Spedal CL796W User manual

Brand: Spedal

Model: CL796W

Type: User manual

Spedal CL796W is an AI-driven dashcam that seamlessly captures every detail of your journey with its 1080P Full HD resolution and 170-degree wide-angle lens. Utilizing night vision technology, it excels in low-light conditions, ensuring clear recordings even at night. Spedal CL796W acts as a reliable witness, safeguarding you with its loop recording, G-sensor, and parking mode features. Additionally, it boasts a built-in GPS, enabling accurate location tracking and speed display.

SMART MULTIMEDIA DASHCAM

025B3103

CL796W

English 01

· Do not press the lens too hard to avoid damage or disloca-

tion of the lens.

· Do not directly touch the lens surface, so as not to affect

the recording effect.

· Do not remove the memory card during the shutdown

process to avoid ﬁle damage.

Precautions

Safety Guidelines

· Do not operate this product when driving.

· Do not install or operate this product with wet hands.

· Do not install this product in a place with high tempera-

ture, humidity, ﬂammable, explosive gas or liquid.

· Do not install this product in an area that interferes with

the driver's sight or driving safety.

· Do not install this product on the airbag cover or within the

working range of the airbag.

· Do not leave this product in a closed vehicle with high

temperature for a long time.

· Do not operate this product over rated voltage.

· Do not use non-original cables and accessories.

· Do not use sharp objects such as awls or scissors to cut

this product and its accessories.

· Do not disassemble, repair or modify this product and

accessories by yourself.

· Do not install, use or place this product within the reach of

children under the age of 16.

Warnings

English 02

· When using the memory card for the ﬁrst time, please

format it on this product to ensure stable reading and

writing.

· When not using the product for a long time, please pull out

the memory card to ensure the performance of the

memory card.

◆ USB-A To USB-C

Cable

Preparations For Product Use

Products And Components

◆ CL796W ◆ Camera

◆ Audio Cable

◆ Suction Bracket ◆ Power Cable

◆ Camera Cable ◆ TF Card

English 03

Product Introduction

Screen

◆ Non-slip Mat ◆ User Manual

Note

Do not use non-original cables and components. Gifts

and components are not covered under warranty. The

package contents of this product are subject to

change without prior notice, and the actual package

contents shall prevail.

◆ Dashboard Pad

Mounting Disk

Power Button

USB-C Port TF Card Slot

AUX OUT Port

AV IN Port

English 04

· Insert the TF card into the TF card slot.

· Please use the TF card that comes with this product. The

self-provided TF card should meet the following require

ments: Class 10 or above, the capacity does not exceed

128GB.

Installation Guide

◆ TF Card Installation

◆ Suction Bracket Installation

1. Align the suction bracket clips with the holes on the back

of the device and push them up to secure the bracket.

2. Thoroughly clean and dry the car dashboard surface,

remove dust or debris, and make sure the surface is ﬂat.

3. Remove the 3M adhesive release paper from the dash-

board pad mounting disk and adhere it to a clean instru-

ment panel surface.

4. Allow to sit for 3 hours or more to ensure a strong bond.

Then remove the protective ﬁlm from the dashboard pad.

5. Tear off the protective ﬁlm from the suction bracket, place

the suction cups ﬁrmly in the center of the dashboard pad

mounting disk, and press the lock button.

6. Adjust the angle of the device screen.

Note

The installation position of equipment and brackets

should not block the driver's sight and affect driving

safety.

◆ Device Installation

Insert the power cable into the car cigarette lighter, and

connect the other end to the power interface of the device.

English 05

◆ Audio Cable Installation

1. Insert the audio cable into the car AUX port, and connect

the other end to the AUX OUT port of the device.

2. Set the car's audio input mode to AUX audio input. After

the connection is successful, you can play music, naviga-

tion, calls and more through your car's audio system.

English 06

◆ Camera Installation

1. Tear off the protective ﬁlm of the camera lens.

2. Peel off the 3M adhesive release paper from the camera

mount, attach the camera to the windshield, and press

ﬁrmly to secure it.

3. Connect the device via the camera connection cable.

4.Adjust the angle of the camera lens.

more product information

www.spedal.cc

For any questions please contact [email protected]

Spedal CL796W User manual

Spedal CL796W User manual

Related papers

Other documents