Freedom9 80 User manual

Brand: Freedom9

Model: 80

Category: Power supply units

Type: User manual

This manual is also suitable for

freeView Power 80

freeView Power 80

8-port Power Management over IP

USER’S MANUAL

P/N: KPM-008M

Rev. 1.2

This document contains proprietary information that is protected by copyright. All rights

reserved. No part of this document may be photocopied, reproduced, or translated into another

language without express prior to written consent of Freedom9 Inc.

registered trademark of Microsoft Corporation. Other trademarks or registered trademarks are

the property of their respective holders.

freeView Power 80 User Manual  
 1
TABLE OF CONTENTS 
 
GENERAL INFORMATION..................................................................................................................2 
1 OVERVIEW......................................................................................................................................2 
2 SAFETY INSTRUCTIONS....................................................................................................................2 
3 PACKAGE CONTENTS.......................................................................................................................2 
4 FEATURES ......................................................................................................................................3 
INSTALLATION....................................................................................................................................4 
1 INSTALLATION TIPS..........................................................................................................................4 
2 NETWORK DIAGRAM........................................................................................................................4 
3 MOUNTING IN A RACK ......................................................................................................................4 
4 EXTERNAL COMPONENTS ................................................................................................................5 
5 OPTIONAL MODULES .......................................................................................................................6 
DAISY CHAINING................................................................................................................................8 
1 DAISY CHAINING .............................................................................................................................8 
MANAGING THE DEVICE.................................................................................................................10 
1 SNMPIV......................................................................................................................................10 
1.1 INSTALLING THE SOFTWARE .................................................................................................10 
1.2 USING THE SOFTWARE ........................................................................................................10 
2 WEB INTERFACE............................................................................................................................13 
2.1 MAIN MENU.........................................................................................................................13 
2.2 SYSTEM STATUS..................................................................................................................15 
2.3 RPM STATUS ......................................................................................................................16 
2.4 NETWORK...........................................................................................................................17 
2.5  SNMP................................................................................................................................19 
2.6 EMAIL .................................................................................................................................21 
2.7 PPP...................................................................................................................................22 
2.8 WEB/TELNET ......................................................................................................................23 
2.9 SYSTEM TIME......................................................................................................................23 
2.10 RPM SETTING ....................................................................................................................24 
2.11 RPM ACTION ......................................................................................................................26 
2.12 RPM SCHEDULE .................................................................................................................27 
2.13 SAVE/RESTORE SETTINGS...................................................................................................28 
2.14 EVENT LOG.........................................................................................................................28 
2.15 SAVE EVENT LOG................................................................................................................29 
3 TELNET.........................................................................................................................................29 
4 TELEPHONE ACCESS .....................................................................................................................31 
4.1 LOGGING IN.........................................................................................................................32 
4.2 MANAGING POWER PORTS ..................................................................................................32 
4.3 CHANGING THE PASSWORD..................................................................................................33 
4.4 RECOVERING THE PASSWORD..............................................................................................33 
4.5 TELEPHONE PASS-THROUGH................................................................................................33 
SPECIFICATIONS..............................................................................................................................34 
1 PRODUCT SPECIFICATIONS ............................................................................................................34 
 
 

1 General Information

1.1 Overview

The freeView Power 80 allows you to remotely control the AC power for up to eight devices

including servers, routers, modems and telephone networks. With the ability to stack up to 16

units together, up to 128 devices can be controlled from a single interface.

The freeView Power 80 supports several methods to log in remotely. The main method is to

access the unit via IP over the LAN or the internet. This method provides the user with a web-

based interface that is fast and easy to use. An alternative is to connect a modem to the unit’s

RS-232 port and access the device via dial-up modem. This method will also allow the user to

control the unit using a web interface. The last method can be used if a computer is not

available to access the freeView Power 80. Using the built-in telephone ports, the network

administrator can access the device by dialing into it from a touch-tone telephone and control it

using commands entered through the phone.

1.2 Safety Instructions

If one of the following situations arises, the equipment should be checked by service personnel.

• The power cord is damaged.

• Liquid has leaked into the equipment.

• The equipment has been exposed to excessive moisture.

• The equipment does not work properly and you can not get it to work after reading this

manual.

• The equipment has been dropped and damaged.

• The equipment shows obvious signs of damage.

1.3 Package Contents

The complete freeView Power 80 package consists of:

• freeView Power 80 unit

• AC Power Cord

• RJ-11 Daisy Chain Cable

• Eight (8) RJ-11 to RS-232 Cables

• Screws and Mounting Brackets

• User Manual and Management Software CD

Ensure that the unit was not damaged during shipping. If you encounter a problem, please

contact your dealer.

Read this manual thoroughly, and follow the installation and operation procedures carefully to

prevent any damage to the product and/or any of the devices connected to it.

freeView Power 80 User Manual

1.4 Features

The following are the main features for the freeView Power 80:

• Turn any AC powered device on or off via IP network and phone.

• Support turning on or off connected equipment manually using push buttons on the device.

• Integrated 10/100BASE-T Ethernet port for connection to a TCP/IP network.

• IP Address filtering prevent unauthorized computers from accessing the web interface

through the network.

• Supports NMS to control RPM through MIB. User also can use MIB to develop their

application interface.

• Download data and events log list to server.

• Daisy Chain expandable up to 16 units.

• When events occur, RPM can notify user by email and trap according to the pre-set

conditions.

• Allows users to configure the sequence in which power is turned on or off for each outlet.

This helps avoid in-rushes at start-up, which can cause overloaded circuits and dropped

loads. Sequencing also allows users to predetermine which piece of equipment is turned on

first so other equipment dependant on that unit will function properly.

• Customize and schedule to turn on or off the connected equipment.

2 Installation

2.1 Installation Tips

When installing the freeView Power 80, keep the following points in mind:

• Install the unit in a cool and dry place. Refer to the specifications for details on permissible

temperature and humidity ranges.

• Install the unit in a location free from electromagnetic interference, vibrations, dust, and

direct exposure to sunlight.

• Leave at least 4” (10 cm) of space at the front and rear of the unit for ventilation.

• Install the unit on a strong, sturdy surface that can support its weight, or in an EIA standard-

size rack.

2.2 Network Diagram

Figure 1 shows an example of how to install the freeView Power 80 in a network.

Figure 1 – Sample Network Diagram

2.3 Mounting in a Rack

The freeView Power 80 can be mounted in an EIA standard-size, 19-inch rack, which can be

placed in a wiring closet along with other equipment. Attach the one mounting bracket to each

side of the unit, and secure them with the screws provided.

Once the brackets are attached, align the holes in the bracket with those in the rack, and use

the screws provided to install the unit into the rack.

freeView Power 80 User Manual

2.4 External Components

The following diagrams show the front and rear panels of the freeView Power 80 (Figures 2 and

3).

Figure 2 – Front Panel

Figure 3 – Rear Panel

Phone Control Port

Connecting the freeView Power 80 to an analog telephone port will allow the device to be

controlled by dialing the telephone number associated with the phone port. The second

telephone port is used to connect an analog telephone to so calls can still be made out using

that line.

Daisy Chain Link Port

Up to 8 units can be stacked together using the provided RJ-11 daisy chain cables.

Daisy Chain LED (Yellow)

For units that are stacked together, the Daisy Chain LED indicates the ID of the current unit.

The master unit will have all LEDs off.

Power LED (Red)

The LED will be on when the receptacle is receiving power.

The LED will be off when the receptacle is not receiving power.

The LED will flash when there is a problem with the receptacle.

Manual Switches

The manual switches (A through H) are associated to the corresponding outlets in the back of

the unit. Pressing and holding the button for three seconds will toggle the state between remote

management (through the web and telnet interfaces) and local management. If a port is set to

local management, pressing the button will turn the port on or off.

Remote Control LED (Green)

The LED will be on when the receptacle is configured for remote management.

The LED will be off when the receptacle is configured for local management.

Circuit Breaker

In the event of a power surge or other disruption in the power being supplied to the device, the

circuit breaker will trip, causing the unit and all devices plugged into the unit to be turned off. If

this happens, turn off the unit and check the circuit to ensure that it is free of any shorts or other

problems which may cause another power surge before pressing the circuit breaker button and

turning the unit back on.

Communication Ports

The freeView Power 80 can instruct computers connected to the communication ports to shut

down before power is cut off to the device.

2.5 Optional Modules

The freeView Power 80 includes a freeView Power M1 module (Figure 4) which supports IP

access to the unit. The freeView Power 80 also supports the freeView Power M2 module which

supports IP access, modem access, and environment monitoring (Figure 5).

Figure 4 – freeView Power M1

Figure 5 – freeView Power M2

The following tables describe the functions of the LEDs on both modules.

freeView Power M1

LED Color Condition Description

Green Power state On: Normal power

Red Connection state with device

Flashing: Connected to

incorrect device

freeView Power 80 User Manual

freeView Power M2

Yellow Red Green Description

Off Off On Power on

Flashing On On System initializing

On Off On Normal operation

On Flashing On Connected to incorrect device

Flashing Flashing On Writing data to flash memory

LAN Port LED

LED Color Description

Green

On: LAN connection speed is 100M

Flashing: Data transmitting

Yellow

On: LAN connection speed is 10M

Flashing: Data transmitting

3 Daisy Chaining

3.1 Daisy Chaining

Up to sixteen units of the freeView Power 80 can be daisy chained to provide up to 128

managed power outlets. Each unit in the chain must be assigned a unique identification

number. The default ID is 0. The following procedure explains how to daisy chain multiple units

together:

1. Make sure that the Terminator is plugged into the first unit’s iLink port (Figure 6).

2. Plug in the first unit and turn it on.

3. Change the first unit’s ID number to “1” by logging into the web GUI, then going to the RPM

Setting menu, then selecting “01” beside “Address Change” then click “Apply” (See section

4.2.10 for details). Each unit that is configured must have its own unique ID, (the default ID

is "0"). After changing the unit’s ID number, you will see the LED beside the number 1 light

up on the front panel of the first unit.

Figure 6 – First Unit with Terminator in leftmost iLink Port

4. Make sure that the Terminator is plugged into the second unit’s iLink port (Figure 7).

5. Remove the Ethernet module from the second unit.

6. Connect the first and second RPM together with an iLink cable.

7. Plug in the second unit and turn it on.

8. Configure the second unit’s ID number to “2” by logging into the web GUI, going to the RPM

Setting menu, select “RPM00” under Select RPM, then select “02” beside “Address Change”

then click “Apply”. After changing the unit’s ID number, you will see the LED beside the

number 2 light up on the front panel of the second unit.

Figure 7 – First and Second Unit Connected with iLink Cable

9. For configurations with two units, the setup is now complete. For configurations with more

units, proceed with the following steps.

10. Remove the Terminator for the second unit.

11. Make sure that the Terminator is plugged into the third unit’s iLink port (Figure 8).

12. Remove the Ethernet module from the third unit.

13. Connect the second and third RPM together with an iLink cable.

14. Plug in the third unit and turn it on.

freeView Power 80 User Manual

15. Configure the third unit’s ID number to “3” by logging into the web GUI, going to the RPM

Setting menu, select “RPM00” under Select RPM, then select “03” beside “Address Change”

then click “Apply”. After changing the unit’s ID number, you will see the LED beside the

number 3 light up on the front panel of the third unit.

Figure 8 - First Three Units Connected with iLink Cable

For configurations with more than three units, repeat steps 10-15 for the remaining units.

4 Managing the Device

4.1 SNMPIV

The included SNMPIV software allows you to perform maintenance on the device even if you do

not know the IP address of the unit. The SNMPIV software also includes a standard MIB which

allows the unit to be monitored with third-party network management software.

4.1.1 Installing the Software

To install the software, follow these steps:

1. Insert the CD included in the box in your CD-ROM drive.

2. Open Windows Explorer and browse to the CD-ROM drive.

3. Double-click on the file “SNMP Utility.exe”.

4. Follow the instructions displayed on the screen to install the software.

5. After completing the installation, the software can be started by going to Start Menu Æ All

Programs Æ SNMP Utility Æ SNMP Utility (Figure 9).

Figure 9 – Windows Start Menu

4.1.2 Using the Software

The menu is located on the left side of the window. The table on the right side of the window

shows all freeView Power 80 devices on the network (Figure 10).

Figure 10 – SNMP Utility

Network Selection

When the software first starts, it will prompt you to select the network interface to use. To

change the network interface to use, click “Network Selection” to display a list of available

network interfaces (Figure 11), and select the one to use. All devices must be on the same

network as the computer in order to be detected by the software.

freeView Power 80 User Manual

Figure 11 – Network Selection

Network Selection

By default, the software will automatically select a network interface card to use (wired or

wireless). To change the network interface to use, click “Network Selection” to display a list of

available network interfaces (Figure 11), and select the one to use. All devices must be on the

same network as the computer in order to be detected by the software.

Configure

The “Configure” button allows you to configure a freeView Power 80 unit selected from the list

on the right side of the window. The first tab to be displayed is the “IP Address” tab (Figure 12).

On this tab, you can set the IP address of the device dynamically using DHCP, given through

BOOTP, or statically by manually entering the information in the window.

Figure 12 – IP Address Tab

After setting the IP address of the device, you can access the web interface or telnet interface of

the unit from any computer on the same network as the device.

The second tab is the “Advanced” tab (Figure 13). This tab allows you to set a password for

accessing the freeView Power 80 device from the SNMPIV software (this does not affect the

web or telnet interface passwords). To set a password, enter the password into the “New

password” field, and enter it again in the “Confirm password” field, and click “OK”. Remember to

keep a record of this password, as it cannot be recovered if lost.

Figure 13 – Advanced Tab

On this tab, you can also set the ports used by the device for HTTP (web) and telnet access.

You can also disable web and/or telnet access altogether by unchecking the boxes next to the

applicable interface. If you change a port from the default port, you will have to enter the full IP

address and port in order to access to the device. For example, if you change the HTTP port

from 80 to 81, you must enter “http://192.168.0.5:81” to access the web interface of the device.

Download Firmware

The software offers a convenient method of upgrading the firmware on a device. To upgrade

the firmware on a device, select the device from the list, and click “Download Firmware”. In the

new window (Figure 14), enter the path and name of the firmware file or click “…” to browse for

the file. The file should end in “.bin”. Click “Start”. During the upgrade, the freeView Power 80’s

Red and Yellow LED will flash alternately. After the upgrade has been completed, the unit will

reboot automatically.

Note: In the event the firmware upgrade is interrupted (e.g. due to a power

failure), the unit will revert to the old firmware version. Performing the upgrade

again will load the new firmware onto the unit.

Figure 14 – Firmware Download

freeView Power 80 User Manual

Refresh

Click the “Refresh” button to search the network for freeView Power 80 devices.

4.2 Web Interface

To access the web interface of the freeView Power 80, follow these steps:

1. Open a web browser (Internet Explorer 6.0 or higher is recommended).

2. Enter the IP address of the unit into the address bar (e.g. “http://192.168.0.5”)

3. On the login screen, enter the user name and password (Figure 15). By default, both fields

are blank. It is recommended that you change the user name and password as soon as

possible for security reasons.

Figure 15 – Login Window

4.2.1 Main Menu

The main menu consists of four categories (Figure 16).

Figure 16 – Main Menu

Information: Provides information for the connected devices.

Configuration: Allows for configuration of the network and devices settings.

Log Information: Displays the log of events that occurred on the device.

Device selection: Not currently used.

Each category consists of different pages which are described in detail in the following sections.

freeView Power 80 User Manual

4.2.2 System Status

The System Status page (Figure 17) displays the details of the system along with current

network configuration settings.

Figure 17 – System Status Page

Firmware Version: Current version of firmware on the unit.

Device Number: Unique identifier for the unit.

System Name: The name given to the unit for identification purposes – used with SNMP.

System Contact: The name of the person to contact in case there are problems with the unit –

used with SNMP.

Location: The location of the unit – used with SNMP.

System Time: The local time on the device.

Uptime: The amount of time the unit has been running.

MAC Address: The MAC address of the unit.

The remaining items will be explained in the following sections.

4.2.3 RPM Status

The RPM Status page (Figure 18) displays the current status of all of the power outlets, and

allows you to turn outlets on and off.

Figure 18 – RPM Status Page

If a power outlet is off, clicking on the icon to the right of the outlet will turn it on. If a power outlet

is on, clicking on the icon to the right of the outlet will turn it off. Clicking the icon beside “All On”

will turn all of the outlets on. Clicking the icon beside “All Off” will turn all of the outlets off.

Outlets labeled as “non-internet” cannot be controlled from the web interface and will not be

affected by the “All On” and “All Off” buttons.

If there are multiple units in a stack, select the unit to control under “Select RPM”. The yellow

LED on the front panel of the device indicates its ID number in the stack.

freeView Power 80 User Manual

4.2.4 Network

The Network page (Figure 19) allows you to change the network settings of the device.

Figure 19 – Network Page

IP Address: The IP address of the unit used for web and telnet access.

Subnet Mask: The subnet mask of the unit.

Gateway: The gateway of the unit, required for accessing external mail servers for email

notifications.

Obtain an IP Address: Select whether the unit uses the IP address entered manually in the

fields above, or obtains an IP address from a DHCP server.

Primary DNS Server: The primary DNS server used for name resolution.

Secondary DNS Server: The backup DNS server used for name resolution in the event the

primary DNS server is unavailable.

Connection Type: Determine the connection speed and duplex of the Ethernet port (Auso

Sense, 10Mbps Half-Duplex, 10Mbps Full-Duplex, 100Mbps Half-Duplex, 100Mbps Full-

Duplex). The recommended settings is “Auto Sense”.

Services Provider: The dynamic DNS service provider used (None, 3322.org, dhs.org,

dyndns.org, myddns.com).

Domain Name: Your registered DDNS domain name.

Use External STUN server to get Public IP to register: Set whether a STUN server should be

used to retrieve the public IP address of the device.

Primary STUN Server IP: If a STUN server is used, this is the primary IP address of the STUN

server.

Secondary STUN Server IP: If a STUN server is used, this is the secondary IP address of the

STUN server in the event the primary server is unavailable.

When Connection should be made: Determine when the unit should connect to a PPPoE

internet connection (Disabled, Connect Always).

Page is loading ...

Freedom9 80 User manual

Brand: Freedom9

Model: 80

Category: Power supply units

Type: User manual

This manual is also suitable for

freeView Power 80

Download PDF

report

Freedom9 80 User manual

This manual is also suitable for

Freedom9 80 User manual

Related papers

Other documents