RAB Lighting W17-30LY Operating instructions

INSTRUCTIONS

W17 WALL PACK INSTALLATION

RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: [email protected]

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required

for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR

WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING:

• Make certain power is OFF before installing or maintaining xture.

NOTE:

• No user maintenance or cleaning required.

Fixture should not be recessed, surface mount only.

1. Open Reector Door by loosening Reector Door Screw (1),

see Fig. 1.

2. Reector Dooreector Door will hinge downward and remain attached will hinge downward and remain attached

during installation as shown in during installation as shown in Fig 2Fig 2..

3. 3. Line up the Line up the Fixture Fixture to desired location. Use the to desired location. Use the Drill Template Drill Template

(Fig. 2)(Fig. 2) on the inside back surface of the on the inside back surface of the FixtureFixture to match to match

most standard junction boxes. most standard junction boxes. Secure the Secure the FixtureFixture in place with in place with

screws screws (supplied by others)(supplied by others)..

4. 4. Complete the wiring to the supply wires and ground Complete the wiring to the supply wires and ground (see wiring (see wiring

instructionsinstructions Fig. 3 Fig. 3))..

5. 5. Pivot the Pivot the ReectorReector DoorDoor back into place and push until it snaps back into place and push until it snaps

closed. Tighten closed. Tighten Reector Door ScrewReector Door Screw (1) to secure (1) to secure Reector

Door to Fixture.

6. Apply weatherproof silicone sealant around the edge of the wall

box. This is especially important with an uneven wall surface.

MOUNTING FIXTURE TO THE WALL

W1730L /36L W1755L/75L/90L W17150L

FIG. 1

FIG. 2

Fixture

Drill Plate

Reector

Door

Reector Door

Screw

Reector

Mounting Screws (4)

(supplied by others)

INSTRUCTIONS

W17 WALL PACK INSTALLATION

RAB Lighting is committed to creating high-quality, aordable, well-designed and energy-ecient LED lighting and controls that make it easy for electricians to install

and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: mark[email protected]

TROUBLESHOOTING

CLEANING & MAINTENANCE

1. Check that the line voltage at the xture is correct. Refer to

wiring directions.

2. Be sure the xture is grounded properly.

3. Is the photocell, if used, functioning properly?

CAUTION: Be sure xture temperature is cool enough to touch.

Do not clean or maintain while xture is energized.

1. Clean tempered glass lensglass lens with non-abrasive, glass cleaning

solution.

2. Do not open xture to clean the LEDs. Do not touch the LEDs.

3. No user maintenance or cleaning required.

ONOFF WIRING

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

FIG. 3

Universal voltage driver permits operation at 120V thru 277V, 50 or

60 Hz, follow the wiring directions below.

1. Connect the black xture lead to the LINE supply lead.

2. Connect the white xture lead to the COMMON supply lead.

3. Connect the GROUND wire from xture to supply ground.

DIMENSIONAL DRAWINGS

W17-IN-0720

RAB WARRANTY: RAB’S warranty is subject to all terms and conditions found at rablighting.com/warranty.

73695-RAB

Easy Answers

rablighting.com