CTA 434185 User manual

Brand: CTA

Model: 434185

Type: User manual

888-733-4448888-733-4448

AUT-CFVMH

INSTRUCTION - MANUAL

Package Contents:

Intructions:

1. Assembling Security Holder to the Vehicle Mount

2. Assembling Rail Clamp Footing of the Vehicle Mount

Because each vehicle is different, you will need to determine which included seat rail clamp is best for you.

5. How to Insert a Tablet

6. How to Setup the Foam

Custom Flex Vehicle Mount

w/ Security Universal Holder

6A. Peel off the adhesive sticker on the backside. Then, stick on the appropriate foam back so that your tablet can fit into the holder securely. If there is still

movement when your tablet is in the holder, then try a different foam or combination of foams until it’s tightly fitted. You can use just one foam or stack different

foam pieces together for the best available fit.

2A. Choose the clamp base (J) with the angle that matches your

needs.

2B. Align the preferred clamp (J) and the vehicle mount (B) and rotate in

screw (H) with provided allen key tool (I).

4A. Twist the screw knobs counter-clockwise to release the connection.

Adjust the arm to your any preferred position & rotate clockwise until

securely tightened

4. How to Adjust the Joints

3A. Loosen the bolt (not included) of

the seat rail.

3B. Install the full assembled vehicle

mount on the seat rail and screw the

bolt back as shown. (Tool not included)

3. Installing Vehicle Mount to your Vehicle Seat Rail

7. Setting up Cable Management / Cable Routing

7A. Take the rubber component (B), insert into the holder arm (A) as shown above.

Take the power cord and loop it into the rubber component as shown. While the tablet

holder is in unlocked mode and arms extended out, insert your tablet aligning the

charging port side with the charging power cord and plug in. Slide the arms back

around the tablet until securely tightened afterwards. Set the holder into locked mode

and lock with security key afterwards.

7B. Fish the power cord in the back as shown. Locate the

clips at specific corners to hold the cord in place and then

guide the cord out towards the outlet or whatever power

source as needed.

180° 90° 45°

M4 Nut M4 x 10

M10 Allen Key Vehicle Seat Rail

Clamps Bundle

x4 x2

x1 Stack of 4 Piece

Foam Adapters

x1 x1

BCDE F G

M10x12L

M4 Allen Key

M4 Nut

M4 x 10 x4

1A. Align VESA plate holes of the vehicle mount (B) to the VESA holes of the security holder (A). Place hex nut (E) on the front side of the holder VESA in the

hex hole using your fingers. Rotate in screws (F) with the provided tool (D) from behind until securely tightened.

5A. Unlock by moving

the lever over to the

unlock position

5B. Extend the holder

arms by pulling outward

5C. Insert device

on the loosen arms

as shown above

5D. Push arms back

towards the tablet until

securely tightened. Then

move the lever back into

lock position.

Caution: Holder arms can only be adjusted in “unlocked” setting. Make sure the

lever is in the right position before attempted to adjust.

**Tablet shown for

illustration

purposes only and

not included.

Caution: Holder arms can only be adjusted in “unlocked” setting. Make sure the

lever is in the right position before attempted to adjust.

5E. Insert key to unlock holder, then

make sure the lever is in the

‘unlocked’ setting position. Only then

can you adjust holder arms. When

locking with key, it prevents any user

from putting the lever in locked or

unlocked setting mode.

View from Side of Stacking Foams

Foam

Backing

**Tablet shown for

illustration

purposes only and

not included.

**Vehicle Seat and Rail and Additional Hardware Not Included

CTA 434185 User manual

CTA 434185 User manual

Related papers

Other documents