ABB RELION 650 SERIES Quick start guide

—

RELION® 670 SERIES

670/

650 series IEC

Version 2.2

Quick start guide

Document ID: 1MRK 500 129-UEN

Issued: June 2018

Revision: A

Product version: 2.2

Table of contents

Section 1 Introduction.......................................................................3

Section 2 Safety information............................................................ 5

Symbols on the product......................................................................5

Warnings............................................................................................ 5

Caution signs......................................................................................7

Section 3 Unpacking and inspecting................................................ 9

Removing transport packaging...........................................................9

Inspecting the product........................................................................ 9

Identifying the product................................................................... 9

Checking delivery items.................................................................9

Inspecting the IED......................................................................... 9

Returning an IED damaged in transit............................................ 9

Section 4 IED hardware................................................................. 11

Overview...........................................................................................11

Variants of case size with local HMI display................................11

Case from the front and rear sides.............................................. 13

Section 5 Powering up the IED...................................................... 19

How to know the voltage level.......................................................... 19

How to connect to the power supply.................................................20

Energizing the IED............................................................................21

Section 6 LHMI overview................................................................23

Local HMI......................................................................................... 23

Keypad........................................................................................ 23

Display.........................................................................................27

LEDs............................................................................................30

Local HMI functionality................................................................ 31

Protection and alarm indication.............................................. 31

Section 7 Connecting to the PCM600 software..............................33

PCM600 tool.....................................................................................33

Connectivity packages.................................................................33

Preparing for the connection............................................................ 34

Installing the PCM600 software........................................................34

Connecting the cables...................................................................... 34

Section 8 Editing the network settings........................................... 37

Table of contents

670/650 series 2.2 IEC 1

Quick start guide

Setting up communication between PCM600 and the IED...............38

Section 9 Working with the PCM software..................................... 43

Table of contents

2 670/650 series 2.2 IEC

Quick start guide

Section 1 Introduction

GUID-DCFD62E5-F592-4513-84B0-EC73C7C61838 v1

The Quick Start Guide contains instructions on how to setup the Relion 670/650

series IED to get started. The guide provides instructions to setup with a

preconfigured IED, however, it is also useful for the customized version of the

IED.

The guide describes basic instructions only. For complete information, see the IED

manuals.

GUID-CE76425E-C9C1-404F-8BB3-AD133E903EE7 V3 EN-US

Figure 1: Sample of an IED

1MRK 500 129-UEN A Section 1

Introduction

670/650 series 2.2 IEC 3

Quick start guide

4

Section 2 Safety information

2.1 Symbols on the product

GUID-E48F2EC3-6AB8-4ECF-A77E-F16CE45CA5FD v4

All warnings must be observed.

Read the entire manual before doing installation or any

maintenance work on the product.

Class 1 Laser product. Take adequate measures to protect your eyes

and do not view directly with optical instruments.

Do not touch the unit in operation. The installation shall take into

account the worst case temperature.

2.2 Warnings

IP1504-1 v2

Observe the warnings during all types of work related to the product.

GUID-C9B6638A-57E7-4E05-9A33-A60E359C54AF v1

Only electrically skilled persons with the proper authorization and

knowledge of any safety hazards are allowed to carry out the

electrical installation.

M2366-2 v2

National and local electrical safety regulations must always be

followed. Working in a high voltage environment requires serious

approach to avoid human injuries and damage to equipment.

M2362-2 v1

Do not touch circuitry during operation. Potentially lethal voltages

and currents are present.

1MRK 500 129-UEN A Section 2

Safety information

670/650 series 2.2 IEC 5

Quick start guide

M2364-2 v1

Always use suitable isolated test pins when measuring signals in

open circuitry. Potentially lethal voltages and currents are present.

M2370-2 v1

Never connect or disconnect a wire and/or a connector to or from a

IED during normal operation. Hazardous voltages and currents are

present that may be lethal. Operation may be disrupted and IED and

measuring circuitry may be damaged.

GUID-BEDD698E-356C-4CF9-9DAE-64DB3CEADEAD v1

Dangerous voltages can occur on the connectors, even though the

auxiliary voltage has been disconnected.

M2369-2 v3

Always connect the IED to protective earth, regardless of the

operating conditions. This also applies to special occasions such as

bench testing, demonstrations and off-site configuration. This is

class 1 equipment that shall be earthed.

M2367-2 v1

Never disconnect the secondary connection of current transformer

circuit without short-circuiting the transformer’s secondary

winding. Operating a current transformer with the secondary

winding open will cause a massive potential build-up that may

damage the transformer and may cause injuries to humans.

M2372-2 v1

Never remove any screw from a powered IED or from a IED

connected to powered circuitry. Potentially lethal voltages and

currents are present.

SEMOD168311-3 v1

Take adequate measures to protect the eyes. Never look into the

laser beam.

GUID-11CCF92B-E9E7-409C-84D0-DFDEA1DCBE85 v2

The IED with accessories should be mounted in a cubicle in a

restricted access area within a power station, substation or industrial

or retail environment.

Section 2 1MRK 500 129-UEN A

Safety information

6 670/650 series 2.2 IEC

Quick start guide

2.3 Caution signs

IP1503-1 v1

GUID-5D1412B8-8F9D-4D39-B6D1-60FB35797FD0 v2

Whenever changes are made in the IED, measures should be taken

to avoid inadvertent tripping.

GUID-F2A7BD77-80FB-48F0-AAE5-BE73DE520CC2 v1

The IED contains components which are sensitive to electrostatic

discharge. ESD precautions shall always be observed prior to

touching components.

M2695-2 v2

Always transport PCBs (modules) using certified conductive bags.

M2696-2 v1

Do not connect live wires to the IED. Internal circuitry may be

damaged

M2697-2 v2

Always use a conductive wrist strap connected to protective earth

when replacing modules. Electrostatic discharge (ESD) may

damage the module and IED circuitry.

M2698-2 v2

Take care to avoid electrical shock during installation and

commissioning.

M2693-2 v1

Changing the active setting group will inevitably change the IEDs

operation. Be careful and check regulations before making the

change.

GUID-3BEE51C6-8793-4C89-B8A8-07D0FA6EE4CA v3

Avoid touching the enclosure of the coupling capacitor REX061

unit and the shunt resistor REX062 unit. The surface may be hot

during normal operation. The temperature can rise 50°C in REX061

and 65°C in REX062 above the ambient temperature.

1MRK 500 129-UEN A Section 2

Safety information

670/650 series 2.2 IEC 7

Quick start guide

8

Section 3 Unpacking and inspecting

3.1 Removing transport packaging

AMU0600514 v5

IEDs require careful handling.

1. Examine the delivered products to ensure that they have not been damaged

during the transport.

2. Remove the transport packing carefully without force.

The cardboard packaging material is 100% recyclable.

3.2 Inspecting the product

3.2.1 Identifying the product

AMU0600513 v5

1. Locate the IED's order number from the label attached to the IED's case.

2. Compare the IED's order number with the ordering information to verify that

the received product is correct.

3.2.2 Checking delivery items

GUID-2A6D8F5A-470F-40D1-9EAE-60DE4DD85EE6 v1

Check that all items are included in the delivery in accordance with the delivery

documents.

3.2.3 Inspecting the IED

GUID-F6333353-F05D-4B41-BE44-5CE5274E788E v2

• Check the IED to see if any damage occurred during transportation.

3.2.4 Returning an IED damaged in transit

GUID-966A05ED-CD30-4F66-957E-00FF38943A73 v4

If damage has occurred during transport, appropriate actions must be taken against

the latest carrier. Please inform the nearest ABB office or representative. Notify

1MRK 500 129-UEN A Section 3

Unpacking and inspecting

670/650 series 2.2 IEC 9

Quick start guide

ABB immediately if there are any discrepancies in relation to the delivery

documents.

Section 3 1MRK 500 129-UEN A

Unpacking and inspecting

10 670/650 series 2.2 IEC

Quick start guide

Section 4 IED hardware

4.1 Overview

IP14270-1 v1

4.1.1 Variants of case size with local HMI display

M15024-3 v6

IEC04000458-2-en.psd

IEC04000458 V2 EN-US

Figure 2: 1/2 19” case with local HMI display.

1MRK 500 129-UEN A Section 4

IED hardware

670/650 series 2.2 IEC 11

Quick start guide

IEC05000762-2-en.psd

IEC05000762 V2 EN-US

Figure 3: 3/4 19” case with local HMI display.

IEC04000460-2-en.psd

IEC04000460 V2 EN-US

Figure 4: 1/1 19” case with local HMI display.

Section 4 1MRK 500 129-UEN A

IED hardware

12 670/650 series 2.2 IEC

Quick start guide

4.1.2 Case from the front and rear sides

IP16286-1 v2

M16105-3 v10

Table 1: Designations for 1/2 x 19” casing with 1 TRM slot

1MRK002801-AC-2-670-1.2-PG V.3 EN

1MRK002801-AC-2-670-1.2-PG V4 EN-US

Rear position Module

X11 PSM

X31 and X32 etc. to X51 and X52 BIM, BOM, SOM, IOM or MIM

X301, X302, X303, X304 SFP

X305 LDCM

X306 LDCM or OEM

X3061, X3062 SFP if OEM is selected

X311: A, B, C, D SLM

X312 LDCM, IRIG-B, GTM

X313 LDCM, IRIG-B, GTM, RS485

X401 TRM

1MRK 500 129-UEN A Section 4

IED hardware

670/650 series 2.2 IEC 13

Quick start guide

SEMOD111882-4 v8

Table 2: Designations for 3/4 x 19” casing with 1 TRM slot

1MRK002801-AC-3-670-1.2-PG V4 EN-US

Rear position Module

X11 PSM

X31 and X32 etc. to X101 and X102 BIM, BOM, SOM, IOM or MIM

X301, X302, X303, X304 SFP

X305 LDCM

X306 LDCM

X3061, X3062 SFP if OEM is selected

X311: A, B, C, D SLM

X312 LDCM, IRIG-B, GTM

X313 LDCM, IRIG-B, GTM, RS485

X401 TRM

Section 4 1MRK 500 129-UEN A

IED hardware

14 670/650 series 2.2 IEC

Quick start guide

SEMOD111884-4 v7

Table 3: Designations for 3/4 x 19” casing with 2 TRM slot

1MRK002801-AC-4-670-1.2-PG V.3 EN

1MRK002801-AC-4-670-1.2-PG V4 EN-US

Rear position Module

X11 PSM

X31 and X32 etc. to X71 and X72 BIM, BOM, SOM, IOM or MIM

X301. X302, X303, X304 SFP

X305 LDCM

X306 LDCM

X3061, X3062 SFP if OEM is selected

X311: A, B, C, D SLM

X312 LDCM, IRIG-B, GTM

X313, X322, X323 LDCM, IRIG-B, GTM, RS485

X401 TRM 1

X411 TRM 2

1MRK 500 129-UEN A Section 4

IED hardware

670/650 series 2.2 IEC 15

Quick start guide

M16106-3 v10

Table 4: Designations for 1/1 x 19” casing with 1 TRM slot

1MRK002801-AC-5-670-1.2-PG V.3 EN

1MRK002801-AC-5-670-1.2-PG V4 EN-US

Rear position Module

X11 PSM

X31 and X32 etc. to X161

and X162

BIM, BOM, SOM, IOM or

MIM

X301, X302, X303, X304 SFP

X305 LDCM

X306 LDCM

X3061, X3062 SFP if OEM is selected

X311: A, B, C, D SLM

X312 LDCM, IRIG-B, GTM

X313 LDCM, IRIG-B, GTM,

RS485

X401 TRM

Section 4 1MRK 500 129-UEN A

IED hardware

16 670/650 series 2.2 IEC

Quick start guide

Page is loading ...

ABB RELION 650 SERIES Quick start guide

This manual is also suitable for

ABB RELION 650 SERIES Quick start guide

Related papers

Other documents