WaterWorks HNWS02 Installation guide

WaterWorks
Brand
WaterWorks
Model
HNWS02
Type
Installation guide
TECHNICAL DETAILS:
DETAIL SPECIFICATION
ADJUSTABLE LEVELERS/FEET YES
DIAMETER OF LEGS/TUBES 1 ½ ” [38mm]
PRIMARY MATERIAL Brass
RECOMMENDED ROUGH-IN SUPPLY HEIGHT 21” [533mm]
RECOMMENDED ROUGH-IN SUPPLY SPREAD 9” [229mm]
RECOMMENDED ROUGH-IN WASTE HEIGHT 19” [483mm]
STORAGE CAPACITY 28½” [724mm] x 17⅝” [448mm]
TOP ATTACHMENT METHOD Silicone
WEIGHT 18lbs
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
INSTALLATION GUIDELINES
IMPORTANT:
Ø To ensure this product is installed properly, you must read and follow these guidelines.
Ø The owner/user of this product must keep this information for future reference.
Ø Install adequate blocking or position over a stud to properly secure the fixture.
Ø Inspect this product, upon receiving, to ensure it is the correct model and you have all parts
required for proper installation.
Ø Slab top, fittings and lavatory sold separately.
Ø This product must be installed by a professional licensed contractor. Be sure your
installation conforms to all federal, state, and local codes.
Ø Take all necessary precautions to ensure that this product is protected during installation.
Ø Ensure the floor is level and the weight of this product will be adequately supported.
Ø The use of certain plumber’s putty may stain stone or tile surfaces.
UPDATED ON 08.08.2022
=
Ø
Ø
181/16” [469mm]
2515/16” [659mm]
29” [737mm]
31/16” [78mm]
313/4” [806mm]
11/2” [38mm] 277/8” [469mm]
181/16” [469mm]
2513/16” [655mm] 55/16” [151mm]
20” [508mm]
15” [382mm]103/8” [264mm]
STYLE No. HNWS02
Henry Metal Round 2 Leg Washstand
29” [737mm] x 20” [508mm] x 31¾” [806mm]
INSTALLATION GUIDELINES
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM UPDATED ON 08.08.2022
A B
C
7. Measure/mark the positions for the Wall Screws (for Custom - place the washstand against the wall).
8. Place a level on top of the washstand legs and adjust the feet accordingly until it is level.
9. Mark the vertical center line (for the Waste) and ensure it is equal on either side of the washstand legs.
10. Using a pencil, mark the position of the bottom rail screw (for Custom - mark through holes).
11. Using a pencil, mark the position of the top rail.
(for Custom - measure from floor to underside of rail, add ¾” [19mm] and mark hole position).
12. Drill holes in the wall (x 4) using a Ø7/32” Drill Bit - then push the anchors (H x 4) into the drill holes.
1. Place the parts on a protective sheet to avoid damaging any of the surface finishes during assembly.
2. Insert the horizontal Cross Rail into the leg connections as shown (Orientation identified by Left & Right
Labels).
3. When fully inserted, rotate the Cross Rail tube to expose the pre-drilled fixing screw hole.
4. Insert the Flat Head (E) and fully tighten using a Cross Head Screw Driver.
5. Secure both ends of the Cross Rail to the Leg Assemblies.
6. To remove the Wall Fixing Inserts (J) unscrew the Set Screw (F) using the 2mm Allen Key (I) and pull out
the inserts.
F
F
H
G
STYLE No. HNWS02
Henry Metal Round 2 Leg Washstand
29” [737mm] x 20” [508mm] x 31¾” [806mm]
H
o
I
13. Using the Wall Screws - attach the Wall Fixing Inserts securely to the wall.
14. Connect the washstand to the Wall Fixing Inserts and push on fully.
15. Secure the Side Rails to the Wall Fixing Inserts by tightening the set screws (F) using the 2mm Allen Key
(I).
16. Secure the bottom horizontal washstand legs in place by inserting Wall Screws (G) through the fixing
bracket & tighten.
17. MAKE ANY WATER CONNECTIONS AND FIX THE BASIN IN PLACE. Final leg adjustments can be made to
support the basin.
25 13/16”
[655mm]
10 1/16”
[256mm]
29”
[737mm]
==
Foot Adjustment
E - (2) M3 x 6mm Flat Head
G - (4) Wall Screws
F - (2) M4 x 6mm Set Screws
(Spares)
H - (4) Anchors
I - (1) 2mm Allen Key
Parts included ;
A - 1 x L/H Side Rail Assembly
B - 1 x R/H Side Rail Assembly
C - 1 x Cross Rail
D - 1 x Fixing Screw Pack
(contents listed above)
J - (4) Wall fixings
(Supplied pre-installed in tubes)
  • Page 1 1
  • Page 2 2

WaterWorks HNWS02 Installation guide

WaterWorks
Brand
WaterWorks
Model
HNWS02
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents