Empire DVCT36CFP95N-1 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

(SEE HOMEOWNER MANUAL FOR OPERATING INSTRUCTIONS)

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

DIRECT VENT

ZERO CLEARANCE GAS

FIREPLACE HEATER SERIES:

DVCT36CFP95(N,P)-1

DVCT40CFP95(N,P)-1

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

This appliance may be installed in an

aftermarket, permanently located,

manufactured home (USA only) or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certied kit is used.

This replace is design

certied in accordance

with American National

Standard/CSA Standard

ANSI Z21.88/CSA 2.33

and by Underwriters

Laboratories as a Direct

Vent Gas Fireplace

Heater and shall be

installed according to

these instructions.

GAS-FIRED

UL FILE NO. MH30033

HOT GLASS

DO NOT TOUCH

NEVER

WILL

CAUSE BURNS.

GLASS

UNTIL COOLED.

ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and shall

be installed for the protection of children and other at-risk

individuals.

37742-0-1116Page 2

TABLE OF CONTENTS

SECTION PAGE PAGE

STANDARD WORK CHECKLIST

3

BEFORE YOU START

4

CARTON CONTENTS AND HARDWARE

6

INTRODUCTION

7

HOMEOWNER REFERENCE INFORMATION

7

SPECIFICATIONS

8

ACCESSORIES

8

FIREPLACE DIMENSIONS

9

BLOWER INSTALLATION

10

CLEARANCES

12

VENT TERMINAL CLEARANCES

13

GAS SUPPLY

15

LOCATING FIREPLACE

16

ELECTRICAL CONSIDERATIONS

16

WIRING DIAGRAM

17

INSTALLATION

18

FRAMING AND FINISHING

22

VENT SYSTEM IDENTIFICATION

24

SPECIAL VENT SYSTEMS

24

VENTING FIREPLACE - TOP

25

TOP VENT - HORIZONTAL TERMINATION

28

TOP VENT - VERTICAL TERMINATION

29

VERTICAL TERMINATION

30

FLEX VENT INSTRUCTIONS

32

LOG IDENTIFICATION

34

LOG PLACEMENT

36

AIR SHUTTER ADJUSTMENT

54

CONTROL SYSTEM TROUBLESHOOTING

56

VALVE COMPARTMENT ACCESS

58

TESTING GAS SUPPLY

59

EXPLODED VIEW

60

PARTS LIST

61

MAINTENANCE AND SERVICE

62

IMPORTANT SAFETY INFORMATION

63

REQUIREMENTS FOR MASSACHUSETTS

65

MASTER PARTS DISTRIBUTOR LIST

66

HOW TO ORDER REPAIR PARTS

66

APPLIANCE SERVICE HISTORY

67

WARRANTY

BACK COVER

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

SEE HOMEOWNERS MANUAL

37742-0-1116 Page 3

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instruction manual.

Customer: _____________________________________

Lot/Address: ___________________________________

_______________________________________________

Model: ________________________________________

Date Installed: __________________________________

Fireplace Location: ______________________________

Installer: _______________________________________

Dealer Phone #: _________________________________

Serial # ________________________________________

Empire recommends the following:

• Photograph the installation and copying this checklist for your le.

• Keep this checklist visible on the replace until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/Builder/Other, etc) and corrective action needed:

___________________________________________________________________________________________________________

Comments communicated to party responsible _____________________by _____________________ on ______________________

DVCT(36,40)CFP95(N,P)-1

FIREPLACE INSTALLATION COMMENTS

Veried clearances to combustibles. (pg 12) ....................................................................... o ____________________

Fireplace is leveled and secured. ........................................................................................ o ____________________

VENTING/CHIMNEY/PowerFlow™ HEAT DISTRIBUTION

Venting conguration complies to vent diagrams. (pg. 27) .................................................. o ____________________

Venting installed, locked, secured in place with correct clearance. ..................................... o ____________________

Firestops installed. ............................................................................................................... o ____________________

Exterior wall/roof ashing installed and sealed. ................................................................... o ____________________

Terminations installed and sealed. (pg 28-31) ..................................................................... o ____________________

Light unit and test venting before enclosing the replace. (pg 59) ...................................... o ____________________

ELECTRICAL (pg 16-17)

Unswitched power (110-120 VAC) provided to the appliance. ............................................ o ____________________

GAS (pg 15)

Proper appliance for fuel type. ............................................................................................. o ____________________

Was a conversion performed? .............................................................................................. oYes oNo

Leak check performed and inlet pressure veried ................................................................ o ____________________

FINISHING ( pg 19)

Non-combustable board used as required. .......................................................................... o ____________________

Veried all clearances meet installation manual requirements. ........................................... o ____________________

Mantels and wall projections comply with installation manual requirements. ...................... o ____________________

Granite or Clean Face nishing complete and complies with clearance

requirements in installation manual. .................................................................................... o ____________________

Barrier screen for glass properly installed. .......................................................................... o ____________________

FIREPLACE SETUP

All packaging and protective materials removed (inside & outside of appliance) . ............... o ____________________

Media installed correctly. ..................................................................................................... o ____________________

Firebox glass assembly cleaned, installed, and secured. ................................................... o ____________________

Accessories installed properly. ............................................................................................ o ____________________

Manual envelope and all of its contents are removed from inside/outside the

appliance and given to party responsible for use and operation. ........................................ o ____________________

Started Appliance and veried no gas leaks exist. .............................................................. o ____________________

37742-0-1116Page 4

BEFORE YOU START

Television Considerations

Installing a television above a replace has become increasingly

popular; however, the area above any replace gets hot and most

TV manufacturers recommend against placing their products near

a heat source.

If you install a television above this replace, Empire Comfort

Systems accepts no responsibility for damage or injuries. Follow

the television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

If you have a TV above your replace, turn off the replace and let it

cool completely before servicing or touching any buttons on the TV.

Samples, Warnings, and Denitions:

DANGER

Indicates a hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE: Addresses practices not related to personal injury.

Read all instructions before starting installation and

follow them carefully to ensure safety. Failure to follow

the instructions will void the warranty and may cause

a re hazard.

The warranty will be voided by, and the warranter disclaims

any responsibility for the following actions:

• Installation by anyone other than the dealer or his agent.

• Installation of any damaged replace or component.

• Modication of the replace or direct vent system.

• Installation other than as instructed by Empire Comfort

Systems.

• Improper positioning of logs, glass door, or accessories.

• Installation and/or use of any component part not

manufactured or approved by Empire Comfort Systems.

All correspondence should refer to complete Model Number,

Serial Number and type of gas. Fill out the Homeowner

Reference Section on (Page 5).

Unpacking The Fireplace

1. Remove the outer boards/crate by removing screws.

2. Cut away shrink-wrap material around the unit. Retain

instruction manual and instruction sheets.

3. Remove (2) screws securing unit to pallet.

4. Get help to lift unit off of the pallet using the handles.

5. Remove non-combustible board from the pallet and place in

a safe location. It will be needed for installation.

6. Logs may remain in unit until installation in wall. Instruction

sheet from step #2 shows how to remove barrier screen and

glass door.

37742-0-1116 Page 5

BEFORE YOU START

Accessories

Most accessories install much more easily before tting the replace

to the opening.

For example, it takes just 10-15 minutes to install the blower through

the back of the unit. Once the replace is framed in, it takes up

to an hour.

TrueFlame Technology

This replace is equipped with TrueFlame Technology for maximum

ames and ember glow with minimum emissions. The system

includes independently controlled front and rear burners set into a

large ember bed plus a ceramic catalyst and externally adjustable

bafe mounted at the top. Once adjusted by the dealer/technician at

installation, the TrueFlame system requires no scheduled service.

Preparation

This fireplace and its components are safe when installed in

accordance with this Manual. Report any parts damaged in shipment

to your dealer. Do not install the replace with damaged, incomplete

or substitute parts.

Installation Considerations

• Gas supply piping – right side entrance

• Electrical supply and connections

• 120V, 60Hz, 1 Amp

• Right side entrance

• Allowable replace mounting surfaces:

• A at, hard, combustible or non-combustible surface

• A raised platform of combustible or non-combustible material.

• The four corners of the replace onto non-combustible material

so that contact is made on all four perimeter edges on the

bottom of the replace – such as on cinder blocks

(where allowed by local codes).

• If the replace is installed directly on carpeting, tile or other

combustible material other than wood ooring, it should be

installed on a metal or wood panel extending the full width and

depth of the replace.

• This replace is designed to be installed in a zero-clearance

enclosure. Combustible material can come in contact with the

side standoff spacers, and the replace can be secured to

combustible framing with the framing brackets provided with

the replace.

Planning the installation

First determine where the fireplace will be located and what

accessories will be installed.

Your location must allow for:

• Venting – either vertical or horizontal. Choose a vent conguration,

(See Pages 28-31) and make sure the required access through

attics and walls is not blocked by other utilities such as water

lines, sewer vents, gas lines, etc. If access is blocked, you will

need to move the utilities or relocate the replace.

• Gas supply piping (right side entrance) – see pipe size and

specs on (Page 15).

• Electrical supply requirements

(120V, 60Hz, 1 Amp) (right side entrance)

• Proper framing required for installation of the replace.

See framing dimensions on (Page 18).

• Finishing the fireplace – drywall thickness, tile or stone

thickness, and the desired decorative accessories can affect

how you frame the opening and how you attach the nailing

anges to set the proper depth. (See Page 19) for nishing

details, before you begin.

37742-0-1116Page 6

LOG SET

ASSEMBLY

Rock

wool

Rock

wool

1

2

3

4

5

6

7

10

8

9

CARTON CONTENTS

INDEX

NUMBER

DESCRIPTION

QUANTITY

SUPPLIED

1 Unit 1

2 Log Set Assembly 1

3 AAA Batteries 3

4 AA Batteries 4

5 Rockwool 2 Bags

6 Drywall Screws 5

7

Non-Combustible Board (on pallet)

1

8 Remote 1

9 Battery Holder & Switch 1

*10 Wall Thimble Spacer 1

*For DVCT36 Only

See Parts Lists on page 61 for ordering replacement parts. Do not order batteries, bolts, screws, washers or nuts.

They are standard hardware items and can be purchased at your local hardware store.

CARTON CONTENTS AND HARDWARE

IMAGE NOT TO SCALE

Under Pallet

NOTE: RE-INSTALL SCREWS AFTER UNPACK

37742-0-1116 Page 7

INTRODUCTION

The information in this manual pertains to all models and gas

control systems unless otherwise noted.

Instructions to Installer

1. Leave this manual with Homeowner.

2. Have the homeowner complete the Product Registration

Card or register online at www.empirecomfort.com

3. Show the homeowner how to start and operate the replace.

Notes to Installer

• This replace is designed to:

- Operate with combustion air siphoned from outside of

the building.

- Expel all exhaust gases to the outside of the building.

• The installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code

ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation

Code, or CSA B149.1 in Canada. * Available from the

American National Standards Institute, Inc. 11 West 42nd

St., New York, N.Y. 10036

• Any alteration of the original design, installation other than

as shown in these instructions, or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

• This replace is not for use with solid fuels.

• These replace models may be installed in a bedroom or

bed-sitting room in the U.S.A. and Canada.

WARNING

Any change to this replace can be dangerous.

Improper installation or use can cause serious injury or death

from re, burns, explosion or carbon monoxide poisoning.

Fireplace Certication

This replace is design certied in accordance with American

National Standard/CSA Standard ANSI Z21.88/CSA 2.33 and by

Underwriters Laboratories as a Direct Vent Gas Fireplace Heater

and shall be installed according to these instructions.

Consult your local building code agency, prior to installation,

to ensure compliance with local codes-including permits and

inspections.

The replace, when installed, must be electrically grounded in

accordance with local codes or, in absence of local codes, with

the National Electric Code ANSI/NFPA 70 or Canadian Electric

code, CSA C22.1, if an external electrical source is utilized.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of equipment

shall be performed only by a qualied agency. The term “qualied

agency” means any individual, rm, corporation or company

which either in person or through a representative is engaged

in and is responsible for (a) the installation or replacement of

gas piping or (b) the connection, installation, repair or servicing

of equipment, who is experienced in such work, familiar with all

precautions required and has complied with all the requirements

of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation must be

made by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

High Altitude (USA)

When installing this replace at an elevation above 2000 feet

(in the United States) it may be necessary to decrease the input

rating by changing the existing burner orice to a smaller size.

Generally, input should be reduced 4 percent for each 1000

feet above sea level. However, if the heating value of the gas

has been reduced, this general rule may not apply. Check with

Empire Comfort System’s local gas utility for proper orice size

identication.

High Altitude (CANADA)

Altitude: 0-4500 feet (0-1370 m)

When installing this replace at an elevation above 4500 feet

(in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the

proper orice for your location.

HOMEOWNER REFERENCE INFORMATION

We recommend that you record the following information about your replace.

Model Number: _____________________________ Date purchased: ________________________

Serial Number: _____________________________ Location of replace: _____________________

Dealer Name: ______________________________ Dealer Phone: _________________________

Notes: ______________________________________________________________________________

37742-0-1116Page 8

SPECIFICATIONS

MODEL NUMBER DVCT36NAT DVCT36LP DVCT40NAT DVCT40LP

Input BTU/Hr Maximum (w/ both burners on) 40,000 40,000 47,500 45,000

Input BTU/Hr Minimum (w/ both burners on) 26,000 33,000 30,000 35,000

Input BTU/Hr Minimum (front burner on only) 11,000 13,000 15,000 16,500

KWH (Maximum) 11.72 11.72 13.92 13.19

KWH (Minimum) 7.62 9.67 9.38 10.26

Orice - Front #48 #56 2.25mm #56

Orice - Rear 2.40mm 1.45mm 2.45mm 1.55mm

Air Shutter Opening Front Full Closed Full Opened Full Closed Full Opened

Air Shutter Opening Rear Full Closed Full Opened 1/8 Closed Full Opened

Height without standoff (inches) 40-3/4 40-3/4 42-3/4 42-3/4

Width (inches) 45 45 49 49

Depth (inches) 22-1/8 22-1/8 24 24

Gas Inlet Shutoff Valve (pipe) 1/2 NPT 1/2 NPT 1/2 NPT 1/2 NPT

NOTE: Air shutter is at factory-minimum settings. Some vent congurations may require minor air shutter adjustments for optimum performance.

GAS SUPPLY PRESSURES (inches water column)

GAS TYPE MAXIMUM MINIMUM MANIFOLD

NAT 14 4.5 3.5

LP 14 10.8 10

VENTING

5 x 8 Direct Vent System

LIGHT BULB REPLACEMENT

35w Clear Halogen, Bi-Pin 6.35mm base,120vac, UL

ACCESSORIES

The following accessory parts can be obtained from your Empire Comfort Systems dealer. For additional information beyond

what your dealer can furnish, contact Empire Comfort Systems Inc., 918 Freeburg Ave., Belleville, Illinois 62220-2623.

MODEL NUMBER MODEL NUMBER DESCRIPTION

DVP36P... DVP40P... A liner is required. Contact your Empire Comfort Systems Dealer for available liner.

FBB21 FBB21 Blower, Auto Variable-Speed - Twin

37506 36884 Conversion Kit, IP System Nat to LP

37507 36885 Conversion Kit, IP System LP to Nat

DF36CNB DF402NB Beveled Window Frame 1.5-inch, (Brushed Nickel)

DFF36FPD DFF40FPD Decorative Front, Forged Iron Frame, Distressed Pewter

DFF36RPD DFF40RPD Decorative Arch Insert, Forged Iron, Distressed Pewter

DFF36CPD DFF40CPD

Decorative Rectangle Insert, Forged Iron, Distressed Pewter (Requires DFF40FPD)

DDF36CPD DDF40CPD Decorative Door Set, Forged Iron, Traditional, Distressed Pewter

DCA1ABL DCA1ABL Andirons, Black

* A liner kit must be purchased and installed in order to operate the unit

37742-0-1116 Page 9

I

C

G

P

J

F

B

O

N

Q

E

A

D

L

M

R

K

FIREPLACE DIMENSIONS

INDEX

LETTER

DIMENSION DESCRIPTION

DIMENSION IN INCHES

DVCT36 DVCT40

A The maximum height of replace face 40 3/4 42 3/4

B The maximum width of the replace face 45 49

C The maximum depth of the replace 22 1/8 24

D The height of the replace opening 34 1/2 36 1/2

E The width of the replace opening 36 7/8 40 7/8

F The interior depth of the replace

17 1/4 16 7/8

G The rear exterior width of the replace 33 36 1/8

H The height to the replace standoffs N/A N/A

I Width from the left side to the centerline of vent 22 1/2 24 1/2

J Depth from back to centerline of top vent 10 1/8 10 1/16

K Height from the bottom to the gas line opening 11 1/4 11 1/4

L Depth from the front to gas line opening 17 19 3/8

M Depth from rear to gas line opening 5 1/8 5 3/16

N Glass height 28 3/8 30 3/8

O Glass width 31 3/4 36

P Depth from front to centerline of vent 12 14

Q Distance from oor to replace opening 1 1/2 1 1/2

R Height from oor to vent collar 40 5/16 42 5/16

N/A - Not applicable for this unit.

Figure 1

37742-0-1116Page 10

BLOWER INSTALLATION

Bench Installation

1. Remove Blower Access Panels (Figure 2).

Figure 2

2. Place Blowers onto blower brackets. (Figure 3)

Figure 3

3. Bend tab as shown in (Figure 4) and secure with

(2) screws.

HAND BEND

TAB INWARD

HAND BEND

TAB INWARD

Figure 4

4. Remove protective connectors on Wire Assembly from

replace and discard. Connect Wire Harness to both blowers

and the other end to the Wire Assembly supplied with the

replace. (Figure 5)

TO WIRE ASSEMBLY

(MODULE)

TO WIRE ASSEMBLY

(MODULE)

Figure 5

5. Replace Blower Access Panels removed in step 1 (Figure1).

Installation After Placement of Unit in Wall

1. Remove the following items (Figure 6).

• Screen barrier (See Homeowner’s Manual, Maintenance

and Service).

• Glass Frame Assembly (See Homeowner’s Manual,

Maintenance and Service).

• Liners (See separate liner instruction document).

Figure 6

2. Remove front and rear burner (Figure 7).

Figure 7

CAUTION: Sharp edges. Use protective gloves when installing.

37742-0-1116 Page 11

BLOWER INSTALLATION

3. Remove burner base. (Figure 8)

Figure 8

4. Remove Blower Brackets by taking out (6) screws each.

(Figure 9)

Figure 9

5. Place Blower onto Blower Brackets. (Figure 10)

.

Figure 10

6. Bend tab as shown in (Figure 11) and secure with

(2) screws.

HAND BEND

TAB INWARD

HAND BEND

TAB INWARD

Figure 11

7. Remove protective connectors on Wire Assembly from

replace and discard. Connect Wire Harness to both blowers

and the other end to the Wire Assembly supplied with the

replace. (Figure 12)

TO WIRE ASSEMBLY

(MODULE)

TO WIRE ASSEMBLY

(MODULE)

Figure 12

8. Replace Blower Bracket (w/ blowers attached) with (6)

screws each. (Figure 13)

Figure 13

9. Replace Glass Frame, Screen Barrier, and liners removed in

Step 1 (Figure 6).

37742-0-1116Page 12

Mantel Chart

COMBUSTIBLES

ALLOWED

WALL

STUD

FIREBOX

FACE

72”

MIN.

(CEILING TO

FLOOR)

CEILING

FLOOR

OPENING OF

FIREPLACE

35”

MIN.

22”

MIN.

12”

MIN.

10”

A

B

C

D

E

F

WALL

F

ACING

Index

Letter

Distance From

Wall Facing

Distance From Top

of Opening

Dimensions in inches

A 2 12

B 4 13-5/8

C 6 15-5/16

D 8 17

E 10 18-5/8

F 12 22

Figure 16

Clearances

Clearance from top opening of replace to ceiling is 35 inches.

Clearance from opening to adjacent sidewall is 6 inches.

▼

6” (152 mm)

TO

FIREPLACE

OPENING

35” (889mm)

TO

FIREPLACE

OPENING

Figure 17

CLEARANCES

Clearance to Combustibles

Dim. in inches

Back 0

Side 2

Floor 0

Top of Unit

24

Top Framing Edge 0

FINISHED WALL

(COMBUSTIBLE)

NONCOMBUSTIBLE

BOARD INSTALLED

OVER APPLIANCE

SEE MANTEL CHART

FOR MAXIMUM

MANTEL DEPTH

FRAMING HEADER

FINISHED WITH

NONCOMBUSTIBLE

MATERIAL AS

DESIRED

REFER TO

MANTEL CHART

BARRIER SCREEN

&

GLASS FRONT

NAILING

FLANGES

Figure 14

NOTICE: Use only non-combustible materials to nish the face of

the replace.

6

45

o

3

MAX.

PERPENDICULAR

SIDE WALL

FRONT

FACE

(SIDE)

COMBUSTIBLE MATERIALS

ALLOWED IN SHADED AREAS

FIREPLACE

(TOP VIEW)

2”

Figure 15

37742-0-1116 Page 13

Termination clearance for buildings with combustible and noncombustible exteriors.

Vertical Sidewall Installations

Important! Minimum clearance between vent pipes and combustible

materials is 3 inch (76 mm) on top, and 1 inch (25 mm) on bottom

and sides.

Important! When vent termination exits through foundation less

than 20 inch (508 mm) below siding outcrop, the vent pipe must

extend outward so that the horizontal vent termination is located

ush to, or beyond the outcrop siding.

Information on Various Venting Routes and Components

Important: Locate the replace in such a way that minimizes the

number of offsets and horizontal vent length.

Since it is very important that the venting system maintain its balance

between the combustion air intake and the ue gas exhaust, certain

limitations as to vent congurations apply and must be strictly

adhered to.

Figure 18

The graph showing the relationship between vertical and horizontal

side wall venting will help to determine the various vent lengths

allowable.

The horizontal vent run refers to the total length of vent pipe from

the ue collar of the replace to the face of the outer wall.

Venting termination shall not be recessed into wall or siding.

ATTENTION: Vinyl Soft, Vinyl Ceiling, Vinyl Overhang

Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be held

responsible for heat damage caused from terminating under vinyl

overhangs, vinyl ceilings or vinyl ventilated/unventilated softs.

VENT TERMINATION CLEARANCES

37742-0-1116Page 14

VENT TERMINATION CLEARANCES

Canadian Installations1 US Installations2 Canadian Installations1 US Installations2

A= Clearance above grade,

veranda, porch, deck, or

balcony

12-in (30cm) 12-in (30cm)

I= Clearance to service

regulator vent outlet

3ft (91cm) 61-in

B= Clearance to window or

door that may be open

12-in (30cm) for

appliances >

10,000Btuh (3kW) and

≤ 100,000 Btuh (30kW)

9-in (23cm) for

appliances >

10,000Btuh

(3kW) and ≤ 50,000

Btuh (15kW)

J= Clearance to non-me-

chanical air supply

inlet to building or the

combustion air inlet to

any other appliance

12-in (30cm) for

appliances > 10,000

Btuh (3kW) and ≤

100,000 Btuh (30kW)

9-in (23cm) for

appliances > 10,000Btuh

(3kW) and ≤ 50,000Btuh

(15kW)

C= Clearance to permanent-

ly closed window

12-in (30cm) 12in (30cm)

K= Clearance to a me-

chanical air supply inlet

6ft (1.83m)

3ft (91cm) above if within

10ft (3m) horizontally

D= Vertical clearance venti-

lated soft located above

the terminal within a hor-

izontal distance of 2 feet

(61cm) from the center

line of the terminal

18-in 18-in

L= Clearance above

paved sidewalk or

paved driveway

located on public

property

7ft (2.13m) † 7ft (2.13m)

E= Clearance to unventilat-

ed soft

18-in 18-in

M= Clearance under

veranda, porch

deck, or balcony

12-in (30cm) ‡ 12-in (30cm)

F= Clearance to outside

corner

See previous page. 1

In accordance with the current CSA B149.1, Natural Gas and Propane

Installation Code

G= Clearance inside corner See previous page. 2

In Accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code

H= Clearance to each side

of center line extended

above meter/regulator

assembly

3ft (91cm) within a

height 15ft (4.5m)

above the meter/regula-

tor assembly

3ft (91cm) †

A vent shall not terminate directly above a sidewalk or paved driveway that

is located between two single family dwellings and serves both dwellings

ATTENTION: Vinyl Soft, Vinyl Ceiling, Vinyl Overhang

Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be

held responsible for heat damage caused from terminating under

vinyl overhangs, vinyl ceilings or vinyl ventilated/unventilated softs.

‡

Permitted only if veranda,, porch, deck, or balcony is fully open on a mini-

mum of two sides beneath the oor.

*

For clearances not specied in ANSI Z223.1/NFPA 54 or CSA B149.1, one

of the following shall be indicated:

Clearance in accordance with local installation codes and the requirements of the

gas supplier.

37742-0-1116 Page 15

GAS SUPPLY

The gas pipeline can be brought in through the right side of the

replace. The replace has a Flexline with shut-off valve located

on the left side when facing the replace. (See Figures 18 and

19) Consult the current National Fuel Gas Code, ANSI Z223.1

CAN/CGA-B149 (.1 or .2) installation code.

RECOMMENDED GAS PIPE DIAMETER

Pipe Length

(Dimensions

in feet)

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

(Dimensions in Inches)

Nat. L.P. Nat. L.P.

0-10 1/2 3/8 1/2 3/8

11-40 1/2 1/2 5/8 1/2

41-100 1/2 1/2 3/4 1/2

101-150 3/4 1/2 7/8 3/4

Caution: Never use plastic pipe. Check to conrm whether your

local codes allow copper or galvanized tubing.

Notice: Some municipalities have additional local codes.Consult

your local authority and installation code.

The use of the following gas connectors is recommended:

— ANSI Z21.24 Fireplace Connectors of Corrugated Metal

Tubing and Fittings.

— ANSI Z21.45 Assembled Flexible Fireplace Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction. The state of Massachusetts requires that a

exible replace connector cannot exceed three feet in length.

Figure 19

Installing the Main Gas Shut-Off

Each replace should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of the

replace and can be easily accessed. Where none exists, or where

its size or location is not adequate, contact your local authorized

installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

to the action of liqueed petroleum gases. The gas lines must be

checked for leaks by the installer. Testing for leaks on all exposed

connections should be done with leak test solution or a soap

solution. After testing is complete, all solution should be cleaned off.

On unexposed connections, a pressure test should be made.

WARNING

Never use an exposed ame to check for leaks. Fireplace must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

replace connected; control valve will sustain damage.

NOTICE: The gas controls are equipped with a captured screw-

type pressure test point. It is not necessary to provide a 1/8-inch

test point up stream of the control.

When using copper or ex connector use only approved ttings.

The replace and its individual shut-off valve must be

disconnected from supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psig

(3.5kPa).

The replace must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during any

pressure testing of the gas supply piping system at test pressures

equal to or less than 1/2 psig (3.5kPa).

WARNING

If one of the procedures results in pressures in excess of

1/2 psig (14 inches w.c.) (3.5 kPa) on the replace gas valve, it

will result in a hazardous condition.

LEFT SIDE OF FIREPLACE

FRONT

OF FIREPLACE

GAS FLEX

LINE WITH

SHUT-OFF VALVE

(PROVIDED)

“B”

“A”

DVCT36

DIM “A”

DIM “B”

DVCT40

19 3/8”

11 1/4”

17”

11 1/4”

DIMENSION

DVCT36 DVCT40

A 17 19 3/8

B 11 1/4 11 1/4

Figure 20

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. The National

Fuel Gas Code requires that a drip leg be installed near the gas

inlet. (See Figure 21) This should consist of a vertical length of

pipe tee connected into the gas line that is capped on the bottom

in which condensation and foreign particles may collect.

GAS SUPPLY PLUMBING

MANUAL

SHUT-OFF VALVE

GAS SUPPL

Y

INLET

DRIP LEG

3” MINIMUM

TO

CONTROL

VALVE

Figure 21

37742-0-1116Page 16

NOTE: When installing this

appliance against an exterior wall,

insulate to applicable insulation

codes.

LOCATING FIREPLACE

CORNER

INSTALLATION

ANGLED CORNER

INSTALLATION

ISLAND

INSTALLATION

CABINET

INSTALLATION

FLUSH WALL

INSTALLATION

ROOM DIVIDER

INSTALLATION

ELECTRICAL CONSIDERATIONS

Junction Box

A factory-installed junction box is located on the lower right side of

the replace. Wiring must be fed to the junction box and attached

with wire nuts to the control module power leads already fed into

the junction box.

Attach black to black and white to white. The ground wire should

be attached to the ground on the junction box. (Figure 23)

Interface/Battery Holder

The user interface/battery holder must be mounted within a distance

allowed by the attached 12 foot harness. As shipped, this harness is

already fed through a strain relief on the bottom of the component

access box and is attached to the User Interface/Battery Holder.

NOTE: If an auxiliary device is to be used, its wiring may be fed

through the junction box strain relief. Auxiliary device amperage

limit is 5 amps.

NOTE: A one inch diameter hole should be use to pass wiring through

studs.

BLACK (HOT)

JUNCTION BOX

WHITE (NEUTRAL)

GROUND TO JUNCTION BOX

120 VOLT POWER SUPPLY

JUNCTION BOX CONNECTIONS

Figure 23

CAUTION

All wiring should be done by a qualied electrician and shall be in compliance with all local, city and state building codes. Before making

the electrical connection, make sure that the main power supply is disconnected. The appliance, when installed, must be electrically

grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code ANSI/NFPA 70 (Latest Edition).

VERTICAL

FRAMING

MEMBER

USER INTERFACE

HARNESS

USER INTERFACE/

BATTERY HOLDER

MUST BE INSTALLED

INTO WALL

JUNCTION

BOX. (ORANGE LOW-

VOLTAGE BOX

RECOMMENDED.)

COMPONENT

ACCESS BOX

ELECTRICAL POWER TO UNIT

JUNCTION BOX / CONTROL MODULE

Figure 22

NOTE: Island and Room Divider

installation is possible as long

as the horizontal portion of the

vent system does not exceed 18

feet with a minimum vertical run

of 8 feet. See details in Venting

Section.

When you install your Direct Vent

Fireplace in room divider or at

on wall corner positions, maintain

a minimum of 6 inches between

the perpendicular wall and the

opening of the appliance.

Figure 24

37742-0-1116 Page 17

Figure 25

COMPONENT WIRING DIAGRAM

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH EQUI

V

ALENT GAUGE AND

TEMPERATURE RATED WIRE.

SI LE FIL ORIGINAL L'UN DES COMME FOURNI

AVEC CETTE UNITÉ DOI

T

ÊTRE REMPLACÉ, IL

DOIT REPLCED AVEC LA MESURE ÉQUIVALENTE

ET LE FIL ÉVALUÉ PAR TEMPÉRATURE.

ORANGE

PILOT

GAS CONTROL VALVE

ORANGE

GREEN

YELLOW

WHITE

BLACK

WHITE

BLOWER

FUSE

BLACK

WHITE

GREEN

TO JUNCTION

BOX

AUX.

LOOP

TO LIGHTS

SPLIT FLOW SOLENOID

SLEEVE

USER INTERFACE/

BATTERY HOLDER

L

N

COMBUSTION

BLOWER

A

D

E

B

C

INDEX NUMBER DESCRIPTION PART NUMBER

A WIRE HARNESS, ACCENT LIGHT TERMINATION R12269

B WIRE ASSEMBLY, MODULE TO INTERFACE R11552

C WIRE HARNESS, PROFLAME2 R11551

D WIRE ASSEMBLY (BLOWER) R12256

E WIRE HARNESS, MODULE TO JUNCTION BOX R11730

Top of Receiver Module

Figure 26

Bottom of Receiver Module

Figure 27

37742-0-1116Page 18

INSTALLATION

INSTALLATION TABLE - MINIMUM DIMENSIONS (in inches)

MODEL A B C D E F

DVCT36CFP 51 1/2 45 1/2 22 1/8 54 11/16 77-3/8 38 11/16

DVCT40CFP 53 1/2 49 1/2 24 59 11/16 84-3/8 42 1/4

C

A

B

Rough Opening for Floor Level Installation

Figure 28

A

C

B

Rough Opening for Elevated Installation

Figure 29

Rough Opening for Installing in Corner

Figure 30

The replace can be mounted on any of the following surfaces:

1. A at, hard combustible or non-combustible surface.

2. A raised wooden platform.

3. Four corner supports. (Example: Four concrete masonry

blocks.) These supports must be positioned so they contact

all four perimeter edges on the bottom of the replace, if

allowed by local codes.

NOTICE: Verify the gas supply and electrical considerations

before beginning the framing.

Framing Information

Fireplace framing can be built before or after the replace is set

in place. Position framing to accommodate wall covering and

replace facing material. Construct the replace framing with

2 x 4 lumber or heavier. Refer to the INSTALLATION TABLE

below for minimum framing dimensions.

CAUTION

Before construction begins, measure replace dimensions and

verify framing methods and wall covering details.

37742-0-1116 Page 19

INSTALLATION

NAILING FLANGES

FLUSH WALL INSTALLATION

NONCOMBUSTIBLE

BOARD INSTALLED

OVER APPLIANCE

FINISHED

WALL

NAILING

FLANGES

SECURED

IN PLACE

FOR 1/2”DRYW

ALL

FOR 5/8”DRYW

ALL

FINISHED

WALL

NONCOMBUSTIBLE

BOARD INST

ALLED

OVER APPLIANCE

FRAMING

HEADER

11”

Figure 31

Figure 32

Figure 33 Figure 34

WARNING

When nishing the replace never obstruct or modify the gap

around the glass frame in any manner. Provide adequate

clearances around air openings into the combustion chamber.

CAUTION

If the joints between the nished wall and the replace surround

(top and sides) are sealed, a 300°F minimum sealant material

must be used. These joints are not required to be sealed. Only

non-combustible material (using 300°F minimum adhesive if

needed) can be applied as facing to the replace surround.

37742-0-1116Page 20

INSTALLATION

Horizontal Vent Clearance

For horizontal vent, maintain 1 inch of clearance to the bottom

and sides of vent, and 3 inches of clearance to combustibles

above the vent pipe. (See Figure 36)

Vertical Vent Clearance

For vertical vent, maintain a minimum 1 of inch clearance to

combustibles.

NOTICE: Maintain 1 of inch of clearance to combustibles around

vertical vent pipe. (See Figure 35) For horizontal vent systems,

maintain a minimum 1 inch of clearance from the bottom and sides

of the vent to combustibles and a 3 inches of clearance above the

vent pipe to combustibles. (See Figures 35 and 36)

VENT PIPE

1” MINIMUM CLEARANCE

AROUND VENT PIPE

Figure 35

TOP OF VENT

COMBUSTIBLES NOT

ALLOWED IN SHADED

AREA

3” (76 mm)

8” DIAMETER

INTAKE VENT

1” (25 mm)

5” DIAMETER FLUE

1” (25 mm)

Horizontal Vent Clearances - Figure 36

ATTENTION: Cold climate installation recommendation: When

installing this unit against an exterior wall, the exterior wall must

be insulated to conform to applicable insulation codes. The

replace outer wrapper is not considered a thermal barrier and

can allow air inltration. Care should be taken to properly seal

the chase area so air inltration is kept to a minimum and drafts

do not occur througn the replace.

Vent Runs

In planning the installation, you must install certain components

before the replace is secured in position. These include the

direct-vent system, gas piping, and the electrical wiring.

The appliance can be mounted on any of the following surfaces:

1. A at, hard combustible or non-combustible surface.

2. A raised wooden platform.

3. Four corner supports(such as masonry blocks). These supports

must be positioned so they contact all four perimeter edges on

the bottom of the unit.

Page is loading ...

Empire DVCT36CFP95N-1 Installation Instructions Manual

This manual is also suitable for

Empire DVCT36CFP95N-1 Installation Instructions Manual

Related papers

Other documents