iPE LP700-4 User manual

Type
User manual

iPE LP700-4 is a high-performance exhaust system designed to enhance the sound and power of your Lamborghini LP700. It features a valved muffler that allows you to control the exhaust note from a deep, throaty rumble to an aggressive roar. The system is made from high-quality stainless steel and is backed by a lifetime warranty.

Expected benefits of installing the iPE LP700-4 exhaust system include:

  • Improved exhaust note
  • Increased horsepower and torque
  • Reduced weight
  • Enhanced throttle response
  • Aggressive styling
  • Lifetime warranty

iPE LP700-4 is a high-performance exhaust system designed to enhance the sound and power of your Lamborghini LP700. It features a valved muffler that allows you to control the exhaust note from a deep, throaty rumble to an aggressive roar. The system is made from high-quality stainless steel and is backed by a lifetime warranty.

Expected benefits of installing the iPE LP700-4 exhaust system include:

  • Improved exhaust note
  • Increased horsepower and torque
  • Reduced weight
  • Enhanced throttle response
  • Aggressive styling
  • Lifetime warranty
WWW.IPE-f1.com
1
Installation instructions
iPE Exhaust system for
Lambo LP700
Preface
This document explains installation procedures that relates setting and
operation methods for the exhaust sold by IPE.
Important Notice
IPE developed this exhaust according to the improvement of stock .
Therefore, there will be no effect of the car from the original
manufacturer after installation. There is an inductive power supply
function between the car key and the car for many vehicle models.
Therefore, the car key should be kept away from the car with a distance
of at least five meters to maintain safe conditions.
The exhaust of a car right after driven is still in a high temperature. Thus,
please wear heat insulating gloves to replace the exhaust, or perform the
replacement after the temperature lowered to avoid burns.
For avoiding the generation of resonance, please don’t let the valve open
too early when setting the valve to open automatically. The opening of
the valve is recommended to be set to 60% of gas pedaling. Please refer
to page 21 for the explanation of detail setting.
IPE exhaust is designed according to the stock engine data. In case the
engine computer upgraded for increasing horse power, obvious
resonance in conjunction with this exhaust could occur. IPE also provide
revised exhausts for such vehicles, please contact us for further details.
WWW.IPE-f1.com
2
Tools required for
Operating Procedures
Star groove wrench, star
driver (E12, E14)
Outer hexagonal wrench
(13mm, 14mm, 16mm)
Torque wrench
Rust Preventive spray
WWW.IPE-f1.com
3
4
WWW.IPE-f1.com
iPE LP 700 Assembly of product appearance
(The product excluding headers)
Cat pipe
Muffler
Tips
Procedures and related points for
Demounting Stock Exhaust WWW.IPE-f1.com
5
1.Demounting engine room protection shield
2.Demounting hexagonal screw of engine protection shield
3.Demounting fixed piece of spoiler
4.Demounting fixed screws of both sides(interior)
5.Demounting fixed screws under spoiler
6.Loosening screws of spoiler hanger(2pcs both sides)
7.Unplugging the plugs under spolier(2 places)
WWW.IPE-f1.com
6
WWW.IPE-f1.com
7
8.Lifting up spoiler after loosened, and loosening the 4 screws onrear bumper
9.Demounting air intake net of both sides(reverse hook)
10.Demounting air intake base of both sides
8
WWW.IPE-f1.com
12.Loosening rear bumper screw after demounting both rear wheels and fenders
13.Demounting bottom fender and rear bumper screws
14.Demounting spoiler and bumper(2 men assist)
11.Loosening front bumper screws inside of both air intake
16.Demounting fixed screw of stock muffler
WWW.IPE-f1.com
9
15.Demounting rear bumping bar
17.Demounting bottom muffler hanging lug and clamp
WWW.IPE-f1.com
10
Demounting stock muffler when finished
WWW.IPE-f1.com
11
WWW.IPE-f1.com
18.Demounting cat pipe of both sides
-Demounting air intake pipe of left side
- Demounting lubricating oil pipe(leaking out about 1L)
- Demounting oxygen sensor and exhaust temperature sensor
of both sides, and clamps (2pcs of oxygen sensor and exhaust
temperature sensor both sides)
~Stock exhaust system domounting finished~
WWW.IPE-f1.com
12
Procedures and related points of iPE Exhaust
installation
1.Cat. Pipe installation and mounting clamps
Adjusting the length of one side of cat pipe before installed
2. Mounting oxygen sensor and exhaust temperature sensor of both sides
WWW.IPE-f1.com
13
3.Mounting muffler fixed screws
4.Mounting hanging lug base
5.Mounting tips
WWW.IPE-f1.com
14
6.Mounting tips of bumper
7.Mounting bumper and spoiler by reversing the order
WWW.IPE-f1.com
1515
8.Connecting vacuum source to muffler valve
9.After three-way branch connected, connecting with stock vacuum source
~ Above IPE exhaust system installation finished~
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

iPE LP700-4 User manual

Type
User manual

iPE LP700-4 is a high-performance exhaust system designed to enhance the sound and power of your Lamborghini LP700. It features a valved muffler that allows you to control the exhaust note from a deep, throaty rumble to an aggressive roar. The system is made from high-quality stainless steel and is backed by a lifetime warranty.

Expected benefits of installing the iPE LP700-4 exhaust system include:

  • Improved exhaust note
  • Increased horsepower and torque
  • Reduced weight
  • Enhanced throttle response
  • Aggressive styling
  • Lifetime warranty

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI