Dante DLM1985 Operating instructions

1

DLM1971-DLM1985

PTZ Domes

Installation and Operations Manual

Model Number: DLM1971-DLM1985

Description: PTZ Domes, Color 18x, D/N 23x 26x,

27x, 30x, 35x and 36x

2

Catalog

Chapter 1：

：：

：Installation manual

………………………………………… ……………………………3

1.Preface………………………………………………………………………………………………… 3

2.Safeguards and warnings………………………………………………………………… …………3

3.Special attention.........................................…………………………………….………………….3

4.Structure of high speed dome camera....................................................................................6

5.Main function features………………………………………………………………………………..6

6.Installation of the speed dome camera……………………………………………………………7

7.Specification………………………………………………………………………………………...…8

Chapter 2 Operation………………………………………………………………………………… ...… 12

1.Basic operation explanation……………………………………………………………….….. ……12

2.PTZ functions

………………………………………………………………………………..………15

3.Function explanation ………………………………………………………………………...……… 15

4.Menu explanation………………………………………………………………………………………16

5.Camera menu setting…………………………………………………………………………..…….. 16

6.Dial switch setting…………………………………………………………………………………..….21

Appendix Ⅰ

ⅠⅠ

Ⅰ…………………………………………………………………………………………..…..… 24

1.P protocol……………………………………………………………………………………….........… 24

2.D protocol…………………………………………………………………………………………...... …26

3.RS-485 Control and feedback data protocol…………………………………………………...... …27

4.Target angle control communication protocol……………………………………………...... …28

Appendix Ⅱ

ⅡⅡ

Ⅱ Troubleshooting ……………………………………………………………………… ……29

1.About image……………………………………………………………………………………….... .… 29

2.About control……………………………………………………………………………………….....…30

3.About installation…………………………………………………..…………………………….....… .30

3

Chapter 1: INSTALLATION MANUAL

1.PREFACE

This manual introduces the function, installation and operation of the integrated speed dome

camera in details. Please thoroughly familiarize yourself with the information in this manual prior to

installation.

This series dome cameras are equipped with DSP integrated camera, in-built zoom lens and

decoder controller.

Protocol P/D is used in this series dome cameras. It can support most popular system

platforms, such as: PELCO, MAXPRO. This manual will not explain the operation of other system if

connecting with other system, please contact with the system manufacture or dealer.

2.SAFEGUARD AND WARNING

Prior to installation and use of this product, the following WARNING should be observed. This

product can be only used in specified range in order to avoid any damage or danger.

 Installation and servicing should only be done by qualified service personnel;

 It must not be installed where exposed to rain and moisture and it can not be used in

unqualified temperature, humidity and power supply.

 Only use replacement parts recommended by manufacturer.

 After replacement/repair of this unit’s electrical components, conduct a resistance

measurement to avoid short circuit or turnoff.

 Please use the soft cloth to clean the dome. Use neuter cleanser if bad smeared. No use the

strong or corrosive cleanser avoiding scuffing.

 Be cautious of moving, never press the drive parts heavily avoiding dome troubles.

 The installation materials should be capable of supporting four times the weight of the

enclosure, pan/tilt, camera and lens combination.

Please thoroughly read this manual prior to installation and operation

3. SPECIAL ATTENTION

(Prior to installation and use the speed dome, the following issues should be observed)

 Standard voltage is 24VAC，

，，

，the best range is 24VAC±

±±

±10%. The speed dome will have

abnormal hidden trouble if the voltage is too high or too low for long time. Power supply

should be kept more than 60W, otherwise the speed dome may reset or abnormal control.

 The camera should not towards to strong light for long time, otherwise the CCD will easily

disabled, which will cause video lost or video anamorphic.

 The speed dome has good waterproof, damp proof capability, reach IP66 standard. But if

the user doesn’t install the wirings in correct way, the rain will enter the dome drive along

4

the cabling, which will cause short circuit of the PCB board even damage the camera. Be

notice that our pendent bracket can not be used for outdoor. Please refer the following

installation of wirings:

 Connect the power supply, video, control cables according to the instruction as following

picture:



 Note：

：：

：1.Cover the BNC head with rubber cover after connect the video BNC, to avoid the

BNC touch other metal.



2.RX＋

＋＋

＋.RX－

－－

－ is the anode and cathode of RS-485, do connect them as the above

picture, otherwise the speed dome can’t be controlled normally.



3.It will be better if can connect the EARTH wiring. By connecting to the earth, the

5

RS-485 and video port can pass 10/700us 1500V differential-mode and

4000Vcommon-mode lightning strike and surge testing. Which reach ITU－

－－

－T

K21－

－－

－2003

international lightning proof standard and GB9043 standard. But it can’t prevent direct

lightning stroke, will need additional device.



 4.Requirements for the connect cables

Requirements for the 24VAC power supply cable

Normally, the power wires have some resistance. There is some loss during voltage

transmission. The longer the wire is and the smaller the wire diameter is the worse loss will be.

Please refer to following wire diameter and distance requirement in order to avoiding the abnormal

work caused by insufficient voltage.

Power supply cable

diameter

0.5mm²(20#) 1.0mm²(18#) 1.5mm²(16#) 2.5mm²(14#)

Dome camera distance 11m(37ft) 18m(60ft) 29m(95ft) 46m(152ft)

Requirements for the video cable

The video wire also has inner loss as the power wire. The more the wire is and the small the

specification is, the worse loss it will be. The high the signal frequency is, the obvious the loss is.

The normal video wires models and the MAX. Transmission distance is listed in following table:

Video cable model Max. transmission

distance

Video cable model Max. transmiss

ion

distance

75-2 About 150m 75-5 About 370m

75-3 About 200m 75-7 About 500m

75-4 About 270m

75-9 About 680m

Requirements for RS-485 control cable

RS-485 cable transmission distance is relative to the cable diameter, transmission rate and

electro-magnetic interference condition. For examples: with a 1.0mm² twisted pair, if under 9600b/s

transmission rate, the longest transmission distance is 800M; if under 4800b/s transmission rate,

the longest transmission distance is 1000M; and if under 2400b/s transmission rate, the longest

transmission distance is 1200M.

Sometimes the installer use star connection mode, which doesn’t meet the industry standard

for RS-485 requirement. If the devices distance is far, it may cause signal reflect, reduce

Anti-interference capability and the camera will lose normal control. The suggestion is to parallel

connect a 120 ohm resistance at the fastest RS-485 anode and cathode; or adopt RS-485 distributor.

6

4. STRUCTURE OF HIGH SPEED DOME CAMERA (SEE PICTURE)

This series of Indoor/outdoor pendent speed dome camera contains three parts. Inspect each

box to make sure all parts are present.

Indoor/outdoor pendent speed dome camera contains following parts:

1. Back box

2. Dome drive

3. Lower dome

5.MAIN FUNCTION FEATURES：

：：

：

 Aluminum-alloy back box, 6 inches polycarbonate, integrated design

 Indoor and outdoor pendant installation

 Accurate motor driving, without shocking, nosing during operation

 High-reliability, built-in data never lost when the power is off.

 RS-485 displays pan/tilt orientation, preset target angle.

 Displays pan/tilt orientation and camera zoom

 Built-in function menu, camera and pan/tilt can be set.

 Powering-on self-restoring-----users can assign the movement after powering on.

 Multi-automatic scan pattern, scan speed can be set by the inside menu.

 Function of video freeze, wide dynamic, and backlight compensation.

 Day and Night camera can be set to single color or backlight pattern according to the needs of circumstance.

 Memory of pattern track function, can memory the preset transfer and all standards P/T/Z track.

 Pan/tilt controlling speed’s self-restoring, pan/tilt speed and the depth of zoom lens declines proportionally.

 Function of pattern track function, can memory the preset transfer and all standards P/T/Z track.

 256 preset positions, which precision error less than 0.1°

°°

°preset target speed: 250°

°°

°/second for pan and 150°

°°

°

/second for tilt.

7

 Variable self-touring speed can be set to1°

°°

°～

～～

～ 40°

°°

°/second.

 8 preset touring function: if the stopping time is between 5 sec and 60 sec can be set by the inside menu.

 360°

°°

°continuously pan rotation, tilt rotation with self-flip.

 Pan manual control speed: 0.1°

°°

°～

～～

～150°

°°

°/sec, tilt manual control speed:0.1°

°°

°～

～～

～100°

°°

°/sec

 7 alarming input, 2 AUX output.

 Inside waving and lightening protection

 Meeting IP66, CE, ROHS,FCC standards

6. Installation of the speed dome camera

STEP 1 Locate the Install Position

NOTE: Please make sure to airproof and damp-proof when the camera is outdoor installation.

1. Mount and install the back box, please refer to the manufacture’s install explanation. Insert the video ,

control and electrical wires into suspended bracket, and fix it.(see picture 1)

2. Press the environing spring and open the hinged door in the back box.(see picture 2)

3. Insert the video, control and electrical (or warning) wires into the back box through the mount.

4. Tighten the back box into the mount. If it is the outdoor installations, please thread the compound to the

threads in the back box.(see picture 3)

Picture 1 picture 2 Picture 3

STEP 2 Wire Circuit Board

Attach the wiring to the interconnected circuited circuit board inside the back box. When the powering on,

the red LED will light.

NOTE: Please refer to the TROUBLESHOOTING section, if the red LED does not light.

8

STEP 3 Install Dome Drive

GREEN TAB RED TAB

1. Set the protocol, baud rate, dome address and camera type for the needed position.

2. Line up the integrated dome drive’s red and green tabs with the green and red labels. Push the green tab

into the green label and the red tab into the red label, till both sides click into place.

3.

STEP 4 Install lower Dome

1. Apply lubricant to the O-ring. Install the O-ring in the groove on the trim ring of the lower dome.

2. Attach the back trim leash to the lower dome. Use retainer screw (nearest to a mounting screw) inside

lower dome.

Push the lower dome into the back box, line up the mounting screw holes, and install the two mounting screws.

7. SPECIFICATION

6.1STRUCTURE

Back box Aluminum alloy

Dome Drive Aluminum alloy, ABS Poly

Lower Dome Aluminum alloy, polypropylene Transparent Cover

Weight (approximate)

Unit weight Gross weight

3.5 kg 6 kg

Operation Environment indoor/Outdoor style

Working temperature -40°

°°

°～

～～

～50℃

℃℃

℃

Measurement See measurement drawing (unit: mm)

9

6.2 Rotation Index (only for Dome Drive)

Horizontal rotation 360°

°°

°continuous pan rotation

Vertical rotation 0°

°°

°～

～～

～92°

°°

°rotation

Manual control speed:

Pan 0.1°

°°

°～

～～

～150°

°°

°/sec manual operation

Tilt 0.1°

°°

°～

～～

～100°

°°

°/sec manual operation

Preset speed:

Pan 250°

°°

°/sec

Tilt 150°

°°

°/sec

6.3 Electrical index (only for Dome Drive)

Input voltage 18-30VAC; 24VAC

Input power 30VA

Fuse 2.0A

10

6.4 Camera, Lens parameters (Example)

Model 18×color

SONY

18×

day & night

SONY

26×

day & night

SONY

36×

day &

night

SONY

36×

day &

night

SONY

Optical Zoom

18 18 26 36

Electronic Zoom

12

Signal system

PAL/NSTC

Touring System

2:1 interleaved

CCD

1/4”CCD 1/4”HAD CCD

Horizontal

Resolution

>480TVL >540TVL

Lens

F1.4

(f=4.1~73.8mm)

F1.4

(f=4.1~73.8mm)

F1.6

(f=3.6~91mm)

F1.6~4.5

(f=3.4~122.4mm)

Pan angle

4.1mm wide

angle

Lens 48

0

73.8mm tele

angle

Lens 2.8

0

4.1mm wide

angle

Lens 48

0

73.8mm tele

angle

Lens 2.8

0

3.5mm wide

angle

Lens 54.2

0

91mm tele

angle

Lens 2.2

0

3.4mm wide angle

Lens 57.8

0

122.4mm tele angle

Lens 1.7

0

Focus

Auto/Manual First

Minimum

illumination

1/50 sec Shutter

speed(Color)1.0Lux

1/50 sec Shutter

speed

(Color)0.7Lux

1/3 sec Shutter

speed

(B&W)0.1Lux

ICR ON shutter

speed

(B&W) 0.01Lux

IR

1.0lux,1/5

sec

0.2lux,1/3

sec

ICR-ON

mode

0.15lux, 1/50

sec

0.01 lux,1/3

sec

IR

1.0Lux,1/60 sec

0.1Lux,1/4 sec

Night mode

0.1Lux, 1/4 sec

IR

Sync system

Inner Sync/AC linear lock

Inner/outer sync

Shutter Speed

Auto 1/50-1/10000 Auto 1/1-1/10000 Auto

1/3-1/10000

Auto 1/1-1/10000

Iris Ctrl

Auto/ Manual first Auto

Gain Ctrl

Auto/ Manual

Video Output

1.0+0.2VP-P(75ohm,compound) 1.0VP-P

S/N Ratio

50dB >50dB

White Balance

Auto/Manual

WDR

NO

11

Model 22×color

HITACHI

23×

day & night

HITACHI

30x

day & night

HITACHI

35×

day & night

HITACHI

27×

day & night

LG

Optical Zoom

22 23 35 35 27

Electronic Zoom

10 12 10

Signal system

PAL/NSTC

Touring System

2:1 interleaved Between lines 2:1 interleaved

CCD

1/4”CCD 1/4”HAD CCD 1/4”CCD

Horizontal

Resolution

>480TVL >540TVL >480TVL

Lens

F1.6

(f=4~88mm)

F1.6

(f=3.6~82.8mm)

F1.6

(f=3.4~102mm)

F1.6

(f=3.4~119mm)

F1.6

(f=3.6~98mm)

Focus

Auto/Manual First

Minimum

illumination

1.0Lux Color:1.0 Lux

B&W: 0.01 Lux

Color:1.0

Lux(PAL)

B&W: 0.01 Lux

Cut IR

Color:1.0

Lux(PAL)

B&W: 0.01 Lux

Cut IR

Color: 0.3 Lux

B&W:0.01Lux

Sync system

Inner Sync

Shutter Speed

Auto

1/50-1/30000

Auto 1/1.5-1/30000 Auto 1/1.5-1/30000 Auto

1/1.5-1/30000

Auto

1/50-1/10000

Iris Ctrl

Auto/ Manual first

Gain Ctrl

Auto/ Manual

Video Output

1.0VP-P(75ohm,compound output)

S/N Ratio

50dB

White Balance

Auto/Manual

WDR

NO YES YES YES NO

12

Chapter 2 OPERATION

1. BASIC FUNCTION EXPLANATION

After connect all wirings as the instruction and turn on the power, the dome camera will display

it’s configure information. And after configuration is done, the menu will show configure OK

information. If the user sets the POWER UP DONE, the dome will execute this movement and

the tips information disappear; if the user does not set the POWER UP DONE, the tips

information will be kept until the dome camera receive the control command, then the tips

information will disappear and show the system communication control is normal.

Power up display:

When configuring:

Configure OK:

NOTE: 1. VERSION 1.10 is the software version number of the dome camera, and it will change

as the product’s upgrade.

2. PROTOCOL P is control agreement, can support P, D protocol, and it will change as

the dial switch chooses different protocol.

3. ADDRESS 1 is control address, can support 256 addresses, and it will change as the

dial switch chooses different protocol.

4. COMM 4800.N.8.1 is communication information, 4800 is communication baud rate,

VERSION 1.10

PROTOCOL P

ADDRESS 1

COMM 4800.N.8.1

POWER UP DONE

VERSION 1.10

PROTOCOL P

ADDRESS 1

COMM 4800.N.8.1

CONFIGURING

VERSION 1.10

PROTOCOL P

ADDRESS 1

COMM 4800.N.8.1

CONFIGURE OK

13

there are 1200, 2400, 4800, 9600 four baud rate for different dial switch. N.8.1 means no verify, 8

data byte, 1 dwell position.

After the dome finish configure, the user can operate the dome as the following method

Operate Procedure

Pan/Tilt

1. To rocker control keyboard, camera will rotate to the operation

direction if the rocker leans to one direction of up/down/left/right.

The speed depends on the distance between rocker and center. The

camera will move slowly to the operation direction if move the

rocker lightly in one direction. The camera will speed to MAX.

Speed of continuously move the rocker in one direction. The

camera will stop when the rocker returns to the center.

2. To 2-dimension control keyboard, the camera will rotate to the

operating direction if press direction key. The speed depends on

the current speed code. To our KBD100 keyboard, press any one of

1-9, and then press direction key. The pressed number key is the

speed stage. The larger number it is, the higher speed will be. The

camera stops action of release the key.

3. To computer software control, press the direction key of control,

the camera will rotate to the operating direction. The speed

depends on current speed code. Some software can implement

continuous rotation and some only can implement dot movement.

Please refer to the software instruction provided by the

manufacture for detailed operations.

This dome can do 360

0

continuous pan rotation and +2

0

~-92

0

vertical rotations. It will stop rotate when reaching tilt limit.

STOP SCAN Preset 96(hit“9”+“6”+ “Preset”)

PRESET TOUR

Preset 98(hit“9”+“8”+ “Preset”)

PATTERN

1.press pattern scan setting to start

2. run the camera as the designed route

3.press pattern scan setting to stop

4.run the pattern scan, the camera will run the recorded route

AUTO SCAN Preset 99(hit“9”+“9”+ “Preset”)

ZOOM WIDE

1.Press the ZOOM WIDE button or turn the joystick clockwise until

you have the picture you want

2.release the button or joystick

ZOOM TELE

1.Press the ZOOM TELE button or turn the joystick anti-clockwise

until you have the picture you want

2.release the button or joystick

14

IRIS OPEN

Continuously press key OPEN to open iris and increase brightness

gain

IRIS CLOSE

Continuously press key CLOSE to close iris and increase

brightness gain

FOCUS NEAR

Continuously press key NEAR, focus become near from far, the

image becomes fog from clear or becomes clear from fog.

FOCUS FAR

Continuously press key FAR, focus become far from near, the

image becomes fog from clear or becomes clear from fog.

PRESETS

1. When set presetting, press “preset No.”+ key ”PRESET”(about

for 3 seconds)

2. when use presetting, press “preset No.”+ key ”PRESET”

3. Please refer to operation instruction book for controller.

Remarks:

The following stipulations are for presetting,

Preset() function

1-8 Tour

1-7 Preset positions for Alarming input

33 180º flip

34 lever home place

79 Open zoom on

80 Close zoom on

81 Auto low lux shift

82 Open low lux shift （

（（

（B&W menu）

））

）

83 Close low lux shift （

（（

（color menu）

））

）

84 Open wide dynamic

85 Close wide dynamic

86 Open Backlight Compensation

87 Close Backlight Compensation

88 Open video freeze

89 Close video freeze

92-93 Scan control limit

94 Exit menu

95 Enter menu

96 Scan stop

98 Preset tour

99 Auto scan

15

2. PTZ FUNCTIONS

This series of high-speed dome camera manual pan speed 0.1 º -150 º/second, manual tilt

speed 0.1 º ~100 º/second.

Pan/tilt speed and lens zoom is proportional, darker the lens zoom, slower the speed is!

The current position of P, T, Z three orientations (presetting positions) can be stored and

repeat use.

3. Function explanation

3.1 Screen menu function

It has screen menu function. All information can be displayed by menu to set the function

and parameter (only for LG and CNB camera)

3.2 Multi-cameras control function

Select different camera only by mending dial switch setting, no any hardware or software

needed. It supports LG, SONY, HITACHI, CNB cameras.

3.3 Proportion speed function

Horizontal and tilt speed change automatically with the zoom changes. When zooming

wide, the camera speeds down; then zooming narrow, the camera speeds up to catch better

tracing effect.

3.4 AUTO SCAN

Auto scan refers to the function of 360

0

continuous scan the images at certain speed on

the horizontal lever when keeping the pitching angle unchanged. The left and right limits can

be set for continuous scan at certain speed on the horizontal lever.

3.5 AUTO FLIP

When the camera tilts downward and goes just beyond the vertical position, the dome

rotates 180

0

. When the dome rotates, the camera starts moving upward as long as you

continue to hold the joystick in the down position. Once you let go of the joystick after the

dome rotates, joystick control returns to normal operation. The auto flip function is useful for

following a person who passes directly beneath the camera.

3.6 PRESET

Any position of dome camera PTZ can be conserved. We call it preset (pre-established

position). The preset can be transferred and cleaned.

3.7 PRESET TOUR

The dome camera will transfer pre- established preset 1-8 every 10 second. It will leap over

to next preset position if position in not among 1-8.

3.8 ZERO TEST

The dome camera will turn to horizontal and tilt zero by preset 34 when the inevitable

desynchronizing appears or the operator wants to find zero position during working process. It

can reset the orientation and is convenient for operators.

3.9 LOW SENSITIVITY (COLORS/BLACK AND WHITE SWIFT) FUNCTION

The camera automatically changes CCD sensitivity according to surrounding light. Color

image changes to black& white one in low sensitivity; black& white image changes to color

one in high sensitivity.(related to camera)

3.10 AUTO FOCUS MODE

The camera automatically adjusts lens focus to keep clear image if auto focus mode.

16

Manually operate FAR or NEAR focus adjustment can also adjust focus. The dome camera will

recover auto focus adjustment function if operate horizontal, vertical rotation or control lens

zoom.

3.11AUTO IRIS FUNCTION

The camera automatically adjusts iris to keep normal brightness in auto iris mode.

Manually operate OPEN or CLIOSE iris adjustment button can also adjust iris. The dome

camera will recover auto adjustment function if operated horizontally, vertical rotation or

control lens zoom.

3.12 BACKLIGHT COMPENSATION

The object will become black as the shadow if strong light appears in background.

Backlight compensation function can compensate the brightness automatically to dark

objects in bright light background and adjust the brightness background to avoid the image

full of brightness and get clear image. Too strong backlight can make the object illegibility.

4. MENU EXPLANATION

4.1 Operation explanation

This dome camera has in-built menu to set parameters for cameras and lens. The

contents in this chapter can make you a complete knowledge of this camera and do some

settings according to users’ requirements.

The basic operation contains move menu bar, enter next menu, return former menu,

change setting, verify change and cancel change.

Control up and down command: move menu bar and change setting

Iris open command: enter camera menu or select menu to verify change

Iris closed command: return former menu and cancel change

4.2 OPEN/EXIT MENU

This dome camera opens menu by preset 95 and exit by preset 94 according to P control

protocol. Please refer to controller instruction book for other control equipments.

Press “9”+”5”+”PRESET”

Press key 95+ PRESET to enter dome camera menu

Press “9”+”4”+”PRESET”

Press key 94+ PRESET to exit dome camera menu

5. OPEN MAIN MENU

This series dome camera is stipulated according to P/D protocol, and use

preset position No.95 to open the main menu. For other protocol equipment,

please refer to protocol instruction.

NOTE:

1. “< >”symbol means it contains next menu

2. use “up, down” key to move cursor “→

→→

→”, use “OPEN or CLOSE” key to

confirm or exit the menu

17

3. when press “OPEN” key, the cursor becomes”

””

”★

★★

★”, then can use “UP or

DOWN” key to amend the parameter; press OPEN key when finish your

amendment.

5.1 MAIN MENU

NOTE; this instruction book’s example is for

23×

××

× day& night camera, and it will be

Some changes for other cameras.

5.2 SECOND MENU

COMM

PROTOCOL

ADDRESS

VERSION

AUTO EXIT TIME, 5,6,7,8,9,10 minutes

NOTE: Except AUTO EXIT TIME, other items can only be showed not change in the

menu.

5.3 SECOND MENU

<CAMERAⅠ

ⅠⅠ

Ⅰ>

<CAMERAⅡ

ⅡⅡ

Ⅱ>

<PANTILTⅠ

ⅠⅠ

Ⅰ>

<PANTILTⅡ

ⅡⅡ

Ⅱ>

<ALARM>

<AUX>

PRESET DOME

DOME SETTINGS

<CAMERAⅠ

ⅠⅠ

Ⅰ>

<CAMERAⅡ

ⅡⅡ

Ⅱ>

<PANTILTⅠ

ⅠⅠ

Ⅰ>

<PANTILTⅡ

ⅡⅡ

Ⅱ>

<ALARM>

<AUX>

PRESET DOME

BACK

SYETEM INFORMATION

COMM 2400,N,8,1

PROTOCOL P

ADDRESS 1

VERSION 1.10

AUTO EXIT TIME 10

BACK

EXIT

18

5.4 THIRD MENU

5.4.1 CAMERA MENU Ⅰ

ⅠⅠ

Ⅰ

AUTO FOCUS

ZOOM LIMIT

ZOOM SPEED

AUTO SHARPNESS

SHARPNESS LEVER

AUTO WHITE BALANCE

R GAIN

B GAIN

VIDEO FREEZE

WDR

AUTO FOCUS: ON & OFF, default setting is ON

ZOOM LIMIT: different camera with different zoom, default setting is X276

ZOOM SPEED: 4.2S& 5.8S, default setting is 4.2S

AUTO SHARPNESS: ON&OFF, default setting is ON

SHARPNESS LEVEL: 1~63 levels, default setting is 20

AUTO WHITE BALANCE: ON& OFF, default setting is ON

R GAIN: 0~1023, default setting is 180

B GAIN: 0~1023, default setting is 180

VIDEO FREEZE: ON & OFF, default setting is OFF

WDR (only for HITACHI VK-S454 camera): ON& OFF, and it can available only when the

backlight compensation setting is OFF.

5.4.2 CAMERA MENU Ⅱ

ⅡⅡ

Ⅱ

SHUTTER MODE

SHUTTER SPEED

AGC MODE

GAIN

AUTO IRIS

AUTO IRIS LEVEL

AUTO IRIS PEAK

BACKLIGHT COMP (BLC)

DAY/NIGHT MODE

DAY/NIGHT

SHUTTER MODE: AUTO& MAN, default setting is OFF

SHUTTER SPEED:1/1.5~1/30000, default setting is 1/50

AGC MODE: AUTO& MAN, default setting is AUTO

GAIN: 1~30Db, default setting is 6Db

AUTO IRIS: ON&OFF, default setting is ON

AUTO IRIS LEVEL: 1~100(available only when AUTO IRIS MODE IS OFF), and default

setting is 66

AUTO IRIS PEAK: 1~10, default setting is 10

CAMERA Ⅱ

ⅡⅡ

Ⅱ

SHUTTER MODE AUTO

SHUTTER SPEED 1/50

AGC MODE AUTO

GAIN 6dB

AUTO IRIS ON

AUTO IRIS LEVEL 66

AUTO IRIS PEAK 8

BACKLIGHT COMP(BLC) OFF

DAY/NIGHT MODE AUTO

DAY/NIGHT DAY

BACK

CAMERA Ⅰ

ⅠⅠ

Ⅰ

AUTO FOCUS ON

ZOOM LIMIT X276

ZOOM SPEED MEDIUM

AUTO SHARPNESS AUTO

SHARPNESS LEVER 10

AUTO WHITE BALANCE ON

R GAIN 180

B GAIN 180

VIDEO FREEZE OFF

WDR OFF

BACK

19

BACKLIGHT COMP (BLC): ON& OFF, default setting is OFF

DAY/NIGHT MODE (only for SONY-FCB480, SONY-FCB980, HITACHI VK-S454):

AUTO& MANUAL, default setting is AUTO

DAY/NIGHT (only available when DAY/NIGHT MODE IS MANUAL): DAY COLOR&

NIGHT B&W, default setting is AUTO

5.4.3 PAN& TILT MENU Ⅰ

ⅠⅠ

Ⅰ

AUTO FLIP

PROPORTIONAL PAN

PARK ACTION

PARK TIME

SCAN SPEED

AUTO FLIP: ON& OFF, default setting is ON

PROPORTIONAL PAN: ON& OFF, default setting is ON

PACK ACTION: NONE, 1PRESET~8PRESET, AUTO SCAN, PRESET TOUR,

PATTERN total 12 classes. And default setting is NONE.

PARK TIME: 0~60 minutes, default setting is 30.

PRESET TOUR TIME: 5~60 minutes, default setting is 10

SCAN SPEED: 1~40, default setting is 20

5.4.4 PAN& TILT MENU Ⅱ

ⅡⅡ

Ⅱ

LIMIT STOPS

MANUAL STOPS

SCAN STOPS

ANGLE DISPLAY

SET AZIMUTH ZERO

LIMIT STOPS: ON& OFF, default setting is OFF

MANUAL STOPS: ON & OFF, default setting is OFF

SCAN STOPS: ON & OFF, default setting is OFF

ANGLE DISPLAY: ON & OFF, set ON to display the pan& tilt angle and zoom, default

setting is ON.

SET AZIMUTH ZERO: Azimuth zero can set the camera to the zero position, then press

iris OPEN key to make sure azimuth zero.

5.4.5 POWER UP ACTION

POWER UP ACTION

POWER UP TIME

POWER UP ACTION: NONE,1PRESET~7PRESET, AUTO SCAN, PRESET TOUR,

PANTILT Ⅰ

ⅠⅠ

Ⅰ

AUTO FLIP OM

PROPORTIONAL PAN OFF

PARK ACTION NONE

PARK TIME 30

PRESET TOUR TIME 10

SCAN SPEED 10

BACK

PANTILT Ⅱ

ⅡⅡ

Ⅱ

LIMIT STOPS OFF

MANUAL STOPS OFF

SCAN STOPS OFF

ANGLE DISPLAY ON

SET AZIMUTH ZERO

BACK

POWER UP

POWER UP ACTION NONE

POWER UP TIME 10

BACK

20

PATTERN 12 classes, default setting is NONE.

POWER UP TIME: 1~10 minutes, default setting is10.

5.4.6 LINE SYNC

LINE SYNC

LINE SYNC PHASE

LINE SYNC: ON & OFF, default setting is OFF

LINE SYNC PHASE: 0~359, default setting is 0

5.4.7 ALARM INPUTS

ALARM1

ALARM2

ALARM3

ALARM4

ALARM5

ALARM6

ALARM7

ALARM1: 1~7 preset positions, press PATTERN to activate, default setting is1.

ALARM2: 1~7 preset positions, press PATTERN to activate, default setting is2.

ALARM3: 1~7 preset positions, press PATTERN to activate, default setting is3.

ALARM4: 1~7 preset positions, press PATTERN to activate, default setting is4.

ALARM5: 1~7 preset positions, press PATTERN to activate, default setting is5.

ALARM6: 1~7 preset positions, press PATTERN to activate, default setting is6.

ALARM7: 1~7 preset positions, press PATTERN to activate, default setting is7.

5.4.8 AUX OUTPUT

AUX1 MODE

AUX2 MODE

AUX1 MODE: 5V output, can activate it by alarm input or keyboard, default setting is alarm.

AUX12 MODE: Relay output, can activate it by alarm input or keyboard, default setting is alarm.

LINE SYNC

ON

LINE SYNC PHASE 0

BACK

ALARM

ALARM1 1

ALARM2 2

ALARM3 3

ALARM4 4

ALARM5 5

ALARM6 6

ALARM7 7

BACK

AUX

AUX1 MODE ALARM

AUX2 MODE ALARM

BACK

Page is loading ...

Dante DLM1985 Operating instructions

This manual is also suitable for

Dante DLM1985 Operating instructions

Related papers

Other documents