TRIANGLE TUBE Horizontal Vent Termination Kit Operating instructions

TRIANGLE TUBE
Brand
TRIANGLE TUBE
Model
Horizontal Vent Termination Kit
Type
Operating instructions

TRIANGLE TUBE Horizontal Vent Termination Kit is a device designed to help you safely and efficiently vent your appliances. It includes a variety of components that allow you to customize the kit to fit your specific needs, including vent pipes, elbows, a wall thimble kit, a termination hood, sealant, a condensate drain, an appliance vent adapter, and an air intake reducer.

With this kit, you can easily install a horizontal vent system for your appliances, ensuring that flue gases are properly exhausted and that your home is safe from carbon monoxide emissions.

TRIANGLE TUBE Horizontal Vent Termination Kit is a device designed to help you safely and efficiently vent your appliances. It includes a variety of components that allow you to customize the kit to fit your specific needs, including vent pipes, elbows, a wall thimble kit, a termination hood, sealant, a condensate drain, an appliance vent adapter, and an air intake reducer.

With this kit, you can easily install a horizontal vent system for your appliances, ensuring that flue gases are properly exhausted and that your home is safe from carbon monoxide emissions.

Installation Instruction for Triangle Tube
Horizontal Vent Termination Kit
1
Kit Part Number Kit Description
HMVKIT01A Standard Horizontal Single Wall Vent Kit
- Vent Pipe – 6”length (2)
- Vent Elbow - 90º
- Vent Pipe – 3’ length
- Adjustable Pipe - 6" to 19"
- Horizontal Wall Thimble Kit (For up to 12"
Thick Walls)
- Termination Hood
- Sealant
- 3" Condensate Drain with Tubing
- Appliance Vent Adapter
- Air Intake Reducer 4" to 3"
HMVKIT05 Horizontal Wall Thimble Kit (for up to 12"
Thick Walls)
HMVKIT06 Horizontal Wall Thimble Sleeve (Replaces 12"
Sleeve for up to 20" Thick Wall )
Indicates the presence of a hazardous situ-
ation which, if ignored, will or can result in
death, severe personal injury or s u b s t a n-
tial pro p e rty damage.
WARNING
Installation and service must be performed
by a qualified installer or agency
WARNING
Installation of Vent
Follow vent manufacturer’s instructions to con-
struct vent system runs and for methods of support-
ing vent runs.
• Clean joints before sealing. See vent pipe
manufacturer’s instructions to clean joints.
Follow the vent pipe manufacturer’s instruc-
tions for sealing the vent piping. The vent
pipe connector must be sealed gas-tight to
prevent the possibility of flue gas spillage and
carbon monoxide emissions, which could
result in severe personal injury or death.
• Do not mix components or joining methods
from other vent manufactures.
• Maintain the vent pipe clearances to com-
bustible material as listed in the vent manu-
facturer’s instructions.
• When penetrating a wall, it is recommended
a wall thimble be used and the following
clearances maintained:
2” for combustible materials
1” for non-combustible materials
• Install vent pipe with seams on top of vent
runs.
• See vent pipe manufacturer’s instructions to
cut vent pipe.
• Install the vent appliance adapter to the vent
hood outlet.
Horizontal Wall Thimble Kit
• Horizontal Wall Thimble Kit includes:
- Split Ring (2)
- Inside End Cap
- Thimble Box
- Outside End Cap
- Mounting Screws
- Reducer 3 x 4
• Requires a 5 1/2” x 5 1/2” hole when vent-
ing through all type of walls.
• Allows zero clearance to all materials when
penetrating a wall.
Installation of Thimble Box
• Vent pipe must extend through Thimble
Box
• Use split ring to seal Inside Cap and
Outside Cap around vent pipe.
• Outside Cap mounts to exterior wall, with
air intake facing downward.
• Position Termination Hood or Termination
Tee properly so flue gases exhaust horizon-
tally.
• Termination should be securely installed as
shown on page 3.
WARNING
Installation Instruction for Triangle Tube
Horizontal Vent Termination Kit
2
Horizontal - Direct Vent Combination Installation
Installation Instruction for Triangle Tube
Horizontal Vent Termination Kit
3
2004-36 Inst. Horzontal Vent Kit
Revision 1/06
  • Page 1 1
  • Page 2 2
  • Page 3 3

TRIANGLE TUBE Horizontal Vent Termination Kit Operating instructions

TRIANGLE TUBE
Brand
TRIANGLE TUBE
Model
Horizontal Vent Termination Kit
Type
Operating instructions

TRIANGLE TUBE Horizontal Vent Termination Kit is a device designed to help you safely and efficiently vent your appliances. It includes a variety of components that allow you to customize the kit to fit your specific needs, including vent pipes, elbows, a wall thimble kit, a termination hood, sealant, a condensate drain, an appliance vent adapter, and an air intake reducer.

With this kit, you can easily install a horizontal vent system for your appliances, ensuring that flue gases are properly exhausted and that your home is safe from carbon monoxide emissions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents