Bosch Power Tools 1500C User manual

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Version Version française Versión en español

See page 2 Voir page 11 Ver la página 20

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

1500C

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 1

!25.$5($6$)(7<

((3:25.$5($&/($1$1':(///,7Cluttered

or dark areas invite accidents.

2 127 23(5$7( 32:(5 722/6 ,1 (;3/26,9(

$70263+(5(668&+ $6 ,1 7+( 35(6(1&( 2)

)/$00$%/( /,48,'6 *$6(6 25 '867Power

tools create sparks which may ignite the dust

or fumes.

((3 &+,/'5(1 $1'%<67$1'(56 $:$< :+,/(

23(5$7,1* $ 32:(5 722/ Distractions can

cause you to lose control.

/(&75,&$/6$)(7<

2:(5 722/ 3/8*6 0867 0$7&+ 7+( 287/(7

(9(502',)<7+(3/8*,1$1<:$<2127

86( $1< $'$37(5 3/8*6 :,7+ ($57+('

*5281'(' 32:(5 722/6 Unmodified plugs

and matching outlets will reduce risk of electric

shock.

92,'%2'<&217$&7:,7+($57+('25*5281'('

685)$&(668&+ $6 3,3(6 5$',$72565$1*(6

$1'5()5,*(5$7256There is an increased risk

of electric shock if your body is earthed or

grounded.

2127 (;326( 32:(5 722/6 725$,1 25 :(7

&21',7,216 Water entering a power tool will

increase the risk of electric shock.

2127$%86(7+(&25'(9(586(7+(&25'

)25&$55<,1*38//,1*25813/8**,1*7+(32:(5

722/((3&25'$:$<)520+($72,/6+$53

('*(625029,1*3$576Damaged or entangled

cords increase the risk of electric shock.

!+(1 23(5$7,1* $ 32:(5 722/ 287'2256

86($1(;7(16,21&25'68,7$%/()25287'225

86( Use of a cord suitable for outdoor use

reduces the risk of electric shock.

)23(5$7,1*7+(32:(5722/,1'$03/2&$7,216

,681$92,'$%/(86($5281'$8/7,5&8,7

17(55837(53527(&7('6833/<Use of

an GFCI reduce the risk of electric shock.

(5621$/6$)(7<

7$<$/(57 :$7&+:+$7<28$5( '2,1* $1'

86( &20021 6(16( :+(1 23(5$7,1* $

32:(5722/212786($32:(5722/:+,/(

<28$5(7,5('2581'(57+(,1)/8(1&(2)'58*6

$/&2+2/250(',&$7,21A moment of inattention

while operating power tools may result in

serious personal injury.

6(3(5621$/3527(&7,9((48,30(17/:$<6

:($5 (<( 3527(&7,21 Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

5(9(1781,17(17,21$/67$57,1*1685(7+(

6:,7&+ ,6 ,1 7+( 2))326,7,21 %()25(

&211(&7,1*7232:(56285&($1'25%$77(5<

3$&. 3,&.,1* 83 25 &$55<,1* 7+(722/

Carrying power tools with your finger on the

switch or energizing power tools that have the

switch on invites accidents.

(029($1<$'-867,1*.(<25:5(1&+%()25(

7851,1* 7+( 32:(5 722/ 21 A wrench or a

key left attached to a rotating part of the

power tool may result in personal injury.

212729(55($&+((33523(5)227,1*$1'

%$/$1&( $7 $// 7,0(6 This enables better

control of the power tool in unexpected

situations.

5(663523(5/<2127:($5/226(&/27+,1*

25 -(:(/5< ((3 <285 +$,5 &/27+,1* $1'

*/29(6 $:$< )520 029,1* 3$576 Loose

clothes, jewelry or long hair can be caught in

moving parts.

)'(9,&(6$5(3529,'(')257+(&211(&7,21

2)'867(;75$&7,21$1'&2//(&7,21)$&,/,7,(6

(1685(7+(6( $5( &211(&7('$1'3523(5/<

86('Use of dust collection can reduce dust-

related hazards.

2:(5722/86($1'&$5(

2 127 )25&( 7+( 32:(5 722/ 6( 7+(

&255(&732:(5 722/)25<285$33/,&$7,21The

correct power tool will do the job better and

safer at the rate for which it was designed.

212786(7+(32:(5722/,)7+(6:,7&+'2(6

127 7851 ,7 21 $1' 2)) Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

($'$//6$)(7<:$51,1*6$1'$//,16758&7,216Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

 !

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

!

WARNING

(1(5$/2:(522/$)(7<!$51,1*6

-2-

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 2

-3-

$)(7<8/(6)25+($56

2/' 32:(5 722/6 %< ,168/$7(' *5,33,1*

685)$&(6 :+(1 3(5)250,1* $1 23(5$7,21

:+(5( 7+( &877,1* 722/6 0$< &217$&7

+,''(1 :,5,1* 25 ,76 2:1 &25' Contact

with a “live” wire will make exposed metal

parts of the tool “live” and shock the

operator.

6( &/$036 25 $127+(5 35$&7,&$/ :$< 72

6(&85( $1' 6833257 7+( :25.3,(&( 72 $

67$%/(3/$7)250Holding the work by hand

or against your body leaves it unstable and

may lead to loss of control.

/:$<6 813/8* 7+( 722/ )520 7+( 32:(5

6285&( %()25( &+$1*,1* $&&(6625,(6 25

0$.,1* $1< $'-8670(176 Accidental start

up may occur causing serious personal

injury.

/:$<6 :($5 6$)(7< *2**/(6 25 (<(

3527(&7,21 /($7+(5 */29(6 $1' 6$)(7<

6+2(6 :+(1 86,1* 7+,6 722/ Shears

produce sharp metal strips or edges that if

contacted can lacerate skin easily.

!($5 ($5 3527(&7256 :+(1 86,1* 7+( 722/

)25(;7(1'('3(5,2'6 Prolonged exposure

to high intensity noise can cause hearing

loss.

6( 7+,&. &86+,21(' */29(6 $1' /,0,7 7+(

(;32685( 7,0( %< 7$.,1* )5(48(17 5(67

3(5,2'6 Vibration caused by shearing

action may be harmful to your hands and

arms.

2 127 581 7+( 722/ :+,/( &$55<,1* ,7 $7

<285 6,'( The cutters could become

entangled with clothing and injury may result.

/:$<686(7+(6833/,('+$1'*8$5'. The

guard helps keep the sharp metal strips or

pieces away from contacting your hand.

(&85(7+(0$7(5,$/%(,1*&87(9(5+2/'

60$//3,(&(6,1<285+$1'25$&5266<285

/(*6 Do not touch cutters or reach below

work or remove cut material during use of

the shear. Shears that cut metal will cut skin

easily.

527(&7 7+( &25' )520 6+$53 0(7$/ ('*(6

25675,36:+,/( 6+($5,1*0(7$/6 26,7,21

7+(&25'&/($52)527$7,1*%,7 Sharp metal

edges can pierce the jacket of the cord,

which can be a shock hazard.

2127&870$7(5,$/*5($7(57+$17+(5$7('

&$3$&,7< 2) 7+( 6+($5 Cutting material

greater than the capacity of the shear may

cause damage to the cutting edges of the

shear.

2 127 86( '8// 25 '$0$*(' &877(56 25

$&&(6625,(6 127 ,17(1'(' )25 7+,6 6+($5

(3/$&( :251 &877(56 Sharp cutters

minimize stalling.

,6&211(&77+(3/8*)5207+(32:(56285&(

$1'257+(%$77(5<3$&.)5207+(32:(5722/

%()25(0$.,1* $1<$'-8670(176&+$1*,1*

$&&(6625,(6 25 6725,1* 32:(5 722/6 Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

725(,'/( 32:(5722/62872)7+(5($&+ 2)

&+,/'5(1 $1' '2 127 $//2: 3(56216

81)$0,/,$5 :,7+ 7+( 32:(5 722/ 25 7+(6(

,16758&7,216 72 23(5$7( 7+( 32:(5 722/

Power tools are dangerous in the hands of

untrained users.

$,17$,132:(5722/6+(&.)250,6$/,*10(17

25 %,1',1* 2) 029,1* 3$576 %5($.$*( 2)

3$576 $1' $1< 27+(5 &21',7,21 7+$7 0$<

$))(&7 7+( 32:(5 722/?6 23(5$7,21 )

'$0$*(' +$9( 7+( 32:(5 722/ 5(3$,5('

%()25( 86( Many accidents are caused by

poorly maintained power tools.

((3&877,1*722/66+$53$1'&/($1Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

6(7+(32:(5722/ $&&(6625,(6$1'722/

%,76(7&,1$&&25'$1&(:,7+7+(6(,16758&7,216

7$.,1*,172$&&28177+(:25.,1*&21',7,216

$1'7+(:25.72%(3(5)250('Use of the

power tool for operations different from those

intended could result in a hazardous situation.

(59,&(

$9(<28532:(5722/6(59,&('%<$48$/,),('

5(3$,5 3(5621 86,1* 21/< ,'(17,&$/

5(3/$&(0(17 3$576 This will ensure that the

safety of the power tool is maintained.

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 3

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

212786( 21/< 5$7(' 722/6 :,7+ $

32:(56833/< While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

((3 +$1'/(6'5<&/($1 $1')5(()520 2,/

$1' *5($6( Slippery hands cannot safely

control the power tool.

(9(/23$3(5,2',&0$,17(1$1&(6&+('8/(

)25 <285722/ !+(1&/($1,1* $722/%(

&$5()8/127 72',6$66(0%/($1<3257,212)

7+( 722/ 6,1&( ,17(51$/ :,5(6 0$< %(

0,63/$&('253,1&+('256$)(7<*8$5'5(7851

635,1*6 0$< %( ,03523(5/< 02817('

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may

damage plastic parts.

Risk of injury to user. The power cord must only

be serviced by a Bosch Factory Service Center

or Autho rized Bosch Service Station.

20('867&5($7('%<32:(5

6$1',1* 6$:,1* *5,1',1*

'5,//,1* $1' 27+(5 &216758&7,21 $&7,9,7,(6

&217$,16&+(0,&$/6.12:172&$86(&$1&(5

%,57+ '()(&76 25 27+(5 5(352'8&7,9( +$50

20((;$03/(62)7+(6(&+(0,&$/6$5(

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

-4-

!

WARNING

'',7,21$/$)(7<!$51,1*6

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 4

-5-

 Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

<0%2/ $0( (6,*1$7,21;3/$1$7,21

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

.../min Revolutions or reciprocation Revolutions, strokes, surface speed,

per minute orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

I, II, III, Higher number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Li-ion RBRC seal Designates Li-ion battery recycling

program

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

<0%2/6

0

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 5

-6-

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is listed by the Canadian Standards

Association.

This symbol designates that this tool is listed by the Canadian Standards

Association, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

<0%2/6&217,18('

 Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

This symbol designates that this tool is recognized by Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters Laboratories,

to United States and Canadian Standards.

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 6

-7-

81&7,21$/(6&5,37,21$1'3(&,),&$7,216

,6&211(&7 7+( 3/8* )520 7+( 32:(5 6285&( %()25( 0$.,1* $1<

$66(0%/<$'-8670(17625&+$1*,1*$&&(6625,(6. Such preventive safety

measures reduce the risk of starting the tool accidentally.

!

WARNING

1,6+($5

>

Model number 1500C Amperage rating 4.5 A

Voltage rating 120 V 50 - 60Hz No load speed n

0

5,000/min

UPPER CUTTER

LOWER CUTTER

ATTACHMENT

SCREW

ADJUSTMENT

SCREW

STROKE ROD

ATTACHMENT

SCREW

HANDGUARD

VENTILATION

OPENINGS

SWITCH BUTTON

+($5$3$&,7,(6

$7(5,$/ $;+((7+,&.1(66

Mild Steel (60,000 PSI) up to 16 Ga. (.060")

Most Alum. (36,000 PSI) up to 14 Ga (.075")

Stainless (87,000 PSI) up to 20 Ga. (.036")

FIG. 1

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 7

-8-

3(5$7,1*16758&7,216

66(0%/<



Always unplug the tool from the power source

before changing accessories or making any

adjustments.

The upper and lower cutters and are identical,

each has four cutting edges and can be

interchanged or rotated.

When the cutting performance is

unsatisfactory, rotate each cutter 90° or

replace.

Loosen the screw of the respective cutter,

rotate the cutter 90° and re-tighten the screw.

Ensure that the lower cutter rests against the

adjustment screw.



The cutter clearance a has been

adjusted at the factory to 0.008"

and does not need to be

changed.

For working primarily with ductile, brittle or thin

sheet metal, the following values/cutter

clearance gives optimum cutting results:

Metal Metal thickness Cutter clearance $

Thin/ductile 0.012"- 0.024" 0.004"

Brittle 0.031" - 0.047" 0.010"

Brittle 0.051" - 0.063" 0.012"

Loosen screw of the lower cutter and adjust

with the adjustment screw to the required

clearance $. Check the clearance with a

gauge. Retighten the screw (Fig. 1).

The cutters must not touch

each other.

The use of any accessory or

attachment other than

recommended in this instruction manual or the

BOSCH Catalog may present a risk of personal

injury.

!

WARNING

!

CAUTION



Following a few simple tips will reduce wear

on the tool and the chance of injury to the

user.

With the tool unplugged from the power

supply and the ON/OFF Switch in the “OFF”

position, become familiar with handling the

shear and learning the location of its parts.

Secure or clamp small workpieces to be cut to

prevent slippage.

Inspect the blades for excessive wear, rotate

or replace if necessary.

Always direct the cord toward the rear, and

away from the shear. Keep it away from

sharp edges.

Never start the shear with the blades in

contact with the material being cut.

Do not exceed recommended capacities for

this shear. Premature blade failure will occur

when the shear is over-gaged.

To extend blade life and prevent corrosion,

occasional light lubrication of the blades is

recommended. Any light weight machine oil

can be used for this purpose.

!!

The tool is switched “ON” by the switch

button located at the side of the motor

housing. The switch can be locked in the

“ON” position, a convenience for long cutting

operations.

TO TURN THE TOOL “ON” without locking

it, slide the switch button forward by applying

pressure ONLY at the REAR portion of the

button. When pressure is released the switch

button will snap to “OFF” position.

TO LOCK THE SWITCH “ON”, slide the

switch button forward and press “IN” the

FRONT portion.

TO UNLOCK THE SWITCH, simply press

and release the REAR portion of the button.

Switch is spring loaded and will snap back

automatically.

Upper and Lower Cutters are the same. Reorder #2 608 635 243.

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 8

Before cutting, lightly oil the cutting line.

Hold the tool at a angle 80° to 90° to the metal

surface (Fig. 2).

Excessive feed rates reduce the performance

considerably and shorten the life of the cutters.

Sharp cutters produce good cutting results and

protects the tool.

Do not load the tool so heavily that it stalls.

Cutting curved lines: Do not tilt the tool and

work with low feed rate.

-9-

22/,36

Start the tool before applying to work and let

the tool come to full speed before contacting

the workpiece. Lift the tool from the work

before releasing the switch. DO NOT turn the

switch “ON” and “OFF” while the tool is

under load; this will greatly decrease the

switch life.



The hand guard protects the hands while

cutting, and deflects material downwards and

away from the operator. The hand guard

must be used at all times while using this

shear.

FIG. 2

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 9

-10-

(59,&(

5(9(17,9( 0$,17(1$1&(

3(5)250('%< 81$87+25,=('

3(56211(/ 0$< 5(68/7 ,1 0,63/$&,1* 2)

,17(51$/ :,5(6 $1' &20321(176 :+,&+

&28/' &$86( 6(5,286 +$=$5' We

recommend that all tool service be

performed by a Bosch Factory Service

Center or Autho rized Bosch Service Station.



Your Bosch tool has been properly lubricated

and is ready to use. It is recommended that

tools with gears be regreased with a special

gear lubricant at every brush change.



The brushes and commutator in your tool

have been engineered for many hours of

dependable service. To maintain peak

efficiency of the motor, we recommend every

two to six months the brush es be examined.

Only genuine Bosch replace ment brushes

specially designed for your tool should be

used.



After about 300-400 hours of operation, or at

every second brush change, the bearings

should be replaced at Bosch Factory Service

Center or Au thorized Bosch Service Station.

Bearings which become noisy (due to heavy

load or very abrasive material cut ting) should

be replaced at once to avoid overheating or

motor failure.

/($1,1*

2$92,'$&&,'(176$/:$<6

',6&211(&7 7+( 722/ )520

7+( 32:(5 6833/< %()25( &/($1,1* 25

3(5)250,1*$1<0$,17(1$1&(The tool may

be cleaned most effectively with compressed

dry air. /:$<6:($56$)(7<*2**/(6:+(1

&/($1,1*722/6:,7+&2035(66('$,5

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not at tempt to clean by inserting pointed

objects through openings.

(57$,1 &/($1,1* $*(176

$1' 62/9(176 '$0$*(

3/$67,& 3$576 Some of these are: gasoline,

carbon tetrachlo ride, chlo rinated cleaning

solvents, ammonia and house hold detergents

that contain ammonia.

!

WARNING

!

WARNING

$,17(1$1&(

!

CAUTION

&&(6625,(6

) $1 (;7(16,21 &25' ,6

1(&(66$5< $ &25' :,7+

$'(48$7(6,=(&21'8&72567+$7,6&$3$%/(2)

&$55<,1*7+(&855(171(&(66$5<)25<285722/

0867 %( 86(' This will prevent excessive

voltage drop, loss of power or overheating.

Grounded tools must use 3-wire extension

cords that have 3-prong plugs and receptacles.

The smaller the gauge number, the heav i -

er the cord.

#"

 

22/?6

03(5(

$7,1*

25',=(,1!

!,5(,=(6,100



3-6

6-8

8-10

10-12

12-16

18 16 16 14 0.75 0.75 1.5 2.5

18 16 14 12 0.75 1.0 2.5 4.0

16 16 14 12 1.0 2.5 4.0 —

14 12 —— ————

25 50 100 150 15 30 60 120

25'(1*7+,1((7 25'(1*7+,1(7(56

!

WARNING

* One cutter upper or lower #2 608 635 243

* Hex key 1/8" (3mm) #1 907 950 044

(*= standard equipment)

(**= optional accessories)

;7(16,2125'6

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 10

Page is loading ...

3609929809 01/11 Printed in Germany

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS

Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from

defects in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY

under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts,

without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete portable or benchtop

power tool product, transportation prepaid, to any BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH Power Tool

Service Stations, please refer to your phone directory.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW

BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME

CANADIAN PRO V INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY

FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO

STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE AND BENCHTOP ELECTRIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA,

CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL

BOSCH DEALER OR IMPORTER.

GARANTIE LIMITÉE DES OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI BOSCH

Robert Bosch Tool Corporation (le « vendeur ») garantit à l'acheteur initial seulement que tous les outils électriques portatifs et d'établi BOSCH

seront exempts de vices de matériaux ou d'exécution pendant une période d'un an depuis la date d'achat. LA SEULE OBLIGATION DU VENDEUR ET

LE SEUL RECOURS DE L’ACHETEUR sous la présente garantie limitée, et en autant que la loi le permette sous toute garantie ou condition implicite

qui en découlerait, sera l’obligation de remplacer ou réparer gratuitement les pièces défectueuses matériellement ou comme fabrication, pourvu que

lesdites défectuosités ne soient pas attribuables à un usage abusif ou à quelque réparation bricolée par quelqu’un d’autre que le vendeur ou le

personnel d’une station-service agréée. Pour présenter une réclamation en vertu de cette garantie limitée, vous devez renvoyer l'outil électrique

portatif ou d'établi complet, port payé, à tout centre de service agréé ou centre de service usine. Veuillez consulter votre annuaire téléphonique

pour les adresses.

LA PRÉSENTE GARANTIE NE S’APPLIQUE PAS AUX ACCESSOIRES TELS QUE LAMES DE SCIES CIRCULAIRES, MÈCHES DE PERCEUSES, FERS

DE TOUPIES, LAMES DE SCIES SAUTEUSES, COURROIES DE PONÇAGE, MEULES ET AUTRES ARTICLES DU GENRE.

TOUTE GARANTIE IMPLICITE SERA LIMITÉE COMME DURÉE À UN AN À COMPTER DE LA DATE D’ACHAT. CERTAINS ÉTATS AMÉRICAINS,

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION DE LA DURÉE DES GARANTIES IMPLICITES, IL

EST POSSIBLE QUE LES LIMITATIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

EN AUCUN CAS LE VENDEUR NE SAURAIT ÊTRE TENU POUR RESPONSABLE DES INCIDENTS OU DOMMAGES INDIRECTS (INCLUANT, MAIS NE

SE LIMITANT PAS AUX PERTES DE PROFITS) CONSÉCUTIFS À LA VENTE OU L’USAGE DE CE PRODUIT. CERTAINS ÉTATS AMÉRICAINS ET

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION NI L’EXCLUSION DES DOMMAGES INDIRECTS ET

CONSÉQUENTIELS, IL EST POSSIBLE QUE LES LIMITATIONS OU EXCLUSIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

LA PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS BIEN DÉTERMINÉS, Y COMPRIS POSSIBLEMENT CERTAINS DROITS VARIABLES DANS

LES DIFFÉRENTS ÉTATS AMÉRICAINS, PROVINCES CANADIENNE ET DE PAYS À PAYS.

CETTE GARANTIE LIMITÉE NE S'APPLIQUE QU'AUX OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI VENDUS AUX ÉTATS-UNIS D'AMÉRIQUE,

AU CANADA ET AU COMMONWEALTH DE PORTO RICO. POUR COUVERTURE DE GARANTIE DANS LES AUTRES PAYS, CONTACTEZ VOTRE

IMPORTATEUR OU REVENDEUR BOSCH LOCAL.

GARANTIA LIMITADA PARA HERRAMIENTAS MECANICAS PORTATILES Y PARA TABLERO DE BANCO BOSCH

Robert Bosch Tool Corporation ("el Vendedor") garantiza, únicamente al comprador original, que todas las herramientas mecánicas portátiles y

para tablero de banco BOSCH estarán libres de defectos de material o de fabricación durante un período de un año a partir de la fecha de compra.

LA UNICA OBLIGACION DEL VENDEDOR Y EL RECURSO EXCLUSIVO QUE USTED TIENE bajo esta Garantía Limitada y, hasta donde la ley lo

permita, bajo cualquier garantía o condición implícita por ley, consistirá en la reparación o sustitución sin costo de las piezas que presenten

defectos de material o de fabricación y que no hayan sido utilizadas inco rrectamente, manejadas descuidadamente o reparadas incorrectamente

por personas que no sean el Vendedor o una Estación de servicio autorizada. Para efectuar una reclamación bajo esta Garantía Limitada, usted

debe devolver el producto, que consiste en la herramienta mecánica portátil o para tablero de banco completa, con el transporte pagado, a

cualquier Centro de servicio de fábrica o Estación de servicio autorizada. Para Estaciones de servicio autorizadas de herramientas mecánicas

BOSCH, por favor, consulte el directorio telefónico.

ESTA GARANTIA LIMITADA NO SE APLICA A ARTICULOS ACCESORIOS TALES COMO HOJAS PARA SIERRAS CIRCULARES, BROCAS PARA

TALADROS, BROCAS PARA FRESADORAS, HOJAS PARA SIERRAS DE VAIVEN, CORREAS PARA LIJAR, RUEDAS DE AMOLAR Y OTROS

ARTICULOS RELACIONADOS.

TODAS LAS GARANTIAS IMPLICITAS TENDRAN UNA DURACION LIMITADA A UN AÑO A PARTIR DE LA FECHA DE COMPRA. ALGUNOS

ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LIMITACIONES EN CUANTO A LA DURACION DE UNA

GARANTIA IMPLICITA, POR LO QUE ES POSIBLE QUE LA LIMITACION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED.

EL VENDEDOR NO SERA RESPONSABLE EN NINGUN CASO DE NINGUN DAÑO INCIDENTAL O EMERGENTE (INCLUYENDO PERO NO LIMITADO

A RESPONSABILIDAD POR PERDIDA DE BENEFICIOS) QUE SE PRODUZCA COMO CONSECUENCIA DE LA VENTA O UTILIZACION DE ESTE

PRODUCTO. ALGUNOS ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LA EXCLUSION O LIMITACION DE

LOS DAÑOS INCIDENTALES O EMERGENTES, POR LO QUE ES POSIBLE QUE LA LIMITACION O EXCLUSION ANTERIOR NO SEA APLICABLE EN

EL CASO DE USTED.

ESTA GARANTIA LIMITADA LE CONFIERE A USTED DERECHOS LEGALES ESPECIFICOS Y ES POSIBLE QUE USTED TAMBIEN TENGA OTROS

DERECHOS QUE VARIAN DE ESTADO A ESTADO EN LOS EE.UU., DE PROVINCIA A PROVINCIA EN CANADA Y DE UN PAIS A OTRO.

ESTA GARANTIA LIMITADA SE APLICA SOLAMENTE A HERRAMIENTAS ELECTRICAS PORTATILES Y PARA TABLERO DE BANCO VENDIDAS EN

LOS ESTADOS UNIDOS DE AMERICA, CANADA Y EL ESTADO LIBRE ASOCIADO DE PUERTO RICO. PARA COBERTURA DE GARANTIA EN OTROS

PAISES, PONGASE EN CONTACTO CON SU DISTRIBUIDOR O IMPORTADOR LOCAL DE BOSCH.

Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A.

Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona Industrial,

Toluca, Edo. de México, C.P. 50070, Tel. (722) 2792300

BM 3609929809 01-11:BM 3609929809 01-11 1/18/12 12:28 PM Page 32

Bosch Power Tools 1500C User manual

Bosch Power Tools 1500C User manual

in other languages

Related papers

Other documents