CONSET 501-37 8S 112-152 User manual

Brand
CONSET
Model
501-37 8S 112-152
Type
User manual

This manual is also suitable for

Assembly instruction
501-37
345500.1
EN
Page 2-3
ANSI / BIFMA X5.5 - 2014 tested and approved
2
TABLE OF CONTENT
1. SAFETY AND WARNINGS
2. USAGE
3. SET UP AND INSTALLATION
4. OPERATION
5. MAINTENANCE AND DEFECTS
6. TECHNICAL DATA
7. PARTS
8. ASSEMBLY INSTRUCTIONS
9. DECLARATION OF CONFORMITY
1. SAFETY AND WARNINGS
This table complies with the prescribed safety regulations. Inappropriate use may cause damage to persons and table.
Please read the operation manual prior to start using the table. It provides you with important information about safety, use,
installation and maintenance of the table, and thus protecting you and your children and avoiding damage on the table.
Please guard this operation manual and pass it on to any future owner !
IMPORTANT NOTES !
Prior to installment, use and
maintenance of the table frame, any
installer and any user of the table
must study this assembly and operation
manual carefully, so as to gain a complete
understanding of its contents.
2. USAGE
– The electromotive, height-adjustable tables are designed for workstations in dry work environments only ( 0 - 40 °C; 20 - 90 % relative
humidity ). The table height is innitely adjustable, so that it can be set to the most ergonomically suitable working level.
– They have not been designed for other purposes than those included in this manual, e.g. they are not to be used in areas of
high humidity or dampness, nor for lifting people. Any other use is at one’s own risk !
– Do not crawl, lie or move around under the table frame, and do not sit or stand on the table frame.
– CHILDREN should only use the table when supervised by adults.
– Liability : The manufacturer accepts under no circumstances warranty claims or liability claims for damages arising from improper
use or handling of the table frame other than that described in this operation manual.
3. SET UP AND INSTALLATION
When the table has been assembled ( see assembly instructions in CHAPTER 8 ) the adjustable feet are installed so that the table is level
and does not shift. Then the table is connected to the 100 -240 VAC outlet and the table is ready for use.
– Make sure that no cables can get jammed.
– Place the table in a safe distance from window frames, radiators, furniture etc. so that people do not get stuck.
– Do not place any objects above 21" ( 55 cm ) underneath the table.
– When moving the table after it has been assembled, the tabletop needs to be removed. The table CANNOT be lifted by the tabletop.
The desk need to be lowered to minimum height before moving.
4. OPERATION
UP/DOWN operation :
Push the buttons for operation up or down
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUC
TIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.
3
5. MAINTENANCE AND DEFECTS
– The table does not require any maintenance by usage as described in chapter 2 in the directions for use.
– The table is only to be maintained with a damp cloth.
– In the event of the occurrence of jarring sounds during operation, STOP using the table and please contact the dealer.
6. TECHNICAL DATA
Frame, materials : Steel, powder lacquered
Weights ( frame ) :
44 lbs
( 20 kg )
| 46 lbs
( 21 kg )
| 49 lbs
( 22 kg )
| 49 lbs
( 22 kg )
Width :
44 ⁄"
( 112 cm ) |
50 ¾"
( 129 cm ) |
59 ⁄"
( 152 cm ) |44 ⁄"-59 ⁄" ( 112 -152 cm )
Depth : 22" -39 ⁄" ( 60 -100 cm ) – depends on tabletop shape
Height ( frame ) : 21" - 47" ( 53 ½ -119 ½ cm )
V ( speed ) : ~1 ¼" / sec. ( ~32 mm / sec. ) – unloaded
Duty cycle : 10 % by 50 % of max. working load on frame or max. 2 min. continuously
Operation : Micro switches
Voltage : 100 -240 VAC
|
50 / 60 Hz
Standby consumption : < 0,5 Watt
Max. working load : 220 lbs ( 100 kg ) – on frame *
Tested peak load : 276 lbs ( 125 kg ) – on frame **
Above curve applies to a centrally placed load and is only valid in respect of duty cycle : 10 % by 50 % of max. working load or max. 2 min. continuously.
Above specications may vary depending on local temperature, humidity and input voltage.
7. PAR TS :
See page 4.
8. ASSEMBLY INSTRUCTIONS :
See page 5 -7.
9. DECLARATION OF CONFORMITY
We hereby declare, under our sole responsibility that the following products :
– Sit and stand table product type 501-37
is in accordance with:
– Directive 2006/42/EF of The European Parliament and of the Council of 17 May 2006 on machinery
and on changes of directive 95/16/EF
With reference to the above please be aware that:
– the sit and stand table is considered a machine and
– the sit and stand table may not be used until it has been assembled and installed according to the instructions.
Manufacturer :
ConSet A/S | Industrivej 23 | DK-6900 Skjern | Denmark
Tel. : +45 9680 0080 | Fax : +45 9680 0081 | www.conset.com | conset@conset.com
* **
4
C) x2
E) x 14
B) x1
D) x1
F) x4
G) x 4
2
3
6
4
5
1b
1a
7. PARTS
DO NOT CONNECT TO POWER
BEFORE THE DESK FRAME HAS BEEN
COMPLETELY ASSEMBLED!
5
F) x2
F) x2
G) x 2
G) x 2
2
3
1.
2.
1b
1a
8. ASSEMBLY INSTRUCTIONS
6
E)x10
B) x1 E) x2 5
4
C) x2
6
E) x2
D) x1
3.
4.
D) x1D) x1
7
5.
6. Do not over tighten the screws
since this may harm the function of the control
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

CONSET 501-37 8S 112-152 User manual

Brand
CONSET
Model
501-37 8S 112-152
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents