Acclaim Lighting AL-DIMMER-3F HP User Instructions

Acclaim Lighting
Brand
Acclaim Lighting
Model
AL-DIMMER-3F HP
Category
Security device components
Type
User Instructions
DESCRIPTIONS
Congratulations with your purchase of this product.
Check for transport damage.
You should be in possession of the following items:
1 AL-DIMMER-3F HP
1 Manual
1 Screwdriver
1 External Infrared Remote EYE sensor
1 LED remote controller
Should you discover transport damage after unpacking the equipment,
inform the hauler immediately. Never connect a damaged device. You
may also contact your supplier.
DELIVERY PACKET
TECHNICAL SPECIFICATIONS
Operation temperature
Housing
Control Protocol
Listing
Dimensions
Weight
0 degC to +40 degC
Black plastic
DMX-512 (1990)
CE certified
115(L) x 54(W) x 23(H)mm
150g
DMX In/Out
3-pin terminal
User Instructions
Connection
Terminal
Read this manual carefully before using our AL-DIMMER-3F HP. The AL-DIMMER-3F HP, a multifunction LED
dimmer with 3 channels, is designed to set the intensity for the high power RGB LEDs.
AL-DIMMER-3F HP
-1-
IP 20
Ingress Protection Rating
Power Requirement
12~24VDC, 6.5A Max.
IR In
External Infrared Remote sensor port
Loading Out
6-pin terminal
DC In
4-pin terminal
12VDC: enables to drive 1~3 LEDs/CH.
24VDC: enables to drive 1~6 LEDs/CH.
Output Current 350mA or 700mA for option
The three faders can separately control the relevant channel value.
The current output is available in 350mA and 700mA for option.
Available in online operation and DMX control for slave control, Auto and Manual mode are for master control.
In online operation mode, the master can drive up to 32pcs slave AL-DIMMER-3F HP.
Working mode and DMX address can be set by Dip-switch.
FEATURES
Infrared remote control.
Loading
6A/CH max., Total 6A max.
AL-DIMMER-3F HPAL-DIMMER-3F HP
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
GND
Data-
Data+
+12-24V
+12-24V
GND
GND
DC IN
Made in P.R.C.
DMX IN
DMX OUT
GND
Data -
Data+
Red Green Blue
DMX Address Setting
Blue-
Blue+
Green+
Red-
Red+
Green-
IR
RoHS
AL-DIMMER-3F HP
350mA
700mA
OUTPUT
(350/700mA)
-2-
The following contents instruct to how to make the selection for the output current as 350mA or 700mA.
1. Take out the AL-DIMMER-3F HP and the screw driver from packing.
2. Use the screw driver to prize up the rear panel of AL-DIMMER-3F HP with the proper stength, as the following
figures.
3. Use the screw driver to move the 2 way dip-switch to on or off for output current option.
4. After the current was selected, to reassemble the rear panel.
2 way dip-switch
2=on
1=on
Output current = 700mA
2=off
1=off
Output current = 350mA
ON
OFF
12
After the reassembly is completed, your AL-DIMMER-3F HP is ready to use.
Reassembly
Make sure the output current matches the power requirements of the LED fixtures prior to use AL-DIMMER-3F HP.
2.Output Current Option
While the built-in Dipswitch is "On",t the AL-DIMMER-3F HP outputs
3 groups current of 700mA .
o link to the power, the LED indicator lights red,
The output current defaults as 350mA
While the built-in Dipswitch is "Off", the AL-DIMMER-3F HP
outputs 3 groups current of 350mA .
and a built-in Dipswitch allows the user to select the output current
as 350mA or 700mA.
to link to the power, the LED indicator is blacked out ,
OPERATION GUIDE
The AL-DIMMER-3F HP features the user may use the 3 faders to separately control the intensity of the 3 channels
(Red, Green & Blue).Also, the outputs intensity of these 3 channels can be controlled by Dipswitch, DMX or infrared
remote controller as well. At this time, the AL-DIMMER-3F HP will take the highest luminance value as the priority
outputs intensity.
1.Luminance
4.Manual Control Mode------Master Mode
In this mode, both the dip-switch 10 and 11 are flipped to the " "
position, Flip the dip-switch 1~3 to set the intensity of Red LEDs,
the dip-switch 4~6 to set the intensity of Green LEDs and the dip-switch
7~9 to set the intensity of Blue LEDs. Please refer to the following table
for the details.
OFF
Red
Green
Blue
Red
(SW1~3)
Green
(SW4~6)
Blue
(SW7~9)
Intensity
0000
10014%
01028%
11043%
00157%
10171%
01186%
111100%
000
100
010
110
001
101
011
111
000
100
010
110
001
101
011
111
DipSwitch Setting
-3-
*Please Note: Improvements and specifications in the design of the unit and the manual are subject to
change without any prior written notice.
A DMX value(address) is set by combining the different dipswitches that will add up to the value you wish to achieve,
for example:
Setting DMX address for 21.
Flip switches1,3,&5 to the
"ON" position
Setting DMX address for 201.
Flip switches1,4,7,& 8 to the
"ON" position
Dipswitches# Value
1=1
3=4
5=16
=21
Dipswitches# Value
1=1
4=8
7=64
8=128
=201
3.DMX Control Mode(DMX Addressing)------Slave Mode
DMX is short for Digital Multiplex. This is a universal binary language used as a form of communication between
intelligent fixtures. Each Dip Switch represents a binary value.
In this mode, the dip-switch 11 is flipped to the " " position, DMX address
can be set and the intensity of LED is controlled. Red effect is controlled by
Ch1, Green effect is controlled by Ch2 and Blue effect is controlled by Ch3.
ON
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
1,2,4
3,4
1,3,4
2,3,4
1,2,3,4
1
2
1,2
3
1,3
2,3
1,2,3
4
1,4
2,4
SWITCHES ON SWITCHES ON
START
CH#
START
CH#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
..
..
..
..
..
..
ON
OFF
1=
0=
12345678910
ON
OFF
1=
0=
511
1,2,3,4,5,6,7,8,9
..
..
11 12
1234 567 891011 12
12345678910
ON
OFF
1=
0=
11 12
In the mode, flip the dip-switch 10 to " " and the dip-switch 11
to the " " position, Flip the dip-switch 1~3 to set the Fade,
dip-switch 4~6 to set the Speed and dip-switch 7~9 to set the
Pattern. Please refer to the following table for the details.
ON
OFF
Fade
Speed
Pattern
12345678910
ON
OFF
1=
0=
11 12
Fadtime
(SW1~3)
Speed
(SW4~6)
Pattern
(SW7~9)
000
100
010
110
001
101
011
111
128s
64s
32s
16s
8s
4s
2s
1s
1
2
3
4
5
6
7
DipSwitch
Setting
0
14%
28%
43%
57%
71%
86%
100%
Auto(Program 1~7
running in a cycle )
5.Auto Mode------Master Mode
6.IR Control (with LED Remote Operation)
4.2.Operation Instructions
4.2.1 Before operation, make sure the batteries(3V, CR2025) have been installed properly.
4.2.2 Operation Instructions
There are 8 dedicated color brightness keys(marked Red, Green, Blue, Cyan, White, Magenta, Yellow, Amber).
The "AUTO" and the "UNIT SETTING" keys, as well as Raise&Lower keys(marked for "raise" and for "lower")
are on the remote unit.
The detailed function will be illustrated in the next table.
5.1
5.1.1 Before connecting, please isolate the main power.
5.1.2 Plug the external connected IR EYE sensor into the external IR connector correctly.
5.1.3 Thus, turn the main power on.
1).Once you've confirmed all work modes and relative parameters, you can remove the external connected IR EYE
sensor.
2).NEVER remove the external connected IR sensor when powering on for preventing from the damage.
.Connecting an external connected IR EYE sensor to the AL-DIMMER-3F HP
Note:
The AL-DIMMER-3F HP is available in being controlled by external connected IR EYE sensor. The IR EYE sensor
should be connected properly before operation.
IR EYE Sensor
LED remote controller
-4-
In online operation, only one master AL-DIMMER-3F HP is allowed in a link. The master controls the slave
AL-DIMMER-3F HP and maximum 32pcs can be controlled.
Note:
NOTE:
Effective distance from IR sensor to LED Remote controller shall be limited within the range of 10m. Otherwise, it
results out of control.
Keys Functions
RED
GREEN
BLUE
CYAN
MAGENTA
YELLOW
WHITE
AMBER
AUTO
UNIT SETTING
PATTERN/RED
PATTERN/RED
SPEED/GREEN
SPEED/GREEN
FADE/BLUE
FADE/BLUE
BRIGHTNESS
BRIGHTNESS
Red, 100% brightness
Green, 100% brightness
Blue, 100% brightness
Cyan, 100% brightness
Magenta, 100% brightness
Yellow, 100% brightness
White, 100% brightness
Amber, 100% brightness
Automatically cycles through colors at100% brightness
All settings were set by dip-switches.
Selects the next pattern or increase the Red brightness.
Holding the key down will gradually increase the brightness to its maximum value.
Selects the previous pattern or decrease the red brightness.
Holding the key down will gradually decrease the brightness to its minimum value.
Increases the Speed value or the Green brightness.
Holding the key down will gradually increase to its maximum value.
Decreases the Speed value or the Green brightness.
Holding the key down will gradually decrease to its minimum value.
Increases the Fadetime or the Blue brightness.
Holding the key down will gradually increase to its maximum value.
Decreases the Fadetime or the Blue brightness.
Holding the key down will gradually decrease to its minimum value.
Increases the master brightness.
Holding the key down will gradually increase the brightness to its maximum value.
Decreases the master brightness.
Holding the key down will gradually decrease the brightness to its minimum value.
ON/OFF
On/off the unit.
-5-
Rev1.0
24-004-3065-00
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Acclaim Lighting AL-DIMMER-3F HP User Instructions

Acclaim Lighting
Brand
Acclaim Lighting
Model
AL-DIMMER-3F HP
Category
Security device components
Type
User Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents