INSTRUCTION MANUAL
V1.1
Security Camera
Day/Night
EN
PROFESSIONAL SECURITY MADE EASY
2
Introduction
Congratulations on your purchase of This CCTV
camera from ZOSI.This camera can operate in
almost all lighting conditions, from bright daylight
(provided it’s not pointed straight toward the
sun) to pitch darkness.
The camera is very sensitive to light and
therefore can make use of even the smallest
amount of light to provide an image of what it
sees.In low light,this comes through as a black
and white image.
In complete or near-total darkness, the camera
uses built-in infrared LEDs to illuminate the area
in front of it. This light is invisible to the human
eye, although you might notice a faint red glow
coming from the front of the camera this is normal.
In day or well-lit environments,the IR Cut Filter
feature of the camera activates to lter out wav-
elengths of light the camera does not need in
order to provide a clear color image.
Important note
：All jurisdictions have specic
laws and regulations relating to the use of came-
ras. Before using any camera for any purpose,it
is the buyer’s responsibility to be aware of all
applicable laws and regulations that prohibit or
limit the use of cameras and to comply with the
applicable laws and regulations.
Warning
：Modications not approved by the
party responsible for compliance could void
user’s authority to operate the equipment.
Important safety instructions
1) Make sure product is xed correctly and
stable if fastened in place.
2) Do not operate if wires and terminals are
exposed.
3
Choosing a Location for this Camera
To get optimal results from your camera, where you install is important. You should consider the
distance between the camera and its subject to ensure you obtain a good view of the areas in focus.
Also think about the appropriate mounting places (e.g., under the eaves of a roof is a good choice)
where it won’t be either an easy target for vandals or affected by constant light reections of moving
vehicles (which can result in falsely triggered motion detection). There are a number of factors you
will need to consider when choosing where to mount your camera - not least of which is what you will
want to see.
To mount the camera
Position the camera in the location you want to mount it, and mark the screw holes on the surface
to position the screws. Then, using appropriate screws for the surface you’re xing the camera to,
screw the camera into place.
If you’re mounting to a wooden surface, then screw the camera directly to the surface.
If you’re mounting to a masonry surface (bricks, concrete or similar) then you’ll need to use the
included wall plugs.
4
Mounting the Camera
The camera can be mounted onto a at, vertical surface using screws. The surface must have
sufcient strength to hold the camera. Materials such as hardwood, brick or masonry are good
options, You can mount the camera onto a metal surface, but you’ll need to supply your own
mounting hardware.
Power
Connector
Video
Connector
Infra-red
LEDs
Camera
lens
Please note, model shown is for
illustration purposes only.
Positioning the Cables
1.When running your cable, try to avoid
bending it at sharp angles.
2.Don’t put your cable near live electrical
wiring. AC electricity generates radio
“noise” which can interfere with the
signal from your camera.
3.All wiring and connectors must be
suitably insulated and protected from
moisture and sunlight because they are
not weather resistant.
5
Mounting the Camera
1
1
2
3
23
Rotate the camera by loosening the screw
(using screw driver).
Adjust the elbow joint by loosening the screw.
The neck of the stand attached to the
mounting base, rotate the stand by loosening
the radial joint locking ring.Once in position ,
tighten the ring again.
Model 1
wrench
6
Mounting the Camera
1
2
3
Model 2
wrench
1
2
3
Rotate the camera by loosening the screw
(using screw driver).
Adjust the elbow joint by loosening the screw.
The neck of the stand attached to the
mounting base, rotate the stand by loosening
the radial joint locking ring.Once in position ,
tighten the ring again.
7
Mounting the Camera
1
2
Model 3
wrench
1
2
Adjust to the position you want up or down.
The neck of the stand attached to the
mounting base, rotate the stand by loosening
the radial joint locking ring. Once in position ,
tighten the ring again.
8
Mounting the Camera
123
Model 4
1
2
3
loosen the screw on each side to adjust this
joint ,this enables the camera left or right.
loosen the screw and adjust to the position
you want (up or down).
loosen the screw on each side, to rotate the
camera left or right.
9
Power
Adapter
Positioning the Cables
Please note, model shown is
for illustration purposes only.
For 2 & 4 camera packs:
Connect the extension cable's DC
socket to the multiple sockets on the
power splitter.Then, plug the single
end of the power splitter to the DC
plug on the power adapter.
For a single camera:
Connect the extension cable's
DC socket to the DC plug on the
power adapter.
Video
Connector
Power
Connector
Video &
Power Cable
Power Splitter
Cable
Power
Adapter
2
1
2
1
10
Troubleshooting
Q: Video Loss appears where the image from my camera should be displaying on my DVR?
A:
1.Check the extension cable (power and video) is securely connected to the camera.
2.Check the video output from the camera is securely connected to a video input channel on the DVR.
3.Check the power from the camera is securely connected to a power supply
.
Q: When I view an image from the camera at night I only see a bright spot and no image?
A:
A reection can be caused in night vision mode if the camera is looking through a window. At night, the
infrared light the camera uses to see in the dark can ‘bounce back’ off a reective surface (such as
glass, water, spider webs, some ceramics and so on) and effectively blind the camera. If you want to see
outside, mount the camera outside - we made it weatherproof for a reason!
Q: The BNC extension cable will not connect to my TV?
A
: Many TV’s and monitors do not have a BNC connector but do have an RCA connector. Connect a BNC
to RCA adapter to the end of the extension cable and then plug into the RCA video input on your TV or
monitor.
11
Limited Warranty Terms & Conditions
ZOSI Communications warrants this product against defects in workmanship and material for a
period of one year from its original purchase date. You must present your receipt as proof of date
of purchase for warranty validation. Any unit which proves defective during the stated period will be
repaired without charge for parts or labour or replaced at the sole discretion of ZOSI. The end user
is responsible for all freight charges incurred to send the product to ZOSI’s repair centres. The end
user is responsible for all shipping costs incurred when shipping from and to any country other than
the country of origin.
The warranty does not cover any incidental, accidental or consequential damages arising from
the use of or the inability to use this product. Any costs associated with the tting or removal of
this product by a tradesman or other person or any other costs associated with its use are the
responsibility of the end user. This warranty applies to the original purchaser of the product only
and is not transferable to any third party. Unauthorized end user or third party modications to any
component or evidence of misuse or abuse of the device will render all warranties void.
By law some countries do not allow limitations on certain exclusions in this warranty. Where
applicable by local laws, regulations and legal rights will take precedence.
www.zositech.com
All rights reserved. No part of this publication may be reproduced by any means without written permission from ZOSI. The information
in this publication is believed to be accurate in all respects.
ZOSI cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to
change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
PACKAGING
PROFESSIONAL SECURITY MADE EASY
1. Download APP
Esee application for android,eseenet for iphone
Esee APP is in the file, you can directly install in your phone.
Eseenet APP you can follow the PDF file “Iphone APP-manual”
2. How to get the device ID
Input camera’s IP address in IE’s address bar, and user name
is :admin, there is no password, you can login directly. If there is
no image, please follow the guide to install the activeX. Then you
can view the picture.
If it shows in the picture, you can directly get it.
If it doesn’t display, Click setup-OSD setup- Enabled
DeviceIDOverlay, Then you can see the ID.
Type the device ID when you setup the phone view.
Instruction for Iphone
Step 1 : Go to APP store
Step 2: Search Eseenet
Step 2: Input APP ID
password
Step 4 : Click down
Step 1: Log in
Eseenet application,
click “+” Icon
Step 2: Enter device
edit page
Step 3: Input DVR log
in information
Step 4: Added
successfully.it will
show below page
Step 5: Click channel
No. to get video
Step 1:It will connect
channel 1 video by
default, click “+” to
add more channel
Step 2: Click this icon
to edit DVR log
inInformation
Step 3: Add device
group
Step 4: Play/Pause
Snapshot/Record
Step 5: File
management and
more settings
1 Iphone application download and installation
2 Esee mobile application(Eseenet) add device
11 Esee mobile application(Eseenet) function introduction
IE view
Input camera’s IP address in IE’s address bar, and user name
is :admin, there is no password, you can login directly. If there is no
image, please follow the guide to install the activeX. Then you can
view the picture.
How to change IPC camera IP address
1. Please install the software “IPCamSuite” on
your PC.
2. Make sure the IPC camera connected your
router and the power supply, open IPCamSuite,
the software will search the IPC camera
automatically.
3. And then type the new IP address for your IPC
camera in the “ Refresh” windows.
e.g. :192.168.0.XXX, the same segment as your
router. And the Netmask and the Gateway.
4. Then tap Apply, the IP address will refresh.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
EWETON -HDCam-A6546 User guide
-
Comelit IPNVR006A Quick Manual
-
-
Comelit AHDVR042 Series Quick Manual
-
-
-
-
-
COSOOS W02 User guide
-
