2. REDLINE
  3. Ford F150
Ford F150

REDLINE Ford F150 User guide

  • Hello! I've reviewed the user manual for the OPT7 Redline Quick Connect Expansion Adapter Harness. This document provides instructions on installing the harness in 2015-2020 Ford F150 models and includes important installation steps, wiring information and safety recommendations. I'm ready to answer your questions about this product.
  • What vehicles is this adapter harness compatible with?
    Does this harness require cutting or splicing of factory wires?
    What type of connector is used for trailer lights?
Expansion
Adapter
Redline
FOR FORD F150 ALL MODELS
WITH BLIS/BACKUP CAMERA/ASSIST SENSOR
Hello Fellow OPT7-ites, Introducing the Redline Quick Connect Harness to Flat
4-Pin Extension Adapter Harness
The OPT7 Redline Quick Connect Expansion Adapter Harness is purpose-built to
be used as a trailer accessory for 15-20 F150 all models. It provides a
plug-and-play style that allows you to quickly, seamlessly and virtually hidden
installation without cutting or splicing your factory harnesses.
3.94”
3.94”
110.23”
70.87”
2015-2020
Installation
Open up your tailgate first.
Next, locate the two bolts that
lock the tail light (See Figure 1)
and loosen them.
Slowly move the loose tail light
until it is completely removed(See
Figure 2).
There are two plastic clips on
the inside of the tail light for
fixing, please be careful not to
break it when removing it.
Step 1Step 1
Locate the OEM wiring harness
(See Figure 3) and unplug it from
the tail light assembly by lightly
pressing the Release-Latch on the
connector.
Important
Figure 1Figure 1
Step 2Step 2
Figure 2Figure 2
Step 3Step 3
Figure 3Figure 3
Tail light
Connector
Tail light
Connector
OEM Wiring
Harness
OEM Wiring
Harness
To make it easier for you to identify the signal location represented by the
Connector/Wiring. Please read the relevant wiring instructions carefully
before commencing any work.(See Figure 4)
OEM TAIL LIGHTS
White = Reverse
White
Brown
Yellow
Green
=
=
=
=
Ground
Tail Lights
Left Turn & Brake
Right Turn & Brake
RIGHT
Passenger Side
LEFT
Driver’s Side
HOW TO CONNECT
PnP EXPANSION ADAPTER TO YOUR TAILLIGHTS
Tail light Connector
OEM Wiring Harness
Tail light Connector
OEM Wiring Harness
Step 4Step 4
Figure 4Figure 4
R
L
Next, grab the Redline Quick
Connect Expansion Adapter
Harness and Plug it into the
vehicle’s OEM wiring harness.
Plug the other end into the tail
light connector (See Figure 5).
Route the Redline Quick Connect
Expansion Adapter Harness from
the left tail light opening to the
right tail light opening, then
repeat the same steps for the
other side.
Use some zip ties to secure the flat 4PIN trailer
connector and reverse wire in place along the inner
bumper.
Finally, connect the available tailgate light bar to the
4PIN trailer connector and reverse wire for full
functionality testing
Installation
DISCLAIMER
Step 6
Step 7
Step 5Step 5
Figure 5Figure 5
OEM Wiring
Harness
OEM Wiring
Harness
Tail light
Connector
Tail light
Connector
OPT7 Lighting is not liable for damages or personal injuries while installing this
product. The Installation Guide is intended as assistance to reduce setup time.
OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7
Lighting will void product warranty.
/