Danfoss VLT AutomationDrive FC 360 Installation guide

Danfoss
Brand
Danfoss
Model
VLT AutomationDrive FC 360
Type
Installation guide

This manual is also suitable for

Danfoss VLT AutomationDrive FC 360 is a versatile frequency converter that provides precise control of AC motors. It is suitable for a wide range of applications, including pumps, fans, compressors, and conveyors. The FC 360 offers a number of advanced features, including:

  • Sensorless vector control: This feature provides high-performance control of induction motors, even at low speeds.
  • Built-in PLC: The FC 360 includes a built-in PLC that can be used to create custom control sequences.
  • Multiple communication options: The FC 360 supports a variety of communication protocols, including Modbus RTU, Profibus DP, and CANopen.

Danfoss VLT AutomationDrive FC 360 is a versatile frequency converter that provides precise control of AC motors. It is suitable for a wide range of applications, including pumps, fans, compressors, and conveyors. The FC 360 offers a number of advanced features, including:

  • Sensorless vector control: This feature provides high-performance control of induction motors, even at low speeds.
  • Built-in PLC: The FC 360 includes a built-in PLC that can be used to create custom control sequences.
  • Multiple communication options: The FC 360 supports a variety of communication protocols, including Modbus RTU, Profibus DP, and CANopen.
There are 2 types of control cassettes for VLT
®
Automa-
tionDrive FC 360: Standard Control Cassette and Control
Cassette with Profibus. The installation instructions in this
document apply to both. For Control Cassette with Profibus,
make sure to mount the Profibus decoupling kit after
mounting the control cassette. Instructions on mounting
decoupling kit can be found in the kit package.
Items Supplied
•
Either of the 2 types of control cassettes below:
•
Standard Control Cassette (132B0255)
•
Control Cassette with Profibus (132B0256)
•
Screws
Safety Instructions
WARNING
DISCHARGE TIME
The frequency converter contains DC-link capacitors, which
can remain charged even when the frequency converter is
not powered. Failure to wait the specified time after power
has been removed before performing service or repair work,
could result in death or serious injury.
•
Disconnect AC mains, permanent magnet type
motors, and remote DC-link power supplies,
including battery back-ups, UPS, and DC-link
connections to other frequency converters.
•
Wait for the capacitors to discharge fully, before
performing any service or repair work. The duration
of waiting time is specified in Table 1.1.
Voltage [V] Minimum waiting time [minutes]
415
380-480 0.37-7.5 kW 11-75 kW
High voltage may be present even when the warning LEDs are off!
Table 1.1 Discharge Time
Refer to VLT
®
AutomationDrive FC 360 Quick Guide for detailed
information about safe installation of the frequency converter.
Mounting
1. Connect the control cassette with the frequency
converter, bending the cable as shown in
Illustration 1.1.
Illustration 1.1 Bend the Connection Cable
Illustration 1.2 Connection Point on the Control Cassette
Installation Instructions
Control Cassettes
VLT
®
AutomationDrive FC 360
MI06C202 - Rev. 2013-09-18
2. Place the control cassette on the frequency converter
and slide it into place.
Illustration 1.3 Slide the Control Cassette into Place
3. Fasten the control cassette on the frequency
converter using 2 screws (supplied). Tightening
torque 0.7 - 1.0 Nm.
Illustration 1.4 Tighten Screws
*MI06C202*
MI06C202132R0208 Rev. 2013-09-18
  • Page 1 1
  • Page 2 2

Danfoss VLT AutomationDrive FC 360 Installation guide

Danfoss
Brand
Danfoss
Model
VLT AutomationDrive FC 360
Type
Installation guide
This manual is also suitable for

Danfoss VLT AutomationDrive FC 360 is a versatile frequency converter that provides precise control of AC motors. It is suitable for a wide range of applications, including pumps, fans, compressors, and conveyors. The FC 360 offers a number of advanced features, including:

  • Sensorless vector control: This feature provides high-performance control of induction motors, even at low speeds.
  • Built-in PLC: The FC 360 includes a built-in PLC that can be used to create custom control sequences.
  • Multiple communication options: The FC 360 supports a variety of communication protocols, including Modbus RTU, Profibus DP, and CANopen.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers