Vulcan Hart VSCX26 Datasheet

Brand: Vulcan Hart

Model: VSCX26

Type: Datasheet

This manual is also suitable for

VSCX2

Vulcan Hart VSCX26 is a regenerated steam convection steamer on a cabinet base with a 24 Qt. tilting kettle. It features two stainless steel cooking compartments with coved interior corners, each of which can accommodate six 1" deep, three 2.5" deep, or two 4" deep 12" x 20" pans. The compartments have 1.25" drains, and the heavy-duty stainless steel "slammable" doors can be opened and closed during the cooking cycle without interrupting the steam supply. The tilting kettle is mounted to the right of the cooking compartments and is interconnected to the steam generator.

Item # __________________________

C.S.I. Section 11420

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. 1-800-814-2028

502-778-2791 QUOTE & ORDER FAX: 1-800-444-0602

A2780

ISO9001

Vulcan-Hart Co.

SPECIFICATIONS:

Regenerated steam generator convection steamer, Vulcan-Hart

Model No. VSCX26. Two stainless steel cooking compartments

with coved interior corners. Each compartment accepts six

1" deep, three 2

⁄2" deep or two 4" deep 12" x 20" pans. 1

⁄4" drain

in each compartment. Heavy duty stainless steel "slammable"

doors can be opened and closed at anytime during the cooking

cycle. Steam shuts off when door(s) are opened. Tilting kettle

mounted to right of cooking compartments and interconnected

to steam generator. Deck mount dual temperature faucet with

12" swing spout. Compartment controls include 60 minute dial

timer with buzzer, green "ready" and red "cooking" indicator lights.

Convection steamer mounted on 28" high base cabinet with

stainless steel front full height doors, slip-off stainless steel side

and aluminized steel rear panel with welded 6" stainless steel

legs rear with flange foot and front with bullet. Direct steam supply

at 40 to 50 PSI with a flow of 200 lbs. steam/hr.

Exterior dimensions: 44"w x 33"d x 72

⁄2"h.

NSF listed. Meets ASME code.

MODEL VSCX26

REGENERATED STEAM CONVECTION STEAMER

ON CABINET BASE WITH 24 QT. TILTING KETTLE

F-32484 (8-04)

MODEL: VSCX26

Regenerated Steam Convection Steamer on Cabinet Base w/ 24 Qt. Tilting Kettle

■■ VSCX26 44" wide

STANDARD FEATURES

■ Two stainless steel cooking compartments with coved interior

corners. Each compartment accepts six 1" deep, three 2

⁄2"

deep or two 4" deep 12" x 20" pans.

■ 1

⁄4" drain in each compartment.

■ Heavy duty stainless steel "slammable" doors can be opened

and closed at anytime during the cooking cycle. Steam shuts

off when door(s) are opened.

■ Tilting kettle mounted to right of cooking compartments and

interconnected to steam generator.

■ Deck mount dual temperature faucet with 12" swing spout.

■ Compartment controls include 60 minute dial timer with buzzer,

green "ready" and red "cooking" indicator lights.

■ Convection steamer mounted on 28" high base cabinet with

stainless steel front full height doors, slip-off stainless steel

side and aluminized steel rear panel with welded 6" stainless

steel legs rear with flange foot and front with bullet.

■ Direct steam supply at 40 to 50 PSI with a flow of 200 lbs.

steam/hr.

■ One year limited parts and labor warranty.

OPTIONS

■■ Stainless steel frame.

■■ Stainless steel cabinet back.

■■ Correction facility package:

a. Security type tamper resistant fasteners with tack welds.

b. Control cover with hasp (lock by others).

c. Cabinet door with hasp (lock by others).

d. Flanged feet.

■■ Step down transformer for control circuit if higher than

120 volts.

■■ Tilting kettle strainer.

■■ Second year extended limited parts and labor warranty.

ACCESSORIES:

■■ Water filter system

■■ 12" x 20" stainless steel pans:

- 1" deep (solid) (perforated) Qty._____

-2

⁄2" deep (solid) (perforated). Qty._____

- 4" deep (solid) (perforated). Qty._____

■■ Wire rack.

■■ Lift-off cover.

■■ Single perforated stainless steel basket.

■■ Contour measuring strips.

■■ Clean-up brush 20" handle with nylon brush.

■■ Pressure reducing valve.

Printed On Recycled Paper

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. 1-800-814-2028

502-778-2791 QUOTE & ORDER FAX: 1-800-444-0602

NOTE: In line with its policy to continually improve its products, Vulcan-Hart Company reserves the right to change materials and

specifications without notice.

F-32482 (8-04)

VSCX2 SERIES

REGENERATED STEAM SERIES CONVECTION STEAMER

ON CABINET BASE

DIRECT STEAM DATA:

Steam supply to the regenerated steamer must:

1. Maintain a steady 15 to 50 psi flow under operating conditions.

2. Have a minimum flow rate of 125 lbs. per hour, dry steam.

3. Be adequately trapped to provide dry steam. (See ball float trap.)

4. Provide a service shut-off valve.

WATER QUALITY STATEMENT:

The fact that a water supply is potable is no guarantee that it is suitable

for steam generation. Your water supply must be within these general

guidelines:

SUPPLY PRESSURE 20 - 80 psig

HARDNESS* less than 3 grains

SILICA less than 13 ppm

CHLORIDE less than 30 ppm

pH RANGE 7-8

* 17.1 ppm = 1 grain of hardness

Other factors affecting steam generation are iron content, amount of

chloridation and dissolved gases. Water supplies vary from state to state

and from locations within a state. Therefore it is necessary that the local

water treatment specialist be consulted before the installation of any

steam generating equipment.

SERVICE CONNECTIONS:

Steam Supply:

⁄4" NPT for 15 - 50 psi direct steam.

Electric Connection for Controls: 120/60/1, 300 watt maxi-

mum power supply with grounding wire required. (For other

than 120 volt supply, consult factory for location of this

conneciton.)

Drain: Condenser box, compartment and boiler, 2" NPT.

(Provide an open air gap type drain within 12" of condenser

box. Do not connect solidly to any drain connection.)

Cold Water Connection:

⁄8" NPT for boiler feed. Inlet water

pressure between 20 and 80 psi.

Cold Water Connection:

⁄8" NPT for condensate box. Inlet

water pressure between 20 and 80 psi.

Water: For swing faucet, (single) (dual) temperature

⁄4" IPS

tailpiece.

Steam Take-Off Connection:

⁄4" NPT.

NOTE:

• Dimensions which locate the above connections have a tolerance of

+ or -3" (+ or -77 mm).

• Installation of backflow preventers, vacuum breakers and other

specific code requirements is the responsibility of the owner and

installer. It is the responsibility of the owner and installer to comply with

local codes.

• This appliance is manufactured for commercial installation only and

is not intended for home use.

PAN CAPACITIES (Per compartment)

MODEL 1" deep 2

⁄2" deep 4" deep

VSCX2 63 2

Vulcan Hart VSCX26 Datasheet

Brand: Vulcan Hart

Model: VSCX26

Type: Datasheet

This manual is also suitable for

VSCX2

Download PDF

report

Vulcan Hart VSCX26 Datasheet

This manual is also suitable for

Vulcan Hart VSCX26 Datasheet

Related papers

Other documents