nComputing L130 User manual

Category
Laminators
Type
User manual

This manual is also suitable for

www.ncomputing.com
L130, L230 and L300
Ethernet Virtual Desktops
with vSpace
User Manual
L300/L230/L130 User Manual
2
Important Notices
Please note that reproduction of this User Guide in whole or in part, without express written permission from
NComputing, is not permitted.
NComputing reserves the right to make improvements and/or changes to this User Guide and to the products,
programs and/or specifications described herein at anytime without notice. Information contained in this
document may have been obtained from internal testing or from a third party. NComputing shall not be liable
for any direct, indirect, special, incidental or consequential damages in connection with the use of this material.
The latest version of this User Guide can be downloaded from the “Documentation page in the support section
of the NComputing website at: www.ncomputing.com
Refer to the Limited Hardware Warranty applicable to your region for information on what is and what is not
covered by the warranty, your responsibilities, exclusions, and how to obtain service. It is your responsibility
to download a copy of the warranty at the time of purchase to keep for your records. The warranty can be
downloaded from the “Documentation page in the support section of the NComputing website.
Please refer to the End User License Agreement (EULA) and Terms of Use (TOU) that are presented for your
review during the software installation process. The information contained in these documents is very
important. The EULA and TOU constitute agreements between you and NComputing and are accepted by
you by installing and using the product. It is your responsibility to print a copy of the EULA and TOU directly
from the installer in order to keep for your records.
This product gives users shared access to computer resources. It is not a computer, and may not support all
software applications, especially high-resolution graphics applications or 3D games that are designed to be
supported by stand-alone computers. Similarly, it may not support all hardware peripherals that are designed
to be supported by stand-alone computers.
Refer to your computer operating system and application software vendors’ license agreements for information
on using these products with NComputing systems. Additional software licenses may be required.
Microsoft® Windows® Licenses. You are licensed by NComputing to use the vSpace software under the
terms of the EULA. You must also acquire the appropriate number of Windows Server licenses and Client
Access Licenses for each device or user accessing Windows Server software. You cannot use the vSpace
software with Windows Client software (i.e., Windows Vista, Windows 7) unless a single user and no other
user accesses the same Windows Client software at any one time, or you are authorized to do so under an
applicable license from Microsoft or as expressly set forth in the “Microsoft Windows Server to Windows XP
License Rights” section of the NComputing EULA. In all cases, your rights and obligations with respect to the
use of vSpace software with Windows Server software and Windows Client software are defined by both the
NComputing vSpace software EULA and the applicable Microsoft Software License Agreement or EULA. For
more information on licensing with Microsoft operating systems see: www.ncomputing.com/mslicensing
For single user applications of your L-series product such as remote control, digital signage and 1:1 VDI refer
to the same web page for information on client operating systems currently supported.
The NComputing hardware and software products described in this user manual are protected by numerous
granted and pending U.S. and international patents.
© 2003-2010 NComputing Inc. All rights reserved. NComputing, vSpace, and Numo are registered trademarks of
NComputing Inc. USA. Microsoft, Windows, Windows Media, and DirectShow are registered trademarks of Microsoft
Corporation. Intel, Core 2, Core i5, and Core i7 are registered trademarks of Intel Corporation. KCC is a trademark of
KCC Corporation. Matroska is a trademark of CoreCodec, Inc. VESA is a trademark of Video Electronics Standards
Association. Kensington is a trademark of ACCO World Corporation. QuickTime is a registered trademark of Apple,
Inc. DivX is a registered trademark of DivX, Inc. Youtube is a registered trademark of Google. Adobe and Adobe Flash
are registered trademarks of Adobe Systems, Inc. All trademarks are the property of their respective owners.
L300/L230/L130 User Manual
3
TABLE OF CONTENTS
Safety Information 4
Regulatory Compliance 4
Product Overview 6
Installation 8
vSpace software installation 8
L300 Device Setup 12
Product Registration 14
Online Registration 14
Offline Registration 16
Add Additional vSpace License 18
Completing the Offline Registration Process 18
Updating the vSpace Software 19
Uninstallation 19
Using Your L-series Access Device 20
L130/L230 Access Devices 20
L300 Access Devices 25
L300 Multimedia Acceleration 32
Using the vSpace Management Console 32
Software Settings (local) 37
Software Settings (LAN) 43
Hardware Settings (LAN/local) 44
Troubleshooting error messages 47
Glossary 50
FAQ 52
L300/L230/L130 User Manual
4
Safety Information
Refer to the following to prevent any physical injury or loss of assets caused by damage to the product.
A user must read this User Manual carefully before use and properly follow the instructions.
Make sure that the place of installation is not too hot (above 35˚C), too cold (below 0˚C), or too wet
(above 85% relative humidity).
Avoid any severe impacts to the product
Make sure that the product is not exposed to direct sunlight or any hot machinery.
Please keep the product away from any items which have strong magnetic properties.
Do not disassemble, repair or rebuild the product.
Please properly route all cables and power cords to avoid a tripping hazard. An electric shock, fire,
damage to the product or physical injury may occur as a result of tripping over the cable.
Regulatory Compliance
FCC Information
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try and correct the interference by one or the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to a power outlet on a circuit different from which the receiver is
connected
Consult your dealer or an experienced radio TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
L300/L230/L130 User Manual
5
전자파적합등록 (EMC Registration)
European Community:
Disposal Information:
This symbol means that according to local laws and regulations your product should be disposed of separately
from household waste. The separate recycling of your product will help ensure that it is recycled in a manner
that protects human health and the environment.
기기의 명칭(모델명) : Multi-User Computing Access Device
(L230)
인증 번호 : NCC-L230 (B)
인증 받은 자의 상호 : 엔컴퓨팅 주식회사
제조자/제조국가 : 엔컴퓨팅 주식회사/한국
제조년월 : 제품 뒷면 참고
NCC-L230 (B)
기기의 명칭(모델명) : Multi-User Computing Access Device
(L130)
인증 번호 : NCC-L130 (B)
인증 받은 자의 상호 : 엔컴퓨팅 주식회사
제조자/제조국가 : 엔컴퓨팅 주식회사/한국
제조년월 : 제품 뒷면 참고
NCC-L130 (B)
기기는 가정용으로 전자파 적합 등록을 기기로서 주거지역에서는 물론 모든
지역에서 사용할 있습니다.
기기의 명칭(모델명) : Network virtual desktop (L300)
인증 번호 : NCC-L300 (B)
인증 받은 자의 상호 : 엔컴퓨팅 주식회사
제조자/제조국가 : 엔컴퓨팅 주식회사/한국
제조년월 : 제품 뒷면 참고
NCC-L300 (B)
L300/L230/L130 User Manual
6
Product Overview
The NComputing L-series access devices with vSpace™ desktop virtualization software dramatically cut your
computing costs by enabling up to 30 users to share a single PC, server or virtual machine. Each user gets
their own virtual desktop with a rich, multimedia computing experience that is practically indistinguishable from
running on a full PC. Best of all, IT staff and end users do not need special training because this end-to-end
solution is easy to manage and is compatible with standard desktop applications.
Product Comparison
This user manual covers three distinct L-series products: L130, L230 and L300. The entry-level L130
provides all of the basic features needed for a good virtual desktop experience, complete with keyboard,
mouse, monitor and speaker connections. The L230 adds a USB port for connecting storage devices, a
microphone port, and more color depth for an even better user experience. The L300 delivers the best
possible virtual desktop experience with the addition of a high-performance video acceleration system that
supports full screen motion video, higher screen resolutions and more USB peripheral ports. The following
table summarizes the key differences between the products in the L-series family.
L130
L230
Maximum Screen Resolution (Wide)
1440x900
1440x900
Maximum Screen Resolution
(Standard)
1280x1024
1280x1024
Maximum Color Depth
16-bit
24-bit
Mouse & Keyboard Ports
PS/2
PS/2
Speaker Port
Yes
Yes
Microphone Port
No
Yes
USB Peripheral Ports
None
1 x USB 1.1*
Video acceleration for full-screen
video support
No
No
*NComputing L-series access devices use remote USB 1.1 or 2.0 to provide transparent USB redirection.
L300/L230/L130 User Manual
7
System Requirements
The minimum recommended system specifications for a vSpace installation can be very minimal. The host PC
may only need 1-2 GB of memory, a 2.4 GHz single-core processor, and less than 100 MB of free hard drive
space to run a few users. However the number of users, intended application suite and overall performance
expectation will ultimately determine how powerful a computer must be in order to deliver the desired multi-
user experience.
Note: It is not advised to use a notebook PC as the host. Notebooks use power-saving features and technologies different
than a typical desktop PC. This may cause power management and memory incompatibilities.
Minimum Host Hardware Configuration (L130 or L230)
Host Configurations
Number of Users
1-3
4-7
8-10
10-20
20-30
Most
Applications
CPU* (minimum or
Equivalent)
2.4 GHz or
Dual Core
3.0 GHz or
Dual Core
Dual Core
Fast
Dual
Core
Fast Dual
or Quad
Core
Host Memory
1-2 GB
2 GB
3 GB
3-4 GB
4 GB
* CPU recommendations are for Pentium class of processor or newer
The table below gives recommended specifications for a vSpace host computer, based on number of users
and the type of applications used. NComputing recommends you test your environment in advance of
deployment to ensure it meets your expectations.
Recommended Host Hardware Configuration (L300)
Host Configurations
Number of Users*
1-3
4-7
8-10
10-20
20-30
Productivity
Applications
CPU** (minimum or
Equivalent)
Core 2
Core 2
Core 2
Core i5
Core i7
Host Memory
2 GB
3 GB
3 GB
4 GB
4 GB
Multimedia
Applications
CPU** (minimum or
Equivalent)
Core 2
Core i5
Core i7
Core i7
Core i7
Host Memory
2 GB
3 GB
3 GB
4 GB
4 GB
* For the L-Series access terminal, the maximum number of users is 30. The number of users a customer's installation will
support depends upon the host's configuration and performance expectations of the customer. Performance results are highly
dependent upon the individual host hardware, memory, video card, applications being used, OS and network conditions within
any LAN/WAN. Host requirements will vary, please test your multi-user environment before deployment. For more information
on supporting multiple simultaneous multimedia streams see the document "Configuring an L300 Multiuser Environment".
** CPU recommendations are generation of processor or equivalent
Note: This table is only a guideline; actual use may vary based on system utilization.
L300/L230/L130 User Manual
8
For Microsoft OS licensing information see the paragraph on page 2.
For each L-series device you will need:
Keyboard and mouse (PS/2 for L130/L230 or USB for L300)
Monitor
A category 5/6 network cable to connect to your existing Ethernet network
Optional: speakers, headphones, microphones and USB peripherals
Installation
vSpace software installation
Insert the software installation CD into the host
computer's CD drive. In most cases, a
window will automatically appear after a few
seconds with installation options. If it does not
appear, go to "My Computer," open the CD
drive's icon, and start the "Setup" application.
At the initial setup screen, click the "Download
Latest Software" button. This will launch a
browser window at the NComputing Software
Download Center, Locate the correct software
based on product model and operating system,
and download the corresponding “zip” folder.
(Note the current version of vSpace is always
located at www.ncomputing.com/downloads)
If internet access is unavailable, click “Browse CD” to locate the installer file per the next step
After downloading and extracting the installer files, or alternately locating them on the product CD, run
the vSpace Installer MSI.
Note: If the MSI file is not present, instead run “setupnc.exe”
At the installer’s "Welcome" screen, click on the "Next" button.
At the antivirus and firewall warning screen, read and follow the instructions, then click on the "Next"
button.
L300/L230/L130 User Manual
9
At the software End User License Agreement screen, please read the agreement. When you are
finished, if you agree, click on the "I agree" checkbox, and then click on the "Next" button.
At the software Terms of Use screen, please read the terms of use. When you are finished, if you
agree, click on the "I agree" checkbox, and then click on the "Next" button.
At the “Additional Options” screen, you may choose to install the Network Administrator Console, which
expands vSpace’s control capabilities, so that multiple host PCs may be administered from one
location. If you choose to use an administrator password, enter it and retype it. Click on the "Next"
button.
At the "Choose destination location" screen, you can install to the default location, or you can choose a
different location. When you are finished, click on the "Next" button.
At the final “Confirm Installation” screen, click “Install” to begin the software installation. This process
may take up to 5 minutes to complete, and it is normal for the system to beep frequently. The installer
may appear to freeze or cause a lock-up, but if the mouse cursor regularly switches between the
pointer and the hourglass, everything should be proceeding normally. If the installer takes longer than
15 minutes to complete, please contact NComputing technical support for assistance.
At the "vSpace successfully installed" screen, click “Close to end the installer, and select whether or
not to immediately restart the computer (a restart is required before vSpace can be used).
Note: When dealing with certain firewall applications, you may need to make sure that the
NComputing .exe files have proper access permission to the network. These .exe files include:
KMSERVC.EXE, BOOTSRV.EXE, KMMSG.EXE, KMUPDATE.EXE, KMREGWIZ.EXE
Within the Exceptions tab of the Windows Firewall the ports that should be opened are:
TCP-Protocol: 27605, 27615, 3581, 3597, 3645, 3646, 3725
UDP-Protocol: 1027, 1283, 3581, 3725
Please see our Knowledge Base at http://www.ncomputing.com/support.aspx for more details.
L300/L230/L130 User Manual
10
L130 and L230 Device Setup
(For L300 devices, see next section)
The access device must be connected via Ethernet to the host PC. This can be done using an Ethernet switch,
a router, or some other network connection method.
Network connection
If the network is configured to use DHCP to get dynamic IP addresses, you can setup the access device to use
it. Turn on the access devices and once you see the main screen select the "Options" button, and then select
the “Setup” button.
In the "Network" tab, select whether to use a dynamic IP address or a static IP address.
L300/L230/L130 User Manual
11
If you choose to use a dynamic IP address, click on the "Save" button.
If you choose to use a static IP address, you must enter the IP address and the default gateway. Then click on
the "Save" button.
Installation with monitor mount
The L130 and L230 products include a monitor mount, mounting collar, monitor mount screws (silver color) and
mounting collar screws (black color) for mounting it to the back of a monitor.
These pictures show the L230 mounting process, and the final product, fully mounted and ready for use.
L300/L230/L130 User Manual
12
L300 Device Setup
The L300 must be connected to the host PC via an Ethernet switch, router, or other network connection. The
L300 has USB ports dedicated for mice and keyboards, as indicated by the mouse and keyboard symbols
below the horizontally oriented USB ports. The vertically oriented USB ports to the left of the audio
connections are for other USB devices.
Network connection
The L300 device can be configured to use DHCP-assigned network settings, or use settings specified by the
user. To use DHCP-assigned settings, power on the device, then go into the Device Setup, click the
“Network” tab, and select the bullet labeled “DHCP.
NOTE: The USB keyboard and mouse ports ONLY support these types of devices. No other types of
USB devices are supported on these ports. The USB keyboard and USB mouse must be directly
connected to these ports and cannot go through a separate USB hub. Peripherals with integrated USB
hubs or combination keyboard/mouse devices are not supported by these ports. Other USB peripherals
can be connected to the vertically oriented ports that are to the left of the audio ports note that these
generic ports are not active until you have connected to a vSpace session.
L300/L230/L130 User Manual
13
If static addressing configurations are used on the network, select “Static configuration” and supply the
appropriate IP, Subnet Mask, Gateway, and DNS server (primary and alternate) information. Click “OK” to
save changes and return to the Server Selection screen.
When your L300 device is connected to the network the “LNK” light (indicating Ethernet link) on the L300 front
panel should be on and you should see that the Ethernet activity light, “ACT,” also blinks when there is active
Ethernet traffic to/from the device.
Installation with monitor mount
The L300 device comes with a mounting plate and two mounting screws, which can be secured to a monitor
via 75mm or 100mm VESA-compliant mounting holes. The L300 device then attaches to the mounting
plate, resulting in a zero-footprint workstation. In general, we recommend using the top two mounting holes
on the monitor to give maximum cable access space.
Note: The L300 product also comes with a Kensington security lock interface, for additional theft protection.
L300/L230/L130 User Manual
14
Product Registration
Product registration is required for all L-series devices and
vSpace software to enable normal product use,
downloading updates, and technical support. Prior to
registering, sessions will time out after one hour and
devices will not be able to connect after 30 days. When
registering the software, all the access devices must be
connected to the host PC using Ethernet.
Select "vSpace Registration" in the Windows Start menu.
At any time during the registration process, click on the
"Cancel" button and the process will be cancelled, or use
the "Back" button to return to previous screens in the
registration process and modify entries.
At the registration program “welcome” screen, if
vSpace password protection is turned on, you will
need to enter your password. Then click the "Next"
button.
Next, you are presented with the vSpace End User
License Agreement (EULA). If you agree, click in
the “I agree” check box, and then click the “Next”
button.
Online Registration
In the case of Online Registration, follow the instructions below. Otherwise skip to the section titled “Offline
Registration.
If you want to register your software and L-series access devices online, leave the “Register” radio
button selected, and click “Next.
IMPORTANT NOTICE!
DEVICE AND VSPACE SOFTWARE REGISTRATION ARE REQUIRED.
UNTIL YOU HAVE REGISTERED, SESSIONS WILL TIME OUT AND DISCONNECT AFTER 1 HOUR.
YOU HAVE 30 DAYS AFTER THE INITIAL INSTALLATION TO REGISTER. IF YOU DO NOT
REGISTER WITHIN 30 DAYS, DEVICES WILL NOT BE ABLE TO CONNECT TO THE HOST. IF
THE 30 DAY LIMIT IS REACHED YOU CAN STILL ACCESS THE REGISTRATION WIZARD ON THE
HOST TO COMPLETE REGISTRATION.
L300/L230/L130 User Manual
15
At the "Customer Data" screen, if the data fields are not already populated, enter the registered user's
relevant information. Each field in this window must be filled in. Once all data has been entered, click
on the "Next" button.
Select “Register online, using your internet connection” and click “Next.”
Note: If you use a Proxy Server for internet connectivity, enter the Proxy connection data here.
The registration wizard will then show you a list of all unregistered L-series access devices that are
currently connected to this vSpace host. You cannot select which devices will be registered all
devices shown in this list will be registered.
Before the registration wizard communicates with the registration server, you will get the following
“Summary” screen showing all user information that will be registered with the vSpace software. Also,
any connected but unregistered L-series access devices will be listed for registration. If the data is
correct, click on the “Register” button to initiate the registration or click “Back” if you wish to change any
of the information.
When your registration is complete, you see the “Registration results” screen. Be sure to click the
check box for the “Register future L-series devices in the background option, if you want vSpace to
automatically register any unregistered L-series access devices that connect to this system in the
future. Use of this “background registration” feature requires standard internet connectivity.
L300/L230/L130 User Manual
16
Offline Registration
In the case of Offline Registration, follow the instructions below. If you have completed the online registration
section, skip to “Using the access device”.
If you don’t have standard internet connectivity, you can use standard email to register your vSpace
software and L-series access devices.
To use offline registration, you again select the Register” option, and click “Next.
At the "Customer Data" screen, if the data fields are not already populated, enter the registered user's
relevant information. Each field in this window must be filled in. Once all data has been entered, click
on the "Next" button.
The registration wizard will then show you a list of all unregistered L-series access devices that are
currently connected to this vSpace host. You cannot select which devices will be registered all
devices shown in this list will be registered.
On the next screen you then select the “Create off line registration file” option and click “Next.”
L300/L230/L130 User Manual
17
You’ll need to select the location where you wish to store the registration data file that you’ll later email
to NComputing. Note that you cannot type directly into the “Create activation file” field, but you must
click on the “Select” button to navigate to the directory where you wish to store the offline registration
data file.
The window below shows the navigation screen that allows you to place the data file in the desired
location. Feel free to change the “File name” to something other than “activation” – but don’t change
the “Save as type” field. The registration file must be of type “txt” – even though the data inside is
encrypted and must not be modified.
Before the registration wizard writes the data file, you will get a “Summary” screen showing all user
information that will be written to the data file. Also, any connected but unregistered L-series access
devices will be listed for registration.
If the data is correct, click on the “Register” button or click “Back” if you wish to change any of the
information.
Next, email the created “txt” file to registration@ncomputing.com. Alternately, you can copy the “txt”
file to another PC, if necessary, to send the email.
L300/L230/L130 User Manual
18
Add Additional vSpace License
The second option on the “Type of Registration” screen is a feature reserved for future use in extending
vSpace software capabilities by adding additional or optional vSpace licenses.
Completing the Offline Registration Process
It should normally take only one or two minutes to receive the vSpace license file by returned e-mail.
When you receive the license file, save it in a convenient disk location, and restart the “Registration Wizard,
Select the “Complete offline registration by using activation file” option and click “Next and navigate to the disk
directory where you have stored the returned license/activation file.
Click “Select” to do the navigation, and click “Open” once you have located the correct license file. Then click
“Next” to load the license file and apply it to the vSpace host system.
L300/L230/L130 User Manual
19
After the offline file is loaded, you see the “Registration results” screen. Click the “Next” button to complete
the offline registration process. Your devices are now registered and ready for continuous use.
Updating the vSpace Software
Once you have successfully completed the registration process,
you can update the vSpace software directly over the Internet by
selecting “vSpace Update” from the Start Menu.
Note: If the “Enter Password” window appears, enter the vSpace administrator
password you selected during vSpace installation.
Click the “Connect” button to check for a software update. If there
is a new version available, click on the “Download” button to start
the update process. If there is no new version available, click on
the “Exit” button. When the download is complete, the installation
of the new version will begin.
Alternately, the latest NComputing software can be obtained from
http://www.ncomputing.com/downloads.
Uninstallation
To uninstall the vSpace program, select “Uninstall vSpace” under the “NComputing vSpace” folder in the Start
Menu (or select vSpace from the Add/Remove Programs utility in the Windows Control Panel). Follow the
uninstall utility’s prompts to remove the program components. After the programs are uninstalled, you must
restart the host PC to complete removal process.
L300/L230/L130 User Manual
20
Using Your L-series Access Device
L130/L230 Access Devices
(For L300 devices, see next section)
The available connection list shows the vSpace hosts to which the device can connect. Select a host from the
list and click on the "Connect" button to start.
The "Refresh" button refreshes the available connection list.
The Options Menu
The "Options" button brings up a menu where you can view and change the access device's settings.
Within the “Options” screen, the "Reset" button resets the access device
The "Info" button brings up a window to view the following information about the access device:
Version: the version of firmware running on the access device
Build: The build number of the firmware running on the access device
Date: The date of the firmware running on the access device
Device Model: The model number of the access device
Loaded Schema Version: The schema version running on the access device
IP Address: The IP address the access device is configured to use
Gateway: The IP gateway the access device is configured to use
MAC Address: The MAC address of the access device
Serial Number: The serial number of the access device
Alias: The alias of the access device, defined using the vSpace admin console
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53

nComputing L130 User manual

Category
Laminators
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI