Vulcan Hart VSCX2 Datasheet

Vulcan Hart
Brand
Vulcan Hart
Model
VSCX2
Type
Datasheet

This manual is also suitable for

Vulcan Hart VSCX26 is a regenerated steam convection steamer on a cabinet base with a 24 Qt. tilting kettle. It features two stainless steel cooking compartments with coved interior corners, each of which can accommodate six 1" deep, three 2.5" deep, or two 4" deep 12" x 20" pans. The compartments have 1.25" drains, and the heavy-duty stainless steel "slammable" doors can be opened and closed during the cooking cycle without interrupting the steam supply. The tilting kettle is mounted to the right of the cooking compartments and is interconnected to the steam generator.

Vulcan Hart VSCX26 is a regenerated steam convection steamer on a cabinet base with a 24 Qt. tilting kettle. It features two stainless steel cooking compartments with coved interior corners, each of which can accommodate six 1" deep, three 2.5" deep, or two 4" deep 12" x 20" pans. The compartments have 1.25" drains, and the heavy-duty stainless steel "slammable" doors can be opened and closed during the cooking cycle without interrupting the steam supply. The tilting kettle is mounted to the right of the cooking compartments and is interconnected to the steam generator.

Item # __________________________
C.S.I. Section 11420
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. 1-800-814-2028
502-778-2791 QUOTE & ORDER FAX: 1-800-444-0602
A2780
ISO9001
Vulcan-Hart Co.
SPECIFICATIONS:
Regenerated steam generator convection steamer, Vulcan-Hart
Model No. VSCX26. Two stainless steel cooking compartments
with coved interior corners. Each compartment accepts six
1" deep, three 2
1
⁄2" deep or two 4" deep 12" x 20" pans. 1
1
⁄4" drain
in each compartment. Heavy duty stainless steel "slammable"
doors can be opened and closed at anytime during the cooking
cycle. Steam shuts off when door(s) are opened. Tilting kettle
mounted to right of cooking compartments and interconnected
to steam generator. Deck mount dual temperature faucet with
12" swing spout. Compartment controls include 60 minute dial
timer with buzzer, green "ready" and red "cooking" indicator lights.
Convection steamer mounted on 28" high base cabinet with
stainless steel front full height doors, slip-off stainless steel side
and aluminized steel rear panel with welded 6" stainless steel
legs rear with flange foot and front with bullet. Direct steam supply
at 40 to 50 PSI with a flow of 200 lbs. steam/hr.
Exterior dimensions: 44"w x 33"d x 72
1
⁄2"h.
NSF listed. Meets ASME code.
MODEL VSCX26
REGENERATED STEAM CONVECTION STEAMER
ON CABINET BASE WITH 24 QT. TILTING KETTLE
F-32484 (8-04)
MODEL: VSCX26
Regenerated Steam Convection Steamer on Cabinet Base w/ 24 Qt. Tilting Kettle
■■ VSCX26 44" wide
STANDARD FEATURES
■ Two stainless steel cooking compartments with coved interior
corners. Each compartment accepts six 1" deep, three 2
1
⁄2"
deep or two 4" deep 12" x 20" pans.
■ 1
1
⁄4" drain in each compartment.
■ Heavy duty stainless steel "slammable" doors can be opened
and closed at anytime during the cooking cycle. Steam shuts
off when door(s) are opened.
■ Tilting kettle mounted to right of cooking compartments and
interconnected to steam generator.
■ Deck mount dual temperature faucet with 12" swing spout.
■ Compartment controls include 60 minute dial timer with buzzer,
green "ready" and red "cooking" indicator lights.
■ Convection steamer mounted on 28" high base cabinet with
stainless steel front full height doors, slip-off stainless steel
side and aluminized steel rear panel with welded 6" stainless
steel legs rear with flange foot and front with bullet.
■ Direct steam supply at 40 to 50 PSI with a flow of 200 lbs.
steam/hr.
■ One year limited parts and labor warranty.
OPTIONS
■■ Stainless steel frame.
■■ Stainless steel cabinet back.
■■ Correction facility package:
a. Security type tamper resistant fasteners with tack welds.
b. Control cover with hasp (lock by others).
c. Cabinet door with hasp (lock by others).
d. Flanged feet.
■■ Step down transformer for control circuit if higher than
120 volts.
■■ Tilting kettle strainer.
■■ Second year extended limited parts and labor warranty.
ACCESSORIES:
■■ Water filter system
■■ 12" x 20" stainless steel pans:
- 1" deep (solid) (perforated) Qty._____
-2
1
⁄2" deep (solid) (perforated). Qty._____
- 4" deep (solid) (perforated). Qty._____
■■ Wire rack.
■■ Lift-off cover.
■■ Single perforated stainless steel basket.
■■ Contour measuring strips.
■■ Clean-up brush 20" handle with nylon brush.
■■ Pressure reducing valve.
Printed On Recycled Paper
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. 1-800-814-2028
502-778-2791 QUOTE & ORDER FAX: 1-800-444-0602
NOTE: In line with its policy to continually improve its products, Vulcan-Hart Company reserves the right to change materials and
specifications without notice.
F-32482 (8-04)
VSCX2 SERIES
REGENERATED STEAM SERIES CONVECTION STEAMER
ON CABINET BASE
DIRECT STEAM DATA:
Steam supply to the regenerated steamer must:
1. Maintain a steady 15 to 50 psi flow under operating conditions.
2. Have a minimum flow rate of 125 lbs. per hour, dry steam.
3. Be adequately trapped to provide dry steam. (See ball float trap.)
4. Provide a service shut-off valve.
WATER QUALITY STATEMENT:
The fact that a water supply is potable is no guarantee that it is suitable
for steam generation. Your water supply must be within these general
guidelines:
SUPPLY PRESSURE 20 - 80 psig
HARDNESS* less than 3 grains
SILICA less than 13 ppm
CHLORIDE less than 30 ppm
pH RANGE 7-8
* 17.1 ppm = 1 grain of hardness
Other factors affecting steam generation are iron content, amount of
chloridation and dissolved gases. Water supplies vary from state to state
and from locations within a state. Therefore it is necessary that the local
water treatment specialist be consulted before the installation of any
steam generating equipment.
SERVICE CONNECTIONS:
Steam Supply:
3
⁄4" NPT for 15 - 50 psi direct steam.
Electric Connection for Controls: 120/60/1, 300 watt maxi-
mum power supply with grounding wire required. (For other
than 120 volt supply, consult factory for location of this
conneciton.)
Drain: Condenser box, compartment and boiler, 2" NPT.
(Provide an open air gap type drain within 12" of condenser
box. Do not connect solidly to any drain connection.)
Cold Water Connection:
3
⁄8" NPT for boiler feed. Inlet water
pressure between 20 and 80 psi.
Cold Water Connection:
3
⁄8" NPT for condensate box. Inlet
water pressure between 20 and 80 psi.
Water: For swing faucet, (single) (dual) temperature
1
⁄4" IPS
tailpiece.
Steam Take-Off Connection:
3
⁄4" NPT.
NOTE:
• Dimensions which locate the above connections have a tolerance of
+ or -3" (+ or -77 mm).
• Installation of backflow preventers, vacuum breakers and other
specific code requirements is the responsibility of the owner and
installer. It is the responsibility of the owner and installer to comply with
local codes.
• This appliance is manufactured for commercial installation only and
is not intended for home use.
PAN CAPACITIES (Per compartment)
MODEL 1" deep 2
1
⁄2" deep 4" deep
VSCX2 63 2
  • Page 1 1
  • Page 2 2

Vulcan Hart VSCX2 Datasheet

Vulcan Hart
Brand
Vulcan Hart
Model
VSCX2
Type
Datasheet
This manual is also suitable for

Vulcan Hart VSCX26 is a regenerated steam convection steamer on a cabinet base with a 24 Qt. tilting kettle. It features two stainless steel cooking compartments with coved interior corners, each of which can accommodate six 1" deep, three 2.5" deep, or two 4" deep 12" x 20" pans. The compartments have 1.25" drains, and the heavy-duty stainless steel "slammable" doors can be opened and closed during the cooking cycle without interrupting the steam supply. The tilting kettle is mounted to the right of the cooking compartments and is interconnected to the steam generator.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents