Eastwood Digital Tire Pressure Gauge/Inflator Operating instructions

Brand
Eastwood
Model
Digital Tire Pressure Gauge/Inflator
Type
Operating instructions

This manual is also suitable for

Eastwood 30535 is a Digital Tire Pressure Gauge/Inflator engineered to provide rugged reliability with a high degree of accuracy. Its capabilities include:

  • Precise pressure readout in increments of 0.1 psi for close tolerances required in racing applications.
  • Full rubber encapsulation for shock-proof protection and comfortable ergonomics.
  • Pressure Range: 0 to 100 psi [0 to 6.9 bar]
  • Available units of measure: psi, bar, kpa, and kg/cm2
  • Readout Resolution: 0.1 psi
  • Accuracy: +- 1%
  • Temperature Range: 32°– 104° F [0° – 40° C]
  • Battery Requirements: (2) CR2032 (included)

With these features, Eastwood 30535 is suitable for various applications such as:

Eastwood 30535 is a Digital Tire Pressure Gauge/Inflator engineered to provide rugged reliability with a high degree of accuracy. Its capabilities include:

  • Precise pressure readout in increments of 0.1 psi for close tolerances required in racing applications.
  • Full rubber encapsulation for shock-proof protection and comfortable ergonomics.
  • Pressure Range: 0 to 100 psi [0 to 6.9 bar]
  • Available units of measure: psi, bar, kpa, and kg/cm2
  • Readout Resolution: 0.1 psi
  • Accuracy: +- 1%
  • Temperature Range: 32°– 104° F [0° – 40° C]
  • Battery Requirements: (2) CR2032 (included)

With these features, Eastwood 30535 is suitable for various applications such as:

DIGITAL TIRE
PRESSURE GAUGE/INFLATOR
INSTRUCTIONS
Item #30535
CAUTION!
•
Keep the Inflator dry. Exposure to moisture can damage the precision
electronics inside.
•
Keep the Inflator away from electromagnetic interferences and fields.
•
Avoid dropping or bumping the Inflator.
2 Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com
The Eastwood Digital Tire Pressure
Gauge/Inflator is engineered and
built to provide rugged reliability with
a high degree of accuracy. Precise
pressure readout in increments of
0.1 psi deliver the close tolerances
required in racing applications.
The full rubber encapsulation
provides shock-proof protection
and comfortable ergonomics.
READ INSTRUCTIONS!
Thoroughly read and understand this instruction manual before use. Save manual
for future reference to safety warnings, maintenance and operating procedures.
Failure to follow all warnings can result in tool damage or serious physical injury.
SAFETY INFORMATION
CAUTION!
•
Do not exceed 100 psi [6.9 bar] or permanent damage to the unit
will occur.
•
Do not exceed the rated inflation pressure of a tire or violent explosion
could occur resulting in serious injury or death.
•
Do not use to inflate dry-rotted or damaged tires or violent explosion
could occur resulting in serious injury or death.
SPECIFICATIONS
•
Pressure Range = 0 to 100 psi [0 to 6.9 bar]
•
Available units of measure = psi, bar, kpa & kg/cm2
•
Readout Resolution = 0.1 psi
•
Accuracy = +- 1%
•
Temperature Range = 32°– 104° F [0° – 40° C]
•
Battery Requirements = (2) CR2032 (included)
•
Air Inlet = 1/4” FNPT
To order parts and supplies: 800.345.1178 >> eastwood.com 3
SET UP
•
Turn the Inflator “ON” by depressing and
releasing the “ON/UNIT” button (Fig A).
The Digital Display will read 0.0
•
Select the desired units of pressure
measurement by depressing and holding in the
“ON/UNIT” button for 3 seconds, until the units
change. (The “Units” indicator will appear to
the right of the 0.0). Repeat the procedure until
the desired units are achieved (psi, bar, kpa or
kg/cm2). Release the button.
•
Depress “LIGHT” button to illuminate display
backlight. Depress again to turn light off.
•
Depress the “OFF” button to turn Inflator off.
OPERATION
•
Connect air supply to the Inflator (Fig B).
•
Depress the Thumb Lever and attach the Fill
Fitting to the valve stem. Release Thumb Lever
to allow clamp to latch onto valve stem (Fig C).
•
Depress the Fill Lever fully to release air
into tire.
•
Release Fill Lever fully and read pressure in
Digital Display.
•
If pressure goes higher than desired, depress
the Fill Lever half-way to bleed off pressure
until proper pressure is achieved.
•
Depress the Thumb Lever once again to
release clamp and pull Fill Fitting from
valve stem.
BATTERY REPLACEMENT
•
Remove Battery Cover at left rear of gauge
housing by pushing in and release plastic latch.
•
Remove Batteries.
•
Replace Batteries with (2) CR2032.
NOTE: + side is placed facing upward and
under contacts (Fig D).
FIG. A
FIG. A
FIG. C
FIG. C
FIG. D
FIG. D
FIG. B
FIG. B
TROUBLESHOOTING
• B-Lo appears on display:
This indicates that the battery power is low. The Inflator will still function
but batteries should be replaced as soon as possible.
- Replace with (2) CR2032 batteries.
• Digital display is blank:
This indicates that the batteries are dead and require replacement.
- Replace with (2) CR2032 batteries.
© Copyright 2014 Easthill Group, Inc. Instruction part #30535Q Rev. 9/14
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: techelp@eastwood.com
PDF version of this manual is available online >> eastwood.com/30535manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
US and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: 610.323.6268 eastwood.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Eastwood Digital Tire Pressure Gauge/Inflator Operating instructions

Brand
Eastwood
Model
Digital Tire Pressure Gauge/Inflator
Type
Operating instructions
This manual is also suitable for

Eastwood 30535 is a Digital Tire Pressure Gauge/Inflator engineered to provide rugged reliability with a high degree of accuracy. Its capabilities include:

  • Precise pressure readout in increments of 0.1 psi for close tolerances required in racing applications.
  • Full rubber encapsulation for shock-proof protection and comfortable ergonomics.
  • Pressure Range: 0 to 100 psi [0 to 6.9 bar]
  • Available units of measure: psi, bar, kpa, and kg/cm2
  • Readout Resolution: 0.1 psi
  • Accuracy: +- 1%
  • Temperature Range: 32°– 104° F [0° – 40° C]
  • Battery Requirements: (2) CR2032 (included)

With these features, Eastwood 30535 is suitable for various applications such as:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents