Fraser Hill Farm FSWL016RDA-RD User manual

Brand
Fraser Hill Farm
Model
FSWL016RDA-RD
Type
User manual
1) Schematic diagram
2) List of Components
No.
Name
Quantity
1
L-shape support
1
2
hold-nut
1
3
lamp
1
4
U-shaped fastener
1
5
built-in wire
1
6
power wire
1 (137in)
7
adapter (12V AC 500mA)
1
8
extended wire
1 (137in)
9
iron nail, screw and expansion tube
7
Note
1, 2,3,4,5,6,7,8 are wire connectors.
3) Assembly process
1. Determine installation site
It is suggested to install at the height of 71in from the
ground to get the best view angle;
The installation must allow for the power wire to run
into the house through gaps of windows or doors to
avoid the adapter and main power supply to be
dampened and cause danger.
2. Install L-shaped support
Method A: See above figure to apply the lamp with
only one iron nail (if you’re not able to use an iron nail
due to the wall materials, use the screw expansion
tube instead). The advantage of this method is that it
can reduce damages on the wall surface If there has
been an iron nail (or a screw) on the wall already, it
only needs to adjust the length slightly. The
disadvantage of this method is that the lamp may be
swayed by the external force and is not very sturdy.
Therefore, this method is appropriate for the places
where it cannot be influenced by the strong wind or
human touch. The specific method is: to fix the
supplied iron nail (or screw + expansion tube) on the
wall surface which shall be 2-3mm away from the cap
of the iron nail (or screw) so that the lamp can be
suspended on it as shown in the following figure.
Then use two screws to fix U-shaped fastener (4) into
L-shaped support (1):
Connect the plug (4) of power wire (6) with the socket
(3) of built-in wire (5) and then suspend L-shaped
support (1) on the wall.
Method B: if the lamp holder is easy to be effected by
Caution
This product (especially the lamp holder) is
fragile, do not exert too much strength or drop it
during the assembly and use. Be sure to fix it on
the wall securely.
Please assemble it in strict accordance with
the steps and requirements specified in the
instruction to ensure safety and reliability
during the installation.
wind or human activities, it will need to be fastened. It is
suggested to use Method B to install L-shaped support
(1). The specific method is: drill two circular holes with
diameter of X mm and depth Y mm, and use two
expansion tubes and grub screws to fix U-shaped
fastener (4) on the wall, then use two screws to fix
L-shaped support (1) on the U-shaped fastener. But
before doing this, do not forget to connect plug (4) with
socket (3) as shown in the above figure:
3. Fix the lamp
a. Connect power wire to the lamp: After ensuring the
L-shaped support is well suspended on the wall, insert the
plug (2) of the built-in wire into the socket (1) on the top of
the lamp (3):
b. Fix lamp: lift the lamp (3) up so that the upper part of the
plug (2) and its wire can enter into the hole of the hold-nut
(2), and turn the hold-nut (2) to let it tightly fit the thread of
the upper part of the lamp until the lamp and L-shaped
support to be fixed as a whole. Meanwhile, adjust the
direction of the lamp until it is satisfied. Note: #1. The
hold-nut must be screwed tightly. #2. The lamp holder is
fragile, use caution so it doesn’t fall on ground.
4. Power on and examination
a．Power on: connect the plug (5) of power wire (6) with
the socket (8) of adaptor (7). If the power wire (6) is not long
enough, add extended wire (8) between those two and
connect (5) and (6), (7) and (8) separately. After that,
connect the adapter (7) with main power supply.
b. Examination: there is a switch at the bottom of the lamp
(3) (see the following figure). Turn on the switch to left side;
the lights should be twinkling, snow flying around and
music playing. If the above are not functioning, check that
the connections are done properly. You can also turn the
switch to right side to turn off the music.
5. Attention
Please pay special attention:
a. Please fix the hold-nut at the top of lamp securely.
b. All connection points 1, 2, 3, 4, 5, 6, 7 and 8 must be
screwed securely to avoid water and electricity leakage!
c. It is best to ensure that the connecting point between
adapter and main power should be located indoors
where it’s free from rain and snow, to avoid the electricity
leakage or electric shock risk.
  • Page 1 1
  • Page 2 2

Fraser Hill Farm FSWL016RDA-RD User manual

Brand
Fraser Hill Farm
Model
FSWL016RDA-RD
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents