections

Installation

75Hz

Owner s Manual 13

Pr2Pb2

Y2

Pr1Pb1

Y1

L R

S-VIDEO

VIDEO L R

AV OUT L R

External Equipment Connections

The TV has a special signal output capability which allows you to

hook up a second TV or monitor.

Connect the second TV or monitor to the TV`s AV OUT.

See the Operating Manual of the second TV or monitor for further

details regarding that device`s input settings.

Notes:

YPbPr, PC, HDMI,DTV input sources

cannot be used for Monitor out.

When connecting with external audio equipments, such as amplifers

or speakers, please turn the TV speakers off.

Monitor Out Setup

Installation

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI input source in input source option of Select Main source menu.

How To Connect

1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

2. A separated audio connection is necessary.

3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the

left side of HDMI port.

How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Press the INPUT button to select HDMI input source in input source option of Select Main source menu.

HDMI

14 TV LCD-TFT

Cable sample

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Analog Audio Cable

(Stereo to RCA type)

(not supplied with the product)

Installation

Owner s Manual 15

HDMI1

PC/DVI

AUDIO IN

OPTICAL

Power source

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for

operation on AC. Insert the AC cord plug into

a standard polarized AC outlet.

NOTES:

Never connect the AC line cord plug to other

than the specified voltage. Use the

attached power cord only.

If the polarized AC cord does not fit into a non-

polarized AC outlet, do not attempt to file or cut

the blade. It is the user`s responsibility to have

an electrician replace the obsolete outlet.

If you cause a static discharge when touching

the unit and the unit fails to function, simply

unplug the unit from the AC outlet and plug it

back in. The unit should return to normal operation.

You can connect a set of headphones to your set if you wish to watch a

TV programme without disturbing the other people in the room.

Connecting Headphones

External Equipment Connections

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Plug a set of headphones into the 3.5mm

mini-jack socket on the rear panel of the set.

Installation

16 TV LCD-TFT

AC Outlet

Polarized AC Cord Plug

(One blade is wider than the other.)

Wider Hole

and Blade

Switching On/Off the TV set

Choose the Menu Language

When you start using your set for the first time, you must select the language which will be used for displaying menus

and indications.

-In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an

example to help you with the TV operation.

Operation

-There are several options you might need to set up in order for your TV to work properly. Read the

instructions that follow.

Note:

If the TV in power on , the screen show information according the type of input signal . the information

will disappear. If there is no signal and blue screen in ON the screen enter in bluescreen and display No signal

on top and center of the screen.

1 Press the MENU button and then use / button to select the

Function menu.

2 Press the button and then use / button to select Menu

Language.

3 Press the button and then use / button to enter the list of

available language. English Spanish or French

4 Select your language with the / button and press the OK

button to confirm you selection.

5 When you are satisfied with your choice, press the EXIT button

to return to normal viewing or press MENU button to return to the

previous menu.

1. First, connect power cord correctly, and then press POWER button on the remote control to turn on the TV.

2. Select the viewing source by using INPUT button on the remote control.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

4. If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

English

Spanish

French

Menu Language English

CC Mode On

Basic Caption CC1

Advanced Caption Service1

Caption Type Basic

Caption Style

OSD Timeout Middle

Blue Screen On

OSD transparency Middle

B

C

A

Video

Audio

Time

Channel

Function

Lock

Choose the Input source

- Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are

connected to your TV.

1. Press the INPUT button to enter the Select Main picture Source menu

and then use / button to select the desired items. Cable/Air TV, ,

, SVIDEO, 1, 2, PC, HDMI1, HDMI2,INNER

DVD.

2. Press the OK button to confirm.

3. Press INPUT button to return to TV viewing or press EXIT button to return to the

previous menu.

VIDEO1

VIDEO2 COMPONENT COMPONENT

Select Main Source

AIR TV

VIDEO1

VIDEO2

SVIDEO

COMPONENT1

COMPONENT2

PC

HDMI1

HDMI2

INNER DVD

DVD

STB

PVR

Cable

Game

Up/Down:Move Cursor

OK: Change MP Source

Right:Activale Source Name Edit Menu

Operation

Note:

1. According to your connection device, you can change the name of every source.

2. In channel menu, if the Tuner item is set ting as Air or Cable, the source menu will display Air TV or Cable TV;

Owner s Manual 17

This TV set has three methods to set channels, which are respectively Auto Scan, manual Scan fine tune.

In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV

set to set channel.

A password is required to gain access to Channel menu if the Lock of Edit program menu is turned on.

Automatic Scan

Note : Channel menu only available after selecting Air TV or Cable

TV in the input menu.

Channel menu

- Automatically finds all channels available through antenna or cable inputs, and

stores them in memory on the All Channel List.

When Air is selected, the TV will detect antenna signals and will

search for antenna TV (NTSC and ATSC) channels available in

your local area.

When Cable is selected, the TV will detect cable company supplied

signals and will search for cable TV (NTSC,ATSC, QAM modulated)

channels available in your area.

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Tuner.

3 Press the button and then use / button to Select Cable or

Air mode.

4 Press the OK button

5 When you are satisfied with your choice, press MENU button to

return to the previous menu.

6 Press the / button to select Auto Scan.

7 Press the button and press the OK button to start searching.

8 To cancel searching, press the OK button.

: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Air

Cable

B

C

A

Video

Audio

Time

Channel

Function

Lock

OK Cancel

Air Tuner Number: 47

Found: 1

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Operation

: Move cursor, OK: Enter, MENU: Return to upper menu,

EXIT: Exit main menu

18 TV LCD-TFT

Manual Scan

Channel menu

If excessive channel signals of unwanted programs are received in local area,

manual search function is recommended.

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Tuner.

3 Press the button and then use / button to Select Cable or Air

mode.

4 Press the OK button.

5 When you are satisfied with your choice, press MENU button to return

to the previous menu.

6 Press the / button to select Manual Scan.

7 Press the button and then use digital buttons to select channel number you want to add or delete.

8 Press the button to select OK item and press OK button to add for the channel number.

9 Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Fine Tune (only in anolog signal )

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the / button to select Fine Tune.

3 Press the or OK button

4 Press the button to tune.

5 Press EXIT button to return to TV viewing or press MENU button

to return to the previous menu.

/

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Type

Air

Channel NO

Frequency

0k

4

67.250MHz

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

For the tune of the analog channels

Operation

: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,

EXIT: Exit main menu

: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,

EXIT: Exit main menu

Owner s Manual 19

Channel menu

Edit Program

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Edit Program.

3 Press the button. You will now see a screen filled with channel numbers.

4 Use / / / button to select FAV., Lock or Skip item, and then use the OK button to confirm.

5 When you are satisfied with your choice, press MENU button to return to the previous menu or Press EXIT button

to return to TV viewing.

Skip

After the programs are presetting, you can skip some programs so that to select your favorite channels only.

You can create your own Favorite List. Use the

on on the remote control when a channel is highlighted and

then you can add or delete the channel to/from the Favorite List.

You can skip some channel;

You can lock some channel;

FAV.LiST butt

Rename (only in anolog signal )

1 Press the MENU button and then use / button to select the

Channel menu.

2 Press the button and then use / button to select Rename.

3 Press the or OK button to enter the Submenu.

4 The cursor flashs, Use the digital button to select the letter, and

press / button to move the cursor and button to confirm.

(Press the Q.VEIW button to delete the letter. )

5 When you are satisfied with your choice, press MENU button to

return to the previous menu or Press EXIT button to return to TV

viewing.

MENU

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Lock

After the programs are presetting, you can lock some programs so that to select your favorite channels only.

Fav (Favorite)

Press the FAV.LiST button open the favorite channel list, press / button to select the

channel and press OK button to confirm.

Ch No Name SkipLock

Fav

Music

B

C

A

Video

Audio

Time

Channel

Function

Lock

Tuner Air

Auto Scan

Manual Scan

Fine Tune

Edit Program

Rename

Program No

Program Name

Operation

Page 1/1

: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,

EXIT: Exit main menu

: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,

EXIT: Exit main menu

20 TV LCD-TFT

Page is loading ...

Haier HL52E User manual

Haier HL52E User manual

Related papers

Other documents