GOODGRIPS Expandable On-The-Wall Organizer Installation guide

Type
Installation guide

GOODGRIPS Expandable On-The-Wall Organizer helps you to organize and store your tools or other items efficiently. It comes with various adjustable components like hooks and grip locks that can be customized to fit different tool sizes and shapes. The organizer also features slide-on end caps to keep your tools securely in place. It's easy to install and can be adjusted to your desired length, making it suitable for various spaces. The organizer is ideal for workshops, garages, or any area where you need to keep your tools organized and accessible.

GOODGRIPS Expandable On-The-Wall Organizer helps you to organize and store your tools or other items efficiently. It comes with various adjustable components like hooks and grip locks that can be customized to fit different tool sizes and shapes. The organizer also features slide-on end caps to keep your tools securely in place. It's easy to install and can be adjusted to your desired length, making it suitable for various spaces. The organizer is ideal for workshops, garages, or any area where you need to keep your tools organized and accessible.

Use a pencil to mark the wall
through the two holes at either
end of the rails. If the third hole
in the middle is visible, mark
that too.
OVER
B Grip Locks x4
C Organizer Rails
E Large Rail
Endcap
F Small Rail
Endcap
1a. To adjust configuration of
the grip locks (B) and hooks (A),
remove cap (E) on the right
side of the organizer rail (C).
1b. Slide grip locks and hooks off.
Note: You can also adjust
configuration after installation
by removing the cap on the right
side and sliding pieces off the
aluminum rail. (Assure you will
have room to do this before
installing.)
Slide grip locks (B) and
hooks (A) back on in desired
order. Reattach the cap (E) to
organizer rail (C).
Adjust the organizer rails (C)
to desired length for your space.
Important Note:
Do not extend
organizer past the
point at which you
can see the red
indicator lines on
rail. If you expose
the
se red lines,
retract rails until lines
are covered again.
Place rails (C) against wall
and place included level (D)
along top of aluminum brackets
to ensure the organizer is
straight.
C
C
1
1
2
D
C
2
1
1b
E
C
A
B
2
1
1a
1b
E
C
A
B
Includes
1a
1b
2
3
4
5
1
C
Place anchors (H) into wall
and push in until flush with
wall. If necessary, use a
hammer or mallet to finish.
Note: : These screws/anchors
are for use on drywall. For
walls of other materials, use the
appropriate screws and tools.
Attach rails (C) to the wall with
screws (G). Gently pull on rails
to ensure security before
adding tools.
Align holes in rails (C) with
holes in wall.
7
6
8
2
H
1
2
1
E
A
B
E
Remove organizer from wall.
Drill pilot holes over the pencil
markings (we recommend a
inch/3 mm drill bit). Drill
out the holes with a larger
drill bit (we recommend a
¼ inch/6 mm drill bit).
1
8
Expandable
On-the-Wall Organizer
Installation Instructions
To use grip locks, simply press
the handle of a tool straight into
the grip lock toward the wall.
The grip lock will adjust to fit the
handle and hold tight until you
simply pull to remove the tool.
C
G
3
G Screws x3*
*for use on drywall only
H Drywall
Anchors x3
A Hooks
x4
D Level
A
B
D
To Use
  • Page 1 1

GOODGRIPS Expandable On-The-Wall Organizer Installation guide

Type
Installation guide

GOODGRIPS Expandable On-The-Wall Organizer helps you to organize and store your tools or other items efficiently. It comes with various adjustable components like hooks and grip locks that can be customized to fit different tool sizes and shapes. The organizer also features slide-on end caps to keep your tools securely in place. It's easy to install and can be adjusted to your desired length, making it suitable for various spaces. The organizer is ideal for workshops, garages, or any area where you need to keep your tools organized and accessible.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI