Acclaim Lighting AL-DIMMER-1 HP User Instructions

Acclaim Lighting
Brand
Acclaim Lighting
Model
AL-DIMMER-1 HP
Category
Stroboscopes & disco lights
Type
User Instructions
DESCRIPTIONS
Congratulations with your purchase of this product.
Check for transport damage.
You should be in possession of the following items:
1 AL-DIMMER-1 HP
1 Manual
1 Screwdriver
Should you discover transport damage after unpacking the equipment,
inform the hauler immediately. Never connect a damaged device. You
may also contact your supplier.
DELIVERY PACKET
TECHNICAL SPECIFICATIONS
Operation temperature
Housing
Control Protocol
Listing
Dimensions
Weight
0 degC to +40 degC
Black plastic
DMX-512 (1990)
CE certified
115(L) x 54(W) x 23(H)mm
150g
Analog In/THRU
2-pin terminal
OPERATION GUIDE
User Instructions
Connection
Terminal
Read this manual carefully before using our AL-DIMMER-1 HP. This unit serves as a single channel dimmer. It is
designed to set the intensity for the high power R.G.B. LEDs, features the user may select the current output as
350mA, 500mA or 700mA. Its working mode is available in DMX control and Manual Dim mode, and the analog
signal is available in 0~10V and 1~10V, it's working mode and the DMX address can be set by Dip-switch.
AL-DIMMER-1 HP
-1-
IP 20
Ingress Protection Rating
Power Requirement
12~24VDC
Loading Output
2-pin terminal
DC In
4-pin terminal
Make sure the output current matches the power requirements of the LED fixtures prior to use AL-DIMMER-1 HP.
1.Output Current Option
Output Current 350mA,500mA or 700mA for option
DMX In/Out
3-pin terminal
Made in P.R.C.
GND
Data-
Data+
+12-24V
+12-24V
GND
GND
DC IN
DMX IN
DMX OUT
GND
Data -
Data+
OUTPUT
DMX Address Setting
RoHS
Addr
1
2
4
8
16
32
64
128
256
1 2
3
4
5
6
7
8 9 10
Dim
1
2
4
8
16
32
64
128
CURVE
11 12
1-10V0-10V
DMXMAN
THRU IN
GND
0-10V/1-10V
GND
0-10V/1-10V
350mA
500mA 700mA
AL-DIMMER-1 HP
AL-DIMMER-1 HP
The output current defaults as 350mA and a built-in Dipswitch allows the user to select the output current
as 350mA,500mA or 700mA.
The following contents instruct to how to make the selection for the output current.
-2-
1. Take out the AL-DIMMER-1 HP and the screw driver from packing.
2. Use the screw driver to prize up the rear panel of AL-DIMMER-1 HP with the proper strength, as the following
figures.
3. Use the screw driver to move the 2 way dip-switch to on or off for output current option.
4. After the current was selected, to reassemble the rear panel.
2 way dip-switch
ON
OFF
1 2
After the reassembly is completed, to connect the AL-DIMMER-1 HP to the power source for use.
Reassembly
Current
350mA
500mA
500mA
700mA
Off
2
Off
1
Off On
On Off
On On
While the one of the built-in Dipswitch is "On", the AL-DIMMER-1 HP 500mA current, the one of the current
indicator on the front panel will light, the other black out.
will output
While both the built-in Dipswitch are "Off", the AL-DIMMER-1 HP will output 350mA current, both the current
indicators on . the front panel will black out
700mA
the front panel will light
While both the built-in Dipswitch are "On", the AL-DIMMER-1 HP will output current, both the current
indicators on .
3.Manual Dim Mode
In this mode, the dip-switch 10 is flipped to the "OFF" position,
Flip the dip-switch 1~8 to set the intensity of LED products,
each dip-switch represents a binary value.
-3-
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve,
for example:
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
2.DMX Control Mode(DMX Addressing)
DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication between
intelligent fixtures. Each Dip Switch represents a binary value.
In this mode, the dip-switch 10 is flipped to the "ON" position, DMX address
can be set and the intensity of LED products is dimmable.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
SWITCHES ON SWITCHES ON
START
CH#
START
CH#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
..
..
..
..
..
ON
OFF
1 =
0=
1 2 3 4 5 6 7 8 9 10
ON
OFF
1 =
0=
511
1,2,3,4,5,6,7,8,9
..
..
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10
ON
OFF
1 =
0=
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
SWITCHES ON SWITCHES ON
Intensity
Value
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
..
..
..
..
..
ON
OFF
1 =
0=
255
1,2,3,4,5,6,7,8
..
..
1 2 3 4 5 6 7 8 9 10
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve,
for example:
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
Intensity
Value
-4-
Rev1.0
24-004-2824-00
*Please Note: Improvements and specifications in the design of the unit and the manual are subject to
change without any prior written notice.
4.Analog Input Mode
Flipping the dip-switch 11 to "off" position, the analog input is 0-10V and the intensity of LED product can be
set in 0~100%.When the DMX signal/Manual Dim intensity and 0~10V signal are present, the higher
intensity value will take precedence and override the other one.
Flipping the dip-switch 11 to "on" position, the analog input is 1-10V and the intensity of LED product can be
set in 0~100%. When the DMX signal/Manual Dim intensity and 1-10V analog signal are present, the higher
intensity value will take precedence and override the other one.
With dip-switch 12 in "off" position, the 1-10V analog signal can set the minimum intensity of LED product to 0.
With dip-switch 12 in "on" position, the 1-10V analog signal can set the minimum intensity to 1.
analog
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Acclaim Lighting AL-DIMMER-1 HP User Instructions

Acclaim Lighting
Brand
Acclaim Lighting
Model
AL-DIMMER-1 HP
Category
Stroboscopes & disco lights
Type
User Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents