American Standard High Hamilton Elongated Space-saving One-Piece Toilet 2096.333 User manual

Type
User manual

This manual is also suitable for

© 2004 American Standard Inc.
10
HIGH HAMILTON™ELONGATED
SPACE-SAVINGONE-PIECE TOILET
VITREOUS CHINA
HIGH HAMILTON™ ELONGATED SPACE-
SAVING ONE-PIECE TOILET
Vitreous china
Low-consumption (6.0 Lpf/1.6 gpf)
One-piece toilet features a higher (427mm
16-13/16) bowl for added comfort
Elongated siphon action bowl and tank
with unique space-saving feature
Fits into the same space as a conventional
round front toilet
Color-matched trip lever
Internal trapway area fully glazed
Includes color-matched Rise and Shine
plastic seat and cover (#5324.019) with
easy-to-clean lift-off hinge system
2 bolt caps
100% factory flush tested
2096.016
2096.333
Right-hand trip lever
Nominal Dimensions:
692 x 457 x 699mm
(27-1/4" x 18" x 27-1/2")
Fixture only, supply by others
Compliance Certifications -
Meets or Exceeds the Following Specifications:
ASME A112.19.2M (and 19.6M) for Vitreous
China Fixtures - includes Flush Performance,
Ball Pass Diameter, Trap Seal Depth and
all Dimensions
To Be Specified
Color:
Supply with stop:
76mm
(3)
FINISHED WALL
16mm
(5/8)
427mm
(16-13/16)
184mm
(7-1/4)
13mm
(1/2)
481mm
(18-15/16)
692mm
(27-1/4)
164mm
(6-7/16)
243mm
(9-9/16)
305mm
(12)
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
457mm
(18)
FINISHED
FLOOR
*152mm
(6)
SUPPLY AS
REQUIRED
699mm
(27-1/2)
*152mm
(6)
229mm
(9)
368mm
(14-1/2)
C/L
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12")
FROM FINISHED WALL TO C/L OF OUTLET.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLY ARE SUGGESTED.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance
established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
MEETS THE AMERICAN DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
When installed, top of seat meets minimum requirement of
432 to 483mm (17" to 19") from the finished floor.
Revised 10/04
BARRIER FREE
NOTE: Roughing-in information shown on reverse side of page
© 2004 American Standard Inc.
11
HIGH HAMILTONELONGATED
SPACE-SAVINGONE-PIECE TOILET
VITREOUS CHINA
76mm
(3)
FINISHED WALL
16mm
(5/8)
427mm
(16-13/16)
184mm
(7-1/4)
13mm
(1/2)
481mm
(18-15/16)
692mm
(27-1/4)
164mm
(6-7/16)
243mm
(9-9/16)
305mm
(12)
C/L OF SEAT
POST HOLES
140mm (5-1/2)
CENTERS
457mm
(18)
FINISHED
FLOOR
*152mm
(6)
SUPPLY AS
REQUIRED
699mm
(27-1/2)
*152mm
(6)
229mm
(9)
368mm
(14-1/2)
C/L
NOTES:
THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12")
FROM FINISHED WALL TO C/L OF OUTLET.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLY ARE SUGGESTED.
SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance
established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
MEETS THE AMERICAN DISABILITIES ACT GUIDELINES AND
ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND
USEABLE BUILDING FACILITIES-CHECK LOCAL CODES.
When installed, top of seat meets minimum requirement of
432 to 483mm (17" to 19") from the finished floor.
BARRIER FREE
2096.333 RIGHT HAND HOLE TRIP LEVER
  • Page 1 1
  • Page 2 2

American Standard High Hamilton Elongated Space-saving One-Piece Toilet 2096.333 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI