© Öhlins Racing AB. All rights reserved.
Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB
is prohibited. Printed in Sweden.
Mounting instruction KT893_1 Issued 080305
These instructions and other documents
can be downloaded from
www.ohlins.com
Mounting Instruction
Read the Öhlins Owner’s Manual before installing this product
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
I
n
s
t
a
l
l
i
n
g
a
s
h
o
c
k
a
b
s
o
r
b
e
r
t
h
a
t
i
s
n
o
t
a
p
p
r
o
v
e
d
b
y
t
h
e
v
e
h
i
c
l
e
m
a
n
u
f
a
c
t
u
r
e
r
m
a
y
a
f
f
e
c
t
t
h
e
s
t
a
b
i
l
i
t
y
o
f
y
o
u
r
v
e
h
i
c
l
e
.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00 Fax +46 8 590 025 80
www.ohlins.com
with set-up data
Spring preload
Loosen the screw of the spring platform
clamp. Use the C-spanner provided in this
kit, turn the spring platform to the desired
position. Or, when installed on the vehicle,
turn the spring. Tighten the screw of the
spring platform clamp.
Compression damping
Adjust by turning the screw in the middle of
the golden knob on top of the reservoir.
Use a screwdriver and turn the screw
clockwise to increase damping, turn counter
clockwise to decrease damping.
Rebound damping
Adjust by turning the screw in the middle of
the black knob on top of the reservoir.
Use a screwdriver and turn the screw
clockwise to increase damping, turn counter
clockwise to decrease damping.
CSC Adjuster
Use a screwdriver and turn the screw
clockwise to increase damping, turn counter
clockwise to decrease damping.
Adjuster settings:
The adjusters have a normal right hand thread.
Turn the damping adjusters clockwise to fully
closed (position zero [0]). Then, turn counter
clockwise to open, and count the clicks until you
reach the recommended number of clicks.
See Set-up data.
Rebound damping
(black)
Compression damping
(gold)
ADJUSTMENTS
Set-up data
Spring preload 3 turns (6 mm)
Rebound damping 12 clicks
Compression damping 12 clicks
CSC damping 18 clicks
Free sag and Ride height
Free sag, rear 30±5 mm
Free sag, front 30±5 mm
Ride height, rear 110-115 mm
Ride height, front 80±5 mm
Shock absorber data
Length 410.5 mm
Stroke 109 mm
1
2
3
1
WARNING!
When delivered, the Öhlins shock absorber is
dialed to the recommended settings for the
specific brand and make of the motorcycle. Before
riding, always ensure that the basic settings made
by Öhlins are intact.
Do not use force, delicate sealing surfaces can be
damaged. Handtighten only!
4
2
3
4
CAUTION!
Kit Contents:
Part no. Pcs.
Shock absorber KT893 1
Spring clip 00629-06 1
C-spanner 00710-02 1
Öhlins Sticker 00197-01 2
Sticker “Memo notes” 01180-01 1
Information sheet 01198-01 1
Owner’s Manual 07253-01 1
Before installing this product, check the
contents of the kit listed below. If anything is
missing, please contact your nearest Öhlins
dealer.
SHOCK ABSORBER KT893
for KTM 250 SX-F 2008
During storage and transportation, especially at
high ambient temperature, some of the oil and
grease used for assembling may leak and stain
the packaging. This is in no way detrimental to
the product, wipe off the excessive oil/grease
with a cloth.
NOTE!
No spring included in this kit. See the Spring
Guide in this folder, or contact an Öhlins
dealer for advice.