Aero Pure SBF110G5 OR Installation guide

Brand: Aero Pure

Model: SBF110G5 OR

Type: Installation guide

This manual is also suitable for

SBF110G5 S

BATH FAN

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

..............................................................................................................

.......................................................................................

..........................................................................................................

........................................................................

............................................................................................................

...................................................................................................

..................................................................................................................

...........................................

.............................................................

.................................................................................

...................................................................................

...................................................................

......................................................................................................

...............................................................................................................

TABLE OF CONTENTS

UNPACKING

SUPPLIED ACCESSORIES

DESCRIPTION

GENERAL SAFETY INFORMATION

DIMENSIONS

WIRING DIAGRAM

FEATURES

INDICATION (PLUG-IN DEVICES)

INSTALLATION

I (NEW CONSTRUCTION

INSTALLATION

II (RETROFIT

MAINTENANCE (CLEANING)

PRACTICAL GUIDE TO INSTALLATION

SPECIFICATIONS

WARRANTY

Thank you very much for purchasing our bath fan.

Please read the instructions carefully before attempting to install,

operate or service our ventilating fan. Failure to comply

with instructions could result in personal injury or property

damage. Please retain this booklet for future reference.

Model No.

ABF110DHL5 SeriesABF110DHG6 Series ABF110DHL6 Series

ABF110DHG5 Series

UNPACKING

Unpack and carefully remove the unit from carton.

Refer to the supplied accessories list to verify that all parts are present.

SUPPLIED ACCESSORIES

DESCRIPTION

Grille

Wire

Protector

Nut

Suspension

bracket

assembly

Long screw

(ST4X30)

Installation

instructions

These bath fan models are listed by ETL under ETL file No.5011292.

These bath fan models use a Sirocco fan driven by a brushless DC motor.

The motor is designed to have an extended service life with reduced energy consumption.

The grille covering the fan body is a spring-loaded, quick attach type. A damper for preventing air

counterflow is provided.

The suspension bracket assembly can be used for both new and retrofit situation.

The light uses a bright SMD LED.

or oror

ABF110DHG5 ABF110DHG6 ABF110DHL5 ABF110DHL6

Use this unit only in the manner intended by the manufacturer. If you have any questions, contact

the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Installation work and electrical wiring must be done by qualified person(s) in accordance with

all applicable codes and standards, including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacture′s

guideline and safety standards such as those published by the National Fire Protection Associa-

tion (NFPA), and the American Society of Heating, Refrigeration, and air conditioning Engineers

(ASHRAE) and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden

utilities.

Ducted fans must always be vented to the outdoors.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the

application and be connected to a GFCI (Ground Fault Circuit Interrupter)-protected branch circuit.

These models are ETL listed for tub and shower enclosures.

Not to be installed in a ceiling thermally insulated to a value greater than R40. (This is required for

installation in Canada only).

Do not install this ventilating fan where interior room temperature may exceed

104°F (40°C).

To reduce the risk of fire, electric shock, or injury to persons, observe the following:

WARNING:

1.For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2.Not for use in cooking area. (Fig.B)

3.This product must be properly grounded.

CAUTION:

GENERAL SAFETY INFORMATION

Make sure that the electric service supply voltage is AC 120V, 60Hz.

Follow all local electrical and safety codes, as well as the National Electrical

Code (NEC), and the Occupation Safety and Health Act (OSHA).

Always disconnect the power source before working on or near the fan, motor,

light fixture, or junction box.

Protect the power cord from sharp edges, oil, grease, hot surfaces, chemicals

or other objects.

Do not kink the power cord.

Do not install the unit where ducts are configured as shown in Fig.A.

Provide make up air for proper ventilation.

DIMENSIONS

Unit: inches (mm)

Base PCB box

Humidity sensor module

CO sensor module

Night light module

Motion sensor module

LED light

Blade

Grille

Adaptor

Damper

Frame assy

Knockout plate

Junction box

Model: ABF110DHG6 Series, ABF110DHL6 Series

Model: ABF110DHG5 Series, ABF110DHL5 Series

3 7/8 (98)

4 7/8 (123)

5 4/5 (147)

3 4/5 (97)10 2/5 (265)

10 1/4 (260)

12 1/8 (308)

7 1/3 (186)

3/5 (14.5)

13 (330)

①

②

③

⑧

⑦

⑩

①

②

③

⑧

⑦

⑨

⑩

10 1/4 (260)

12 1/8 (308)

3 7/8 (98)

4 7/8 (123)

5 4/5 (147)

3 4/5 (97)

10 2/5 (265)

④

⑥

13 (330)

7 1/3 (186)

⑤

⑪

⑫

3/5 (14.5)

WIRING DIAGRAM

FEATURES

Model: ABF110DHG5 ABF110DHG6

Model: ABF110DHL5 / ABF110DHL6

Motor

Ground

Live

Neutral

Green

Black

White

Yellow-

green

Red

Signal

Power switch

Control switch

Fan body

Junction box

Motor

Ground

Live

Neutral

Green

Black

White

Light Body

Blue

Brown

White

Live (Light)

Live(N. Light)

Neutral

Yellow-

green

Red

Signal

Power switch

Control switch

Fan body Junction box

●CFM-Selection. Choose 50-80-110CFM; default is high speed.

●Multi-Speed- Switch allows fan to run at continuous lower speed to

meet Indoor Air Quality. For example, when Flow-Selection setting is

80CFM, Multi-Speed can be chosen 0, 50, 60, or 70CFM as a

low speed.

●Delay- Switch for time delay setting. Setting range is 0, 5, 10, 20,

30, 45, or 60 minutes.

●Air Trimming- Switch allows fine-tuning of air volume when the

actual airflow is lower than set.

100

Time(min)

80 110

Air Trimming

Air Volume(CFM)

Time delay

Air trimming

Flow-Selection

Multi-Speed

INSTRUCTIONS:

Turn the power on.

When the control switch is turned on, the fan will run continuously at high speed only. The power

must be on before turning the control switch on. The sensors will not work and Time Delay Switch

does not apply to this mode.

When the control switch is turned off, the fan will run at chosen low speed on Multi-Speed switch

continuously, and boost to the high speed when the sensor detects an increase in Relative

Humidity. The fan will run at high speed for amount of time selected from the Time Delay Switch

before returning to lower speed when the Relative Humidity falls below the set point.

PLUG-IN DEVICES

Humidity Sensor Module- Included in this Aero Pure fan. Insert module

into USB interface. The fan automatically turns on or boosts to a higher

speed when the Relative Humidity (RH) exceeds the user-adjustable

set-point. The fan automatically runs in a lower speed after a period of

time delay or stops running when the Relative Humidity falls below the

set-point.

Humidity detection value setting range: 30% - 80%

CO2 Sensor Module- Insert module into USB interface. The module

begins to detect environmental CO2 concentration when fan is on for

2 minutes, then the fan starts to run or boosts to high speed when

concentration level is over 1000PPM. The fan runs in low speed after

a period of time delay or stops working when concentration level

is less than 800PPM.

Humidity(RH%)

INSTALLATION PLUG-IN DEVICES

Humidity Sensor Module is included with this fan.

Contact Aero Pure to purchase CO2 Sensor Module.

Position A is for CO2 Sensor module, position B is for Humidity Sensor module.

1. Fix to the specified devices to the slot, till hear the sound installed in place.

2. Access USB interface, insert the connector of module into USB receptacle.

USB receptacle

Notes:

Suitable for use with solid-state speed controls.

Solid-state speed controls may cause harmonic

distortion which can cause motor humming noise.

INSTALLATION I (NEW CONSTRUCTION)

Fig.2.a

Fig.2.b

IMPORTANT:

Remove the tape from damper and adaptor

before installation. As shown below:

Fig.1

Two cases of spacing L :

Joist situation:

12 inches (305 mm)

16~24 inches (406~610 mm)

If the spacing L is 16~24 inches (406~610 mm),

use the suspension bracket assembly.

If the spacing L is 12 inches (305 mm) on joists,

please follow the installation step as (Fig.1).

Secure 4 screws (ST4X30) at flange of frame to the

joists. Then follow steps 6 to 9 of Installation

(page 6-8) to complete the installation.

Please wear gloves during the installation work.

CAUTION:

11 4/5~22 1/2 (300~579)

！

4 Screws

(ST4x30)

Tap

INSTALLATION I(NEW CONSTRUCTION)CONTINUED

Fix one side of the bracket assembly to the joists by

drilling 2 tapping screws (ST4x20) which have been

fixed on it. Fig.3

Adjust the length of bracket assembly as the

spacing between joists, and install to joist by drilling

the other 2 tapping screws which have been fixed

on the other side. Adjust the active part of bracket

assembly to the proper position. (Fig.3

Fig.3

Joist

Screws

(ST4X20)

Place the adaptor on the bracket assembly as

indicated position, and install it by using 2

self-drilling screws (ST4X30). (Fig.4)

Unit: inches (mm)

Bend down 8 tabs for positioning as (Fig.2.a) and

unfold the bracket assembly as (Fig.2.b).

Active part

Fig.4

2 Screws

(ST4X30)

Position

of adaptor

Fig.5

Push the fan body upwards until the fan body is

stopped by the buckle on the adapter and secure

the fan body by using the remaining 3 self-drilling

screws (ST4X30). (Fig.5)

Hold the fan body to prevent falling before fixing

the screws.

CAUTION:

！

Buckle

Fan body

3 Screws

(ST4x30)

Install a circular duct and secure it with clamps

or ties and seal it with mastic or approved duct tape.

A 4”, 5”, or 6” circular duct is needed to connect

to relevant part of adaptor. (Fig.6)

Fig.6

Circular duct

Duct tape

INSTALLATION I(NEW CONSTRUCTION)CONTINUED

Remove the knock-out plate and secure conduit

or wire protector nut to knock-out hole. (Fig.7.

Refer to wiring diagram on page 5.

Using UL approved wire nuts, connect house power

wires to the ventilating fan wires (Fig.7.

II), then

attach it to fan body.

Follow all the local electrical safety codes as well

as the National Electrical Code (NEC).

IMPORTANT:

Fig.7

Fig.8

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

outside of Housing and may be

oriented as desired.

Connect

wires

III

Screw from

Parts Bag

Black

Red

Green

Wire nuts

White

Nuts

8.Finish ceiling work. Align ceiling hole with the inside

edges of the flange. (Fig.8)

Unit:inches(mm)

After finishing the ceiling work, fill gap between

flange and ceiling with caulk or other sealant to

prevent air leakage.

Caulk

IMPORTANT:

Ceiling

10 2/5 (265)

Mount grille carefully so that lead wire of light

unit is not pinched.

Fig.11

INSTALLATION I (NEW CONSTRUCTION) CONTINUED

9.Insert mounting springs into slots and mount grille

to fan bodyFig.9

Insert the grille mounting spring on the wiring side

into the slot. (Fig.10)

Insert the plug connector into the housing of the

lighting unit and insert the other mounting spring

into the slot as shown and mount grille to fan body.

(Fig.10, Fig.11)

10.For grille with a light, refer to the following

installation method.

Fig.10

Before turning on the light, make sure the

connector is at the correct position. If not,

the lighting will not work.

The claw of connector must be secured to

the rib completely. (Fig.10)

CAUTION:

！

CAUTION:

！

Grille

Ceiling

Slot

Mounting spring

Fig.9

INSTALLATION I(NEW CONSTRUCTION)CONTINUED

Insert the grille mounting spring on the wiring side

into the slot.

Insert the USB connector into the USB receptacle

and insert other mounting spring into the slot as

shown and mount grille to fan body.

(Fig.12)

11.For grille with a modulerefer to the following

installation method.

Fig.12

1.Put the folded bracket assembly into ceiling hole,

then follow step 3-4 of Installation I (NEW

CONSTRUCTION page 8) to complete the bracket

installation. (Fig.13)

Unit: inches (mm)

Fig.13

Screws

(ST4x20)

10 3/5(270)

INSTALLATION II(RETROFIT)

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

outside of Housing and may be

oriented as desired.

Connect

wires

III

Black

Red

Green

Wire nuts

White

INSTALLATION II (RETROFIT)CONTINUED

Fig.15

Screw from

Parts Bag

Screws

(ST4x30)

Unit:inches (mm)

Fig.14

Follow step 4 of Installation I (NEW

CONSTRUCTION page 8) to complete the

adaptor installation. (Fig.14)

Install a circular duct and secure with clamps

or ties and seal with mastic or approved foil tape.

A 4”, 5”, or 6”

circular duct is needed to connect

to relevant part of adaptor. (Fig.14)

Remove the knock-out plate and secure conduit

or wire protector nut to knock-out hole. (Fig.15)

Refer to wiring diagram on page 5.

Using UL approved wire nuts, connect house power

wires to the ventilating fan wires (Fig.15), then fix

it to fan body

Follow all the local electrical safety codes as well

as the National Electrical Code (NEC).

IMPORTANT:

Fig.16

Follow step 9 of Installation

I (NEW

CONSTRUCTION page 10) to complete the

installation.

Push the fan body upwards until the fan body is

secure with the joint, and secure them by using the

remaining 3 self-drilling screws (ST4X30) (Fig.16)

3 Screws

(ST4x30)

Nuts

MAINTENANCE (CLEANING)

Disconnect power source before working on unit.

Routine maintenance must be done every year.

WARNING:

Fig.17

Fig.18

Clean grille. (Don’t put into hot water. Use

non-abrasive kitchen detergent, wipe dry with

clean cloth). (Fig.18)

The grille should be dry after cleaning before

reattaching to fan motor.

CAUTION:

Never use gasoline, benzene, thinner or any

other such chemicals for cleaning the ventilating

fan.

Do not immerse motor in water when cleaning.

Do not soak resin parts in water over 140°F

(60°C).

Remove grille. (Squeeze mounting spring and

pull down carefully). (Fig.17)

Grille

6. Reinstall grille.

Fig.20

Remove dust and dirt from fan body using a

vacuum cleaner. (Fig.19)

Using a cloth dampened with kitchen detergent,

remove any dirt from fan body. Wipe dry with

clean cloth. (Fig.20)

Fig.19

lnsulation

Fig.21

Properly insulate the area around the

fan to minimize building heat loss and

gain. (Fig.21)

Loose fill or batt insulation can be

placed directly over the fan housing in

the attic.

The fans and fan/light combination units

do not create excessive heat that is a

common problem with recessed light

fixtures or some competitors′ fan/light

combinations. Our efficient, cool-running

motors,

and LED lighting unit do not

create enough ambient heat to be subjected to these limitations.

PRACTICAL GUIDE TO INSTALLATION

Foil tape tightly covers all metal

duct joints (glue PVC joints)

4 inches or 6 inches roof jack, wall cap,

or soffit vent with backdraft damper

Mechanically connect duct to termination

and seal with mastic or approved foil

faced tape

2-3 ft straight run before elbow

ln attic installation,

caulk box to drywall

Short piece of flexible duct helps

alignment and absorbs sound.

Clamps plus mastic or approved

foil faced tape at all flex joints

The ducting from this fan to the outside of the building has a strong effect on the air flow, noise, and energy

use of the fan. Using the shortest, straightest duct routing possible for best performance, and avoid

installing the fan with smaller ducts than recommended. Insulation around the ducts may reduce energy

loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated air flow.

SPECIFICATIONS

Fan light N.light

＜0.3

6 901 50

＜0.3

6.8 936 60

0.3 7.8 954 70

0.4 8.8 987 80

0.6 11 1037 90

0.8 12.8 1079 100

1.0 16 1159 110

＜0.3

5.8 10 0.7 871 50

＜0.3

6.7 10 0.7 888 60

＜0.3

7.7 10 0.7 922 70

0.3 8.8 10 0.7 945 80

0.5 10.8 10 0.7 1000 90

0.7 12.6 10 0.7 1044 100

0.9 15.2 10 0.7 1095 110

Power consumption

(W)

Speed

(rpm)

Air volume

at 0.1'' WG

(CFM)

Model No. Air direction

Voltage

(V)

Frequency

(Hz)

Duct

diameter

(inches)

Noise

(Sones)

Exhaust 120 60 4”, 5”, 6”

ABF110DHL5W

ABF110DHL6W

Exhaust 120 60 4”, 5”, 6”

ABF110DHG5W

ABF110DHG6W

This warranty covers all defects in workmanship or materials for:

The mechanical and electrical parts contained in this product for a period of 72 months from the date of

purchase. You must keep and be able to provide your original sales receipt as proof of date of purchase.

This warranty is covered to the original retail purchaser of this product only. The manufacturer will replace

any mechanical or electrical part that proves defective in normal household use for a period of 72 months.

THIS WARRANTY DOES NOT COVER:

• Damages from improper installation.

• Damages from shipping.

• Damages from misuse, abuse, accident, alteration, lack of proper care and maintenance.

• Damages from service by persons other than a licensed electrician.

• Does not cover any labor or transportation charges related to the repair of this product.

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE.

The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty

does not cover incidental or consequential damages. Some states do not allow the exclusion of incidental

or consequential damages, so this limitation may not apply to you.

Some states do not allow limitations on how long an implied warranty lasts, so this limitation may not apply

to you. This warranty gives you specific legal rights; you may also have other rights, which vary from state

to state.

Aero Pure LLC

1006 Bankton Circle Building B

Hanahan, SC 29410

Tel: 843.377.8642

Fax: 843.377.8643

WARRANTY

WEBSITE: WWW.AEROPUREFANS.COM

Aero Pure SBF110G5 OR Installation guide

Brand: Aero Pure

Model: SBF110G5 OR

Type: Installation guide

This manual is also suitable for

SBF110G5 S

Download PDF

report

Aero Pure SBF110G5 OR Installation guide

This manual is also suitable for

Aero Pure SBF110G5 OR Installation guide

Related papers

Other documents