evertz 1275T User manual

1275T/1285T Series

Digital Clock Display

User Manual

EVERTZ MICROSYSTEMS LTD.

5292 John Lucas Drive

Burlington, Ontario

Canada L7L 5Z9

Phone: +1 905-335-3700

Sales: [email protected] Fax: +1 905-335-3573

Tech Support: service@evertz.com Fax: +1 905-335-7571

Web Page: http://www.evertz.com

Version 1.0, May 2015

The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of

purchasers of the 1275T/1285T series product. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the

operation of the 1275T/1285T series product. Due to on going research and development, features and specifications in this manual are subject

to change without notice.

this manual can be ordered from your Evertz dealer or from Evertz Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS

The lightning flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of uninsulated “Dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance (Servicing) instructions

in the literature accompanying the product.

• Read these instructions

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than other. A grounding-type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC – SHOCK, DO NOT EXPOSE THIS

APPARATUS

TO RAIN OR MOISTURE

WARNING

DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO

OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT

WARNING

TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE

POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE

WARNING

THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE

INFORMATION TO USERS IN EUROPE

NOTE

CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to the European Union EMC directive. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

INFORMATION TO USERS IN THE U.S.A.

NOTE

FCC CLASS A DIGITAL DEVICE OR PERIPHERAL

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

WARNING

Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s

authority to operate the equipment.

Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables

with the shield connected to the chassis ground of the device must be used.

EN60065

Safety

EN504192 2005

Waste electrical products should not be

disposed of with household waste.

Contact your Local Authority for recycling

advice

EN55103-1: 1996

Emission

EN55103-2: 1996

Immunity

1275T / 1285T Series

Digital Clock Display

TABLE OF CONTENTS Revision 1.0 Page - i

TABLE OF CONTENTS

1. OVERVIEW ................................................................................................................................... 1

2. INSTALLATION ............................................................................................................................. 3

2.1. MOUNTING ........................................................................................................................... 3

2.2. CONNECTORS ..................................................................................................................... 4

2.2.1. Time Code Connectors .............................................................................................. 4

2.2.2. Ethernet Connections ................................................................................................ 4

2.2.3. Serial Port Connections ............................................................................................. 5

2.3. POWER ................................................................................................................................ 6

2.4. POWER OVER ETHERNET (POE) ....................................................................................... 6

3. SPECIFICATIONS ......................................................................................................................... 7

3.1. FUNCTIONAL ....................................................................................................................... 7

3.2. SERIAL PORT ...................................................................................................................... 7

3.3. TIME KEEPING .................................................................................................................... 7

3.4. ETHERNET ........................................................................................................................... 7

3.5. ELECTRICAL ....................................................................................................................... 7

3.6. PHYSICAL ............................................................................................................................ 8

4. OPERATION ................................................................................................................................. 9

4.1. AN OVERVIEW OF THE SETUP MENU SYSTEM ............................................................... 9

4.1.1. Setting the Brightness ................................................................................................ 9

4.1.2. The Setup Menu System ........................................................................................... 9

4.2. FRONT PANEL CONTROLS .............................................................................................. 10

4.2.1. Pushbuttons ............................................................................................................. 10

4.2.2. Front Panel Displays ................................................................................................ 11

4.3. SETUP MENU – TOP LEVEL ............................................................................................. 11

4.3.1. Setting the Input Source .......................................................................................... 12

4.3.2. Setting the Time Zone Offset ................................................................................... 12

4.3.3. Setting the Time Daylight Saving Time Rules .......................................................... 13

4.3.4. Selecting the Time Display Format .......................................................................... 17

4.3.5. Selecting the Date Display Format ........................................................................... 17

4.3.6. Setting the Time....................................................................................................... 18

4.3.7. Setting the Date ....................................................................................................... 18

4.3.8. Setting the Internet Protocol and NTP Rules ............................................................ 19

5. VISTALINK® PRO INTERFACE ................................................................................................... 23

5.1. OVERVIEW ......................................................................................................................... 23

5.2. GENERAL........................................................................................................................... 24

5.2.1. Status ...................................................................................................................... 24

5.2.2. Input ........................................................................................................................ 25

1275T / 1285T Series

Digital Clock Display

Page - ii Revision 1.0 TABLE OF CONTENTS

5.2.3. Display .................................................................................................................... 25

5.2.4. Daylight Saving Time .............................................................................................. 26

5.2.5. Control Port ............................................................................................................. 27

5.3. IP SETTINGS ..................................................................................................................... 28

5.4. FAULT TRAPS ................................................................................................................... 30

6. UPGRADE .................................................................................................................................. 31

6.1. UPGRADE OVERVIEW ..................................................................................................... 31

6.2. VISTALINK® PRO UPGRADE PROCEDURE .................................................................... 32

6.3. UPGRADE FIRMWARE ..................................................................................................... 34

6.3.1. Upgrade through Serial Port .................................................................................... 34

Figures

Figure 1-1 : 1275T/1285T Digital Clock ........................................................................................................... 2

Figure 2-1: 1275T/1285T Rear Panel .............................................................................................................. 3

Figure 3-1: 1275T/1285T Rear Panel .............................................................................................................. 7

Figure 4-1: Setup Menu System ...................................................................................................................... 9

Figure 4-2: 1275T/1285 Front Panel Controls ............................................................................................... 10

Figure 5-1: 1275T/1285T Configuration Tabs ................................................................................................ 23

Figure 5-2: General Settings Configuration ................................................................................................... 24

Figure 5-3: IP Settings Configuration ............................................................................................................. 28

Figure 5-4: Fault Traps Status Viewing .......................................................................................................... 30

Figure 6-1: How to Apply Update ................................................................................................................... 32

Figure 6-2: Upgrade Window ......................................................................................................................... 32

Figure 6-3: Module Dropdown Menu ............................................................................................................. 33

Figure 6-4: Version Information Window ........................................................................................................ 33

Figure 6-5 : 1275T/1285T Serial Port Connection ......................................................................................... 34

Figure 6-6: Serial Connection Parameters ..................................................................................................... 35

Figure 6-7: Serial Terminal – Boot up Screen ................................................................................................ 35

Figure 6-8: Rebooting into Upgrade Mode ..................................................................................................... 36

Figure 6-9: Send File ...................................................................................................................................... 36

Figure 6-10: Select Binary File ....................................................................................................................... 37

Figure 6-11: File Transfer in Progress ........................................................................................................... 37

Figure 6-12: Reboot Screen ........................................................................................................................... 38

Tables

Table 2-1: Standard RJ45 Wiring Colour Codes .............................................................................................. 4

Table 2-2: COM Port Pinout ............................................................................................................................. 5

Table 4-1: DST Start Transition ..................................................................................................................... 13

Table 4-2: DST End Transition ....................................................................................................................... 14

1275T / 1285T Series

Digital Clock Display

REVISION HISTORY Revision 1.0 Page - iii

REVISION HISTORY

REVISION

DESCRIPTION

DATE

1.0

First Release

May 2015

Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor

for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning

performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The

only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order

confirmation form.

Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no

warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or

order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If

you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make

changes in equipment design or specifications.

1275T / 1285T Series

Digital Clock Display

Page - iv Revision 1.0 REVISION HISTORY

This page left intentionally blank

1275T / 1285T Series

Digital Clock Display

OVERVIEW Revision 1.0 Page - 1

1. OVERVIEW

The 1275T/1285T is a multifunction time-of-day display that can act as a slave to a master clock

system or as a self-contained, pre-settable clock.

Sixty bright rectangular LEDs are mounted in a circular arrangement simulating an analog second

hand. Twelve individual round LEDs indicate the hour. In addition, the hours, minutes and seconds are

displayed in digital format.

As a slave display, the unit will read SMPTE/EBU/DQS-B6/NTP time code. The user can program time

zone offsets from the incoming code. As a standalone clock, it can be programmed to operate in either

12 or 24 hour mode. Three unobtrusive front panel push-buttons allow presetting and accurate

synchronization to a standard time source.

The product comes in two sizes - 9” and 12” clock display. Beautifully finished with black wood trim, the

1275T/1285T are ideally suited for studio, lobby, board room or office mounting.

Features and Benefits:

• LED brightness is adjustable

• Runs on 50/60Hz, 115/230V AC power line

• User-programmable time offsets

• VistaLINK® control for device configuration and status monitoring with support of the CP-2232E

or CP-2116E-H Advanced Systems Control Panel

• Programmable daylight saving time start & end times NTP client

1275T / 1285T Series

Digital Clock Display

Page - 2 Revision 1.0 OVERVIEW

Figure 1-1 : 1275T/1285T Digital Clock

1275T / 1285T Series

Digital Clock Display

INSTALLATION Revision 1.0 Page - 3

2. INSTALLATION

The following section describes the methods to mount and connect the device.

2.1. MOUNTING

The 1275T/1285T is equipped with pre-fixed holes in the rear as depicted below in Figure 2-1. The

clock can be mounted through screws on walls at the areas indicated by the arrows in the diagram.

Figure 2-1: 1275T/1285T Rear Panel

1275T / 1285T Series

Digital Clock Display

Page - 4 Revision 1.0 INSTALLATION

2.2. CONNECTORS

The device comes with the ability to connect with other sources, in order to take time information, or

configure & control the wall clock itself. This section provides describes the connection options to the

device. The key sections are the following:

Time Code connections

Allows input and output connect connectivity to time codes.

Ethernet Connection

Allows operation and configuration of the device through a NMS (VL-PRO).

Serial Port connection

Allows configuration of the device through the RS-232 or Serial Port.

2.2.1. Time Code Connectors

There are two LTC IN and LTC OUT connections available in the rear of the device.

IN+, IN-

These two input pins are for connecting SMPTE/EBU longitudinal timecode

(LTC) to the clock.

OUT+, OUT-

These two input pins are for connecting SMPTE/EBU longitudinal timecode

(LTC) to the clock. They are a loop thru from the IN+ and IN- pins.

2.2.2. Ethernet Connections

The 1275T/1285T is designed to be used with either 10Base-T (10 Mbps) or 100Base-TX (100 Mbps)

also known as Fast Ethernet, twisted pair Ethernet cabling systems. When connecting for 10Base-T

systems, category 3, 4, or 5 UTP cable as well as EIA/TIA – 568 100  STP cab

connecting for 100Base-TX systems, category 5 UTP cable is required. The cable must be “straight

through” with a RJ-45 connector.

The straight-through RJ-45 cable can be purchased or can be constructed using the pinout information

in Figure 2-2. A colour code wiring table is provided in Figure 2-2 for the current RJ 45 standards

(AT&T 258A or EIA/TIA 258B colour coding shown). Also refer to the notes following the table for

additional wiring guide information.

1

Pin # Signal EIA/TIA 568A

AT&T 258A or

EIA/TIA 568B

10BaseT

or 100BaseT

1

Transmit +

White/Green

White/Orange

X

2

Transmit –

Green/White or White

Orange/White or Orange

X

3

Receive +

White/Orange

White/Green

X

4

N/A

Blue/White or Blue

Not used (required)

5

N/A

White/Blue

Not used (required)

6

Receive –

Orange/White or Orange

Green/White or Green

X

7

N/A

White/Brown

Not used (required)

8

N/A

Brown/White or Brown

Not used (required)

Table 2-1: Standard RJ45 Wiring Colour Codes

1275T / 1285T Series

Digital Clock Display

INSTALLATION Revision 1.0 Page - 5

Note the following cabling information for this wiring guide:

• Only two pairs of wires are used in the 8-pin RJ 45 connector to carry Ethernet signals.

• Even though pins 4, 5, 7 and 8 are not used, it is mandatory that they be present in the cable.

• 10BaseT and 100BaseT use the same pins, a crossover cable made for one will also work with the

other.

• Pairs may be solid colours and not have a stripe.

• Category 5 cable must use Category 5 rated connectors.

The maximum cable run between the 1275T/1285T and the supporting hub is 300 ft (90 m). The

maximum combined cable run between any two end points (i.e. 1275T/1285T and PC/laptop via

network hub) is 675 feet (205 m).

Devices on the Ethernet network continually monitor the receive data path for activity as a means of

checking that the link is working correctly. When the network is idle, the devices also send a link test

signal to one another to verify link integrity. The 1275T/1285T rear panel is fitted with two LEDs to

monitor the Ethernet connection.

10/100

This Amber LED is ON when a 100Base-TX link is last detected. The LED is OFF when a 10Base-T

link is last detected (the LINK LED is ON). Upon power-up the LED is OFF as the last detected rate is

not known and therefore defaults to the 10Base-T state until rate detection is completed.

LN/AC

This dual purpose Green LED indicates that the 1275T/1285T has established a valid link to its hub,

and whether the 1275T/1285T is sending or receiving data. This LED will be ON when the

1275T/1285T has established a good link to its supporting hub. This gives you a good indication that

the segment is wired correctly. The LED will BLINK when the 1275T/1285T is sending or receiving

data. The LED will be OFF if there is no valid connection.

2.2.3. Serial Port Connections

COM This female 9 pin D connector is used for connecting a computer to upload firmware to the

1275T/1285T. It is also used as a diagnostic port for troubleshooting. See section 6 for

information on upgrading the firmware.

Pin #

Name

Description

1

2

TxD

RS-232 Transmit Output

3

RxD

RS-232 Receive Input

4

5

Sig Gnd

RS-232 Signal Ground

6

7

8

9

Table 2-2: COM Port Pinout

1275T / 1285T Series

Digital Clock Display

Page - 6 Revision 1.0 INSTALLATION

2.3. POWER

The 1275T/1285T series displays come with an auto-ranging DC voltage adapter that

automatically senses the input voltage. Power should be applied by connecting a 3-wire

grounding type power supply cord to the power entry module on the DC voltage adapter.

The power cord should be minimum 18 AWG wire size; type SST marked VW-1, maximum

2.5 m in length. The DC cable of the voltage adapter should be connected to the DC power

jack on the rear panel.

2.4. POWER OVER ETHERNET (POE)

The device is ‘Power Over Ethernet’ enabled. This simply allows a single cable to provide both data

connection and electrical power to the display unit. It is IEEE802.3af compliant.

1275T / 1285T Series

Digital Clock Display

SPECIFICATION Revision 1.0 Page - 7

3. SPECIFICATIONS

The following section stipulates the key specifications regarding the product’s hardware and software

monitoring elements.

Figure 3-1: 1275T/1285T Rear Panel

3.1. FUNCTIONAL

Code Input

SMPTE/EBU ST 12-2 LTC Time Code 20kΩ balanced or unbalanced or

optional NTP DQS-B6

3.2. SERIAL PORT

Connector

Female DB-9

Level

RS-232

Baud Rate

57.6kBaud

Format

8 data bits, no parity, 2 stop bits

3.3. TIME KEEPING

Accuracy

< 2 seconds per day with power on, no time code present

< 10 seconds / day with power removed.

Time One Offset

0 to 23 ½ hours in ½ hours increments set with menu.

3.4. ETHERNET

Network Type

Ethernet 100 Base-TX IEEE 802.3u standard for 100Mb/s baseband

CSMA/CD local area network. Ethernet 10 Base

-T IEEE 802.3 standard or

10Mb/s baseband CSMA/CD local area network

Connector

RJ-45

NTP Standard

RFC-1305 complaint, client mode support

3.5. ELECTRICAL

Backup Battery Type

CR-2032 3 volt lithium cell

Life Expectancy

> 5 years

Power

12V DC, 15W auto ranging 100 to 240V AC, 50/60Hz adapter included

IEEE 802.3af PoE

Power Supply

UL Listed

1275T / 1285T Series

Digital Clock Display

Page - 8 Revision 1.0 SPECIFICATION

3.6. PHYSICAL

Dimensions

1275T: 9.6” W x 9.6” H x 2.125” D

(244mm W x 244mm H x

54mm D)

1285T

12.575”W x 12.575” H x 2.5” D

(320mm W x 320mm H x 63mm D)

Weight

5.0lbs (approx.)

Mounting

Rear slots for wall mounting.

1275T / 1285T Series

Digital Clock Display

OPERATION Revision 1.0 Page - 9

4. OPERATION

The following section describes how to the 1275T/1285T functions and how to operate it in your

environment.

4.1. AN OVERVIEW OF THE SETUP MENU SYSTEM

The key to the operational flexibility of the 1275T/1285T series displays lies in the Setup menu system

that provides a quick, intuitive method of configuring the display. The Setup menu uses the

alphanumeric display to show menu items, and the six large digits are used as alphanumeric displays

to indicate the value of the menu item.

The Setup menu system consists of a main menu with several choices for each menu item. The

SETUP, ITEM, and SELECT pushbuttons are used to navigate the menu.

4.1.1. Setting the Brightness

When not in the Setup menu, the keys are used to adjust the brightness of the LEDS.

• To decrease the brightness of LEDs, press the SELECT button (each time you press the button

the brightness of the LEDs will decrease).

• To increase the brightness of LEDs, press the ITEM button (each time you press the button the

brightness of the LEDs will increase).

4.1.2. The Setup Menu System

To enter the Setup menu system, press the SETUP key. This will bring you to the main Setup menu

where you can use the ITEM key to move down the list of available top level menu items. A two

character display in the alpha digits indicates the menu item you are displaying. The six large displays

show the active value for that menu item. Once you have chosen the desired top level menu item,

press the SELECT key to enter the bottom menu level. The six large digits will blink indicating that

you are at the bottom level and that you are displaying the active item value.

Figure 4-1: Setup Menu System

Setup

Button

1 Item

Button

2 Select

Button

3

1275T / 1285T Series

Digital Clock Display

Page - 10 Revision 1.0 OPERATION

To adjust any parameter, press the ITEM keys to adjust the parameter to its desired value. When you

are showing the active value, the six large digits will flash on and off.

When you have selected the desired parameter value press the SELECT key to make that value the

active value. The six large digits will flash indicating that the value shown is now the active value.

Press the SETUP key to move back to the top menu level. You can select other items from the top

level menu by pressing the ITEM key, followed by the SELECT key. Alternately you can exit the Setup

menu by pressing the SETUP key.

4.2. FRONT PANEL CONTROLS

The 1275T/1285T series displays are equipped with three pushbuttons located at the right side of the

front panel. They are used to operate the menu system and to control what is currently being

displayed on the LED display.

Figure 4-2: 1275T/1285 Front Panel Controls

4.2.1. Pushbuttons

The pushbutton group consists of the SETUP, ITEM and SELECT, pushbuttons and is used to

navigate the Setup menu system.

4.2.1.1. SETUP – Pushbutton:

Enters the Setup menu. When you are in the Setup menu the SETUP pushbutton is used to move to

the next higher sub-menu level or return to normal operation if at the top level of sub-menus.

4.2.1.2. ITEM – Pushbutton:

When in the Setup menu, the ITEM pushbutton is used to move to the next item in the menu system.

When in the bottom level of the menu the ITEM pushbutton is used to change the value of the menu

item. When at the bottom level, the display flashes when the active value is shown and stops flashing

when inactive values are shown.

When not in the Setup menu, pressing the ITEM pushbutton makes the display brighter.

SELECT – PUSHBUTTON:

When in one of the Setup menus the SELECT pushbutton is used to move to the next lower sub-menu

levels or to select a menu parameter that is to be changed. When at the bottom level of the menu the

SELECT pushbutton is used to make the displayed parameter value active.

When not in the Setup menu, pressing the SELECT pushbutton makes the display dimmer.

1275T / 1285T Series

Digital Clock Display

OPERATION Revision 1.0 Page - 11

4.2.2. Front Panel Displays

The main LED display on the 1275T/1285T series displays consists of sixty LEDs around the outside

of the face and a six character 16 segment alphanumeric display. In normal display modes the six

digits are used to display the time or date.

When in the Setup menu, the alphanumeric display is used to display menu items, and the six large

digits are used as alphanumeric displays to indicate the value of the menu item. When setup, the

alphanumeric displays can show the date.

4.3. SETUP MENU – TOP LEVEL

The following section gives a brief description of the menu items available when you enter the Setup

menu. Sections 4.3.1 to 4.3.7 provide detailed descriptions of the Setup menus. The tables in these

sections are arranged in an indented structure to indicate the path taken to reach the control. Menu

items or parameters (in this section) that are underlined indicate the factory default values.

IP Configures the Input Source for the display.

FR Configures the Frame Rate of the output LTC.

DF Configures the Date Format used to encode dates on the output LTC.

LZ Configures the output LTC time zone offset.

TZ Configures the time zone offset.

DZ Configures the Daylight Saving Time rules.

DS Configures the Time or Date Display.

TD Configures the Time Display Format (12 or 24 hour).

DD

Configures the Date Display Format (MM DD YY, DD MM YY, or YY MM

DD).

ST Configures the Time when there is no input.

SD Configures the Date when there is no input.

IC Configures the Internet Protocol items.

1275T / 1285T Series

Digital Clock Display

Page - 12 Revision 1.0 OPERATION

4.3.1. Setting the Input Source

IP

With this menu item, you can select the source of time and date

information.

When set to LTC, the 1275T/1285T series displays will use time and date

information from the LTC input.

When set to LTC ND, the 1275T/1285T

series displays will use time but

not date information from the LTC input. When in this mode, it is important

to enter the date manually. This is useful when the data had no date

information since this looks like Legacy format date of January 1, 1980.

When set to DQS

the 1275T/1285T accepts Evertz DQS protocol

timecode.

When set to NONE, the 1275T/1285T

series displays will free run on its

internal crystal. The user must set the time and date using the ST and SD

menu items. When the power fails, the time will be kept by the battery

backed up clock and will be restored on power up.

LTC

LTC ND

DQS

NTP

NONE

4.3.2. Setting the Time Zone Offset

TZ

With this menu item, you can select the time zone offset that will be

applied from the time displayed.

The Time zone offsets can be set from 0 to 23.5 hours in one half hour

intervals. The time zone offset will be applied when displaying time or

date from one of the input sources selected by the IP menu item

00:00

..

11:30

12:00

-12:00

-11:30

..

00

Page is loading ...

evertz 1275T User manual

This manual is also suitable for

evertz 1275T User manual

Related papers

Other documents