Ripmax FREEDOM 3D U32 User manual

Brand: Ripmax

Model: FREEDOM 3D U32

Type: User manual

U32

Blade

Drone Frame

1. Drone

Name of Parts

2. Transmitter

Power Switch

Throttle/Rudder Stick

Rudder Trim

Left/Right Trim

Forward/Backward Trim

Power Indicator Light

Forward/Backward/Left/

Right Stick

Drone Housing

Battery

Motor

Blade Guard

Power Indicator Light

Body Light

180° Left Flip Button 180° Right Flip Button

High/Medium/Low

Speed Mode Button

(Press Down)

Headless Mode Button

(Press Down)

(2) Keep away from humid environment

The drone inside is consisted of precise electronic components. Humidity or water

vapor may damage electronic components and cause accident.

(3) Safe operation

Please operate the RC drone in accordance with your physical status and ying skill.

Fatigue, listlessness and improper operation may increase the rate of accident.

(4) Keep away from rotating parts

Rotating Parts can cause serious injury and damage. Keep face and body away from

rotating motors.

(5) Keep away from heat

(6) Please do not touch the hot motor to avoid being burnt.

The RC drone is made of metal, ber, plastic, electronic components etc. Keep away

from heat and sunshine to avoid distortion and damage.

Indication Direction of TrimIndication Direction of Power Switch

(4) We undertakes no liability for those accidents caused by improper operation, use and

control of the drone after sale of the product.

(5) We has entrusted the distributor to provide technology support and after-sale service.

If you have any questions about use, operation, repair etc., please contact your local

distributor.

2. Safety Precautions:

Keep away from crowd when ying because a ying RC drone is very dangerous. Improper

assembly, broken main frame, defective electronic equipment or unskilled operation all may

cause unpredictable accidents such as drone damage or human injury. Please pay special

attention to safety operation and have good knowledge of accident responsibility that the

user may cause.

(1) Keep away from obstacles and crowd

The speed and status of a ying RC drone is uncertain and it may cause potential danger.

So the user must keep away from crowd, tall building, power lines etc. when operating

a ying RC drone. Do not y a RC drone in rainy, storm, thunder and lighting weather

for the safety of user, around people and their property.

(2) This drone is suitable for experienced RC drone user aged 14 years or above.

(3) The ying eld must be legally approved by your local government.

Notice:

1. Important Statement:

(1) This product is not a ordinary toy but a piece of complicated equipment which is

integrated with professional knowledge by mechanic, electronic, air mechanics,

high-frequency emission etc., so it should be installed and adjusted correctly to avoid

accidents. The user must always operate in a safe manner. We undertakes no liability

for human injury or property damage caused by improper operation as we could not

control the procedure of installation, use and operation of this drone.

Return Home Mode 360° Flip Button

(5) Make sure the connection is solid between battery and motor etc. The ongoing vibration

may cause bad connection of power terminal make the drone out of control.

(6) Improper operation may cause drone crash, which may arouse motor defective and

noise, and then eect the ying status or even stop ying. Please go to the local

distributor to buy new parts for replacement so that the drone will return to its best status.

(4) Please strictly obey the order of turn on and turn o before operation. Turn on the

transmitter power rst and then turn on the drone power before ying; turn o the drone

power rst and then turn o the transmitter power when nish ying. Improper turn on

and turn o order may cause the drone out of control and threaten people’s safety.

Please cultivate a correct habit of turn on and turn o.

(1) Flying eld must spacious enough and we suggest at least

8M (length)*8M (width)*5M (height).

(2) Make sure the battery of the drone and its transmitter are fully charged.

(3) Make sure the Throttle Control Stick of the transmitter in the lowest position.

3. Check List Before Flight

Transmitter Installation:

Battery installation: open the battery cover on the back side of the transmitter and put 4

alkaline batteries (not included) into the box in accordance with

electrode instructions.

Battery Cover

4*1.5V

Alkaline Batteries

1. Make sure the electrodes are correct.

2. Do not mixed use new and old batteries.

3. Do not mixed use dierent kinds of batteries.

4. Do not charge the non rechargeable battery.

Notice:

* Do not use the battery to crash or hit hard surface.

* Do not put the battery in water and keep it in dry place.

* Do not open the battery.

* Do not leave the battery without supervision when charging.

* Make sure that there is no short circuit of the power wire.

Charging Instruction

1. Connect the drone battery with USB charger rst and then choose one of the below

methods to connect with USB charger. (prior to choose 2A, 5V charger)

2. The red USB indicator light keeps bright when charging.

3. The charging time is about 50 minutes. The light turns to green when fully charged.

4. Li-Po battery is included in spare parts and please pay attention on below safe notice.

* Do not put the battery on high temperature place, such as re or heating device to avoid

damage or explode.

Cut o the power at once when nishing ight to avoid overuse and inuence the

battery eciency.

Do not charge when the battery surface is hot till cooling down, or may inuence

its use life.

Please use the recommended charger only.

Check the charger’s wire, plug, surface regularly. Do not use any broken charger.

Notice:

2. Power on the drone.

3. Put the drone on the at ground, the indicator lights of the drone turn from ashing to

solid bright, which indicates successful frequency pairing. The drone is ready to be

controlled.

Calibration Instruction

Please follow the below steps to calibrate the drone if the drone can not be adjusted by trim

button and cause dicult operation.

1. Power o the drone and then turn o the transmitter power switch.

2. Turn on the transmitter switch, push the Throttle Stick all the way up then all the way

down, and the transmitter enters pairing mode.

3. Power on the drone and put it on a at surface in a horizontal position. You will hear “di,

di, di” beeping noise three seconds later, which indicates successful code pairing. The

drone body light will turn solid.

1. Turn on the transmitter switch and its indicator lights begin to ash quickly. Push the

Throttle Stick all the way up then all the way down. The indicator lights become ash

slowly, which indicates the transmitter enters code pairing.

Frequence Pairing

LiPo Battery Disposal & Recycling

Wasted Lithium-Polymer batteries must not be placed with household trash.

Please contact local environmental or waste agency or the supplier of

yourmodel or your nearest LiPo battery recycling center.

3. Press relative transmitter Trim button to adjust the rudder if the drone tilts to one side

when ying.

Front

Rear

Left

A Blade

Clockwise

B Blade

Counterclockwise

A Blade

Clockwise

B Blade

Counterclockwise

Right

Flying Control

1. Push the Throttle Stick up to y the drone up,

and pull the Stick down to y the drone down.

2. Move the Forward/Backward/Left/Right Stick to

the left to y the drone to the left, and move the

Stick to the right to y the drone to the right.

3. Push the Forward/Backward/Left/Right Stick up

to y the drone forward, and pull the Stick down

to y the drone backward.

4. Move the Throttle Stick to the left to rotate the

drone to the left, and move the Stick to the right

to rotate the drone to the right.

Froward Backward

Pre-Flight Operation:

1. The power indicator light is the drone rear.

2. Power on the drone and check the direction of the rotating blades. The left front and right

rear blades rotating clockwise while the right front and left rear blades rotating

counterclockwise.

4. Do not push the Throttle Stick before successful calibration. Push the Forward/Backward/

Left/Right Stick as shown below (See Pic 1). The drone body lights ash, which indicates

that the drone is calibrating. When the drone body lights remain solid, turn over the drone

and put it on the at surface, repeat the operation to push the Forward/Backward/Left/Right

Stick as shown below (See Pic 2). The drone body lights ash,which indicates that the

drone is calibrating. When the drone body lights remain solid, your drone is ready to y.

Pic 1 Pic 2

5. If the drone tilts forward or backward

Tilt forward Tilt backward

180° Flip and 360° Flip

When the drone is ying, press the left button on the top of the transmitte, the transmitter

will issue sound of di and the drone will do 180° ipping to left. Press right button on the

top of the transmitte, the transmitter will issue sound of di and the drone will do 180°

ipping to right.

180° Flip

High/Medium/Low Speed Mode

By default, the drone is in Medium Speed Mode (M). Press the Throttle Stick and the

transmitter issues sounds of “dididi”, which indicates that the drone enters High Speed

Mode (H); Press the Throttle Stick again and the transmitter issues sounds of di, which

indicates that the drone enters Low Speed Mode (L); Press the Throttle Stick one more

time and the transmitter issues sounds of didi, which indicates that the drone enters

Medium Speed Mode (M).

High/Medium/Low Speed Mode Button

6. If the drone tilts to the left or right

7. If the drone rotates to the left or right

Press the Backward Trim till balance

if the drone drifts forward, and press

the Forward Trim if the drone drifts

backward.

Press the Right Rotation Trim till

balance if the drone rotates to the

left, and press the Left Rotation

Trim till balance if the the drone

rotates to the right.

Press the Right Trim till balance if

the drone drifts to the left, and

press the Left Trim till balance if

the drone drifts to the right.

Drift left Drift Right

Press the 360°Flip button when the drone is ying, and the transmitter will issue sounds of

dididi..., and then push the Forward/Backward/Left/Right Stick to any direction. The drone

will do 360° ipping in the same direction accordingly.

360° Flip

360°Flip Button

180 ° Flip to Left

180 ° Flip to Right

Prerequisite: Position the drone in such a way that its front is your front (see Pic 1).

Tip:

Do not change the orientation of the transmitter (see Pic 2) after entering headless mode.

Drones generally have a front and rear indicated by LED lights or colored blades. By default,

the users are required to tell the front and the rear of the drone when ying. Under headless

mode, the users can operate the drone without worrying about the orientation.

Headless mode is designed for beginners and users who y the drone in daylight or at a far

distance.

When the drone in Headless Mode, push the Right Stick to forward/backward/left/right, and

the drone will y to forward/backward/left/right accordingly. All direction is the drone front.

Headless Mode

Pic 2

Return Home

* The return home function is only available when the drone is in headless mode.

Press Return Home buttom, the drone will y back to the users.

Prerequisite:

* Make sure the drone is in front of the users (see Pic 1). Wrong position may cause

the drone y to other direction (see Pic 2).

Press Return Home buttom

, the drone will y back to the users. Pull down the throttle stick

slowly to land the drone when the drone y back and close to the user.

Pic 1

Front

Left Right

Rear

Front

Left Right

Rear

Pic 1 Pic 2

Front

Rear

Left Right

Front

Rear

Left Right

To turn on headless mode, press the headless mode button

and the drone LED lights ashes, which indicates the headless

mode is ready.

To turn o headless mode,

press the headless mode button

again and the drone LED lights turns solid, which indicates the

headless mode is o.

Blade Guard Installation Diagram

1. Pull out the motor plug from the moter holder port. Force apart the motor buckle around

the motor (see Pic 1) to take out the motor.

2. Put the new motor back to the original position in the drone and install it into the motor

buckle (see Pic 2). Then connect the motor plug with the motor holder port. (red motor

plug paired with red motor holder port, white motor plug paired with white motor holder

port.)

Note: After installing the new motor, recheck the motor wire and make sure it doesn’t stuck

in the motor holder. Or the motor wire may broke for crashing or droping easily.

Motor Installation Diagram

Pull out the motor Install the motor

Pic 1 Pic 2

Blade Installation Diagram

Install the bladePic 2Pull out the bladePic 1

1. Hitch the blade guard into the motor holder. Press the blade guard with moderate force

and press the buckle in the motor holder at the same time (see Pic 1). The blade

guard will go through the buckle and it indicates successful installation.

2. Press the buckle in the motor holder to take out the blade guard from the drone (see Pic 2).

2. Align the blade hole and the motor axis, press the blade to the motor axis. Make sure the

blade is perfect match with the motor axis (see Pic 2).

( A Blade paired with A motor and B Blade paired with B motor ).

1. Pull up the blade and remove it from the motor axis as Pic 1.

( Do not remove the motor with the blade ).

Pic 1 Pic 2 Remove the blade guardrInstall the blade guard

Spare Parts

For convenience, the spare parts are listed for you to choose, which can be purchased from

the local distributor. (The circle number please refer to the exploded view below)

U32-05

A Motor

(Red Plug)

U32-06

B Motor

(White Plug)

U32-07

Battery

U32-01

Drone Housing

U32-02

Blade Guard

U32-03

Blade

U32-04

Drone Frame

U32-08

USB Wire

U32-09

Transmitter

2. Press down the battery buckle and lift up the battery as Pic 1.

1. Power o the drone.

3. Put the battery back to its original position and press the buckle down to the hole in the

drone as Pic 2.

Battery Installation Diagram

Install the batteryPic 2Remove the batteryPic 1

5. Connect the battery plug with the port in the drone as Pic 4 to power on the drone.

4. Pull up the battery wire and thread it into the hole as Pic 3.

Pic 3 Pic 4

No.

Name No. Name No. Name

Blade Guard

2 A Motor (Red Plug)

3 A Blade

4 B Motor (White Plug)

5 B Blade

6 Battery Box

7 Drone Housing

8 Drone Frame

Troubleshooting Guide

The drone

is under-

powered or

can not y.

1. The blade deformed seriously. 1. Replace blade.

2. The drone battery is too low. 2. Recharge the drone battery.

3. Incorrect installation of blade.

3. Install the blade in accordance with the

user manual instruction.

The drone

can not

hover and

tilts to one

side

1. The blade deformed seriously.

1. Replace blade.

2. The drone frame deformed. 2. Replace the drone frame.

3. The gyro did not resetting after violent

crash.

3. Put the drone on the at ground for

about 10s or restart the the drone to

calibrate again.

4. The motor is damaged. 4. Replace motor.

The drone

indicator

light is o

1. The drone battery is too low. 1. Recharge the drone battery.

2. The battery is expired or overdischarge

protection.

2. Buy a new battery from local seller to

replace or recharge the battery.

3. Poor contact.

3. Disconnect the battery and then connect

it with the plug again.

The

transmitter

indicator

light is o

Problem Problem Cause SolutionNo.

1. The transmitter battery is too low. 1. Replace battery.

2. The battery positive pole and negative

pole are in reverse order.

2. Install the battery in accordance with the

user manual.

3. Poor Contact.

3. Clean the dirt between the battery and the

battery alice.

Fail to

pair the

drone with

transmitter

1. Indicator light is o. 1. The same as above 1.2.3.

2. There is interfering signal nearby.

2. Restart the drone and power on the

transmitter.

3. Misoperation.

3. Operate the drone step by step in

accordance with the user manual.

4. The electronic component is damaged

for frequent crash.

4. To buy spare parts from local seller and

replace damaged parts.

Exploded View

Ripmax FREEDOM 3D U32 User manual

Ripmax FREEDOM 3D U32 User manual

Ripmax FREEDOM 3D U32 User manual

Related papers

Other documents