Multi-Tech Systems MT9234ZBA User manual

Brand: Multi-Tech Systems

Model: MT9234ZBA

Category: Modems

Type: User manual

MultiModem

ZBA

MT9234ZBA-Series

MT9234ZBA

MT9234ZBA-V

User Guide

2 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

MultiModem ZBA

MT9234ZBA-Series User Guide

MT9234ZBA, MT9234ZBA-V

PN S000387A, Version A

This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-

Multi-Tech Systems, Inc. makes no representations or warranty with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech

Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof

without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.

Check Multi-Tech’s web site for current versions of our product documentation.

Revisions

Revision Level Date Description

A 10/08/07 Initial release.

Trademarks

MultiModem, Multi-Tech, and the Multi-Tech logo are trademarks of Multi-Tech Systems, Inc.

Microsoft, Windows 2000, 2003, XP, and Vista are registered trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

Patents

This device covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560;

5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; 5,724,356; 5,673,268;

5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; 5,559,793;

5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; D353, 598;

5,355,365; 5,309,562; 5,301,274; 7082106;7082141;7092406. Other Patents Pending

World Headquarters

Multi-Tech Systems, Inc.

2205 Woodale Drive

Mounds View, Minnesota 55112

Phone: 763-785-3500 or 800-328-9717

Fax: 763-785-9874

Technical Support

Country By Email By Phone

Europe, Middle East, Africa: [email protected] +(44) 118 959 7774

U.S., Canada, all others: support@multitech.com (800) 972-2439 or (763) 717-5863

Internet Address:

http://www.multitech.com

Table of Contents

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 3

Table of Contents

CHAPTER 1 – INTRODUCTION................................................................................................................................ 5

Features.........................................................................................................................................................5

AT Commands Info........................................................................................................................................5

Technical Specifications................................................................................................................................6

CHAPTER 2 – INSTALLATION.................................................................................................................................8

Safety Warnings............................................................................................................................................8

Step 1: Change the Internal Jumpers............................................................................................................8

Step 2: Connect the Modem to Your PC.....................................................................................................10

Step 3: Install the Modem Driver.................................................................................................................11

Step 4: Configure the Modem for Your Country or Region – Global Product Only.....................................11

CHAPTER 3 – OPERATION.......................................................................................................................................13

About the Front Panel..................................................................................................................................13

Leased-Line Operation................................................................................................................................13

Connecting to the Internet...........................................................................................................................14

CHAPTER 4–REMOTE CONFIGURATION.........................................................................................................15

Basic Procedure..........................................................................................................................................15

Setup ...........................................................................................................................................................15

CHAPTER 5 – CALLBACK SECURITY.................................................................................................................16

Changing the Setup Password....................................................................................................................16

Turning Callback Security On and Off.........................................................................................................16

Setting Callback Security Message Parity...................................................................................................17

Assigning Callback Passwords and Phone Numbers.................................................................................17

Calling Procedures......................................................................................................................................17

Callback Assignments Form........................................................................................................................20

CHAPTER 6 – TROUBLESHOOTING ...................................................................................................................21

None of the Indicators Light.........................................................................................................................21

The Modem Does Not Respond to Commands ..........................................................................................21

The Modem Cannot Connect When Dialing................................................................................................22

The Modem Disconnects While Online.......................................................................................................23

Modem Cannot Connect When Answering.................................................................................................23

File Transfer Is Slower Than It Should Be...................................................................................................23

Data Is Being Lost.......................................................................................................................................24

There Are Garbage Characters on the Monitor...........................................................................................24

The Modem Doesn’t Work with Caller ID....................................................................................................24

Fax and Data Software Can’t Run at the Same Time.................................................................................24

CHAPTER 7 – WARRANTY, SERVICE, AND TECHNICAL SUPPORT ...................................................25

APPENDIX A – UPGRADING THE MODEM’S FIRMWARE .......................................................................27

Upgrade Overview.......................................................................................................................................27

APPENDIX B – REGULATORY COMPLIANCE................................................................................................29

FCC Part 15 Regulation ..............................................................................................................................29

FCC Part 68 Telecom..................................................................................................................................29

Table of Contents

4 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Fax Branding Statement..............................................................................................................................30

Canadian Limitations Notice........................................................................................................................30

Industry Canada..........................................................................................................................................30

EMC, Safety and R&TTE Directive Compliance.........................................................................................30

International Modem Restrictions................................................................................................................31

New Zealand Telecom Warning Notice.......................................................................................................31

South African Statement..............................................................................................................................31

APPENDIX C – WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT............................................32

APPENDIX D – INSTALLING A MODEM UNDER LINUX...........................................................................33

APPENDIX E – CONNECTING TO A CISCO ROUTER..................................................................................34

APPENDIX F – C-ROHS HT/TS SUBSTANCE CONCENTRATION..........................................................36

INDEX................................................................................................................................................................................37

Chapter 1 – Introduction

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 5

Chapter 1 – Introduction

Congratulations on your purchase of the MultiModem ZBA modem. You have acquired one of the finest intelligent

voice/data/fax modems available today from one of the world’s oldest modem manufacturers: Multi-Tech Systems, Inc.

The MT9234ZBA-Series is available in global and non-global builds with and without the voice feature. The MT9234ZBA

global product is approved in 40+ countries. The MT9234ZBA with the voice feature supports voice mail and a full-duplex

speakerphone. This allows you and the caller to speak and listen at the same time.

This user guide will help you to install, configure, test and use your modem.

Check Multi-Tech’s web site for current versions of our product documentation.

Features

Increased Upload Speeds. With the V.92 MultiModem ZBA business modem, you can achieve an upload speed of 48K

bps (30% increase over V.90 modems). This higher upstream speed reduces data transfer time for large e-mails with

attachments and for ftp site uploads, as well as improves operation for interactive applications.

V.44 Compression. V.44 compression enables data throughput rates of higher than 300K bps - much faster than

V.42bis data compression rates of 150 - 200K bps. For users, it means that your Web browsing will be much faster.

Enhanced Fax Features. The MultiModem ZBA business modem supports V.34 fax and Error Correction Mode

providing significant performance and reliability enhancements over previous fax standards. V.34 sends and receives

faxes at 33.6K, more than double the speed of the V.17/14.4K fax standard. Error Correction Mode adds reliablility while

increasing performance of fax transmissions. Together these enhancements increase the performance of the modem to

levels previously only found in more expensive dedicated fax boards and machines.

Remote Configuration. Whether you provide connectivity for a sales office just miles away or for multiple office across

the world, the MultiModem ZBA lets you take care of the configuration from a central site.

Callback Security. The MultiModem ZBA provides password protection and helps reduce long distance charges for

remote offices and users requiring access to the central site LAN. This modem supports 30 passwords and three

configuration options. With the "fixed" callback option, the central site modem stores a password and the remote user's

phone number. Once the remote site enters their password, the central site's modem calls back using the number stored

in its database. The "variable" option lets users, such as road warriors, enter their fixed password and a call back number

each time they call. The "pass through" option is used to provide the security of password protection, while bypassing the

call back process.

Global Approvals. With the globally approved MultiModem ZBA business modem, you need just one modem for

worldwide use. This model has approvals in many countries so you can ship one SKU (stock unit) virtually anywhere in

the world. Localization kits are available for country-specific power cords, phone cords and telco adapters. Go to

www.multitech.com/globalmodem for details.

AT Commands Info

The AT Commands, S-Registers, and Result Codes for the MT9234ZBA-Series Modems are published in a separate

Reference Guide. This guide is included on the MT9234ZBA-Series product CD. You can open the guide from the CD or

you download the guide to your hard drive and then open it.

Chapter 1 – Introduction

6 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Technical Specifications

The MT9234ZBA-Series modem meets the following specifications:

Trade Name MultiModem

ZBA

Model Number MT9234ZBA

Build Number MT9234ZBA, MT9234ZBA-V

Server-to-Client 56K speeds when accessing a V.90 or V.92 server (actual

Data Rates speed depends on server capabilities and line conditions)

Client-to-Server Up to 48Kbps when accessing a V.92 server (actual speed

Data Rates depends on server capabilities and line conditions); otherwise the same as

client-to-client data rates (see next listing).

Client-to-Client 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800 bps,

Data Rates 14400, 12000, 9600, 7200, 4800, 2400, 1200, 0-300 bps

Fax Data Rates 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800

Voice Compatibility TIA/EIA IS-101 (Voice Option only)

Data Format Serial, binary, asynchronous

Modem Compatibility ITU-T V.92, V.90, V.34 enhanced, V.34, V.32bis, V.32, V.22bis, V.22; Bell 212A

and 103/113; ITU-T V.21 & V.23; V.42, V.42bis, V.44.

Fax Compatibility ITU-T “Super” Group 3; Class 1.0, 2.0, 2.1; T.4; T.30; V.21; V.27ter; V.29; V.34;

V.17; and TIA/EIA Class 1, 2; TR29.2

Video Compatibility ITU-T V.80 for H.324 video conferencing

Error Correction ITU-T V.42

Data Compression ITU-T V.44 (6:1 throughput)

Speed Conversion Serial port data rates adjustable to 300, 1200, 2400, 4800, 9600, 19,200,

38,400, 57,600, 115,200, and 230,400 bps

Mode of Operation Fax online modes; full duplex over dial-up lines

Flow Control XON/XOFF (software), RTS/CTS (hardware)

Intelligent Features Plug and play; fully AT command compatible; dialing options, autoanswer;

adaptive answer; EIA extended automode; adaptive line probing; automatic

symbol and carrier frequency during start-up, retrain, and rate renegotiation;

DTMF detection; call status display, auto-parity and data rate selections;

keyboard-controlled modem options; non-volatile memory; remote configuration;

DTR dialing; callback security; A-law support in 56K modes; 11-bit support; real-

time fax compression conversion; U.S. Caller ID reporting; quick-connect startup

(V.92).

Command Buffer 40 characters

Transmit Level -12 dBm (Eruo/NAM) – varies by country/region setting

Frequency Stability ±0.01%

Receiver Sensitivity -43 dBm under worst-case conditions

AGC Dynamic Range 43 dB

Interface TIA/EIA RS-232C/ITU-T V.24/V.28

Connectors DB25F RS-232C connector; 2 RJ-11 telephone jacks; power jack

Cables Country-specific telephone; power cables; serial cable

Chapter 1 – Introduction

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 7

Note: Any cables connected to the computer should be shielded to reduce

interference.

Diagnostics Power-on self test, local analog loop, local digital loop, remote digital loop.

Indicators LEDs for Transmit Data, Receive Data, Carrier Detect, 56K bps, 33.6K bps,

14.4K bps, Off Hook, Terminal Ready, Error Correction, Fax.

Speaker Internal speaker for call progress monitoring.

Manual Control Power switch

Operating Temperature -40°– 60°C (-40°–140°F) ambient under closed conditions; humidity range 20–

90% (non-condensing)

Power Requirements Global modems: 100–240 VAC, 50/60 Hz universal power supply

Non-global modems: 115 VAC, 60 Hz or 230 VAC, 50 Hz power supply

Power Consumption 9 VDC, 300 mA maximum

Dimensions 10.8 cm wide x 14.8 cm long x 2.9 cm high (4.25" x 5.8" x 1.15")

Weight 224 g (8 oz)

Limited Warranty 10 years

Chapter 3 – Operation

8 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Chapter 2 – Installation

This chapter shows you step-by-step how to set up your Multi-Tech MT9234ZBA modem.

Safety Warnings

• Use this product only with UL- and CUL-listed computers (U.S.A. and Canada)

• To reduce the risk of fire, use only 26 AWG (.41mm) or larger telephone wiring.

• Never install telephone wiring during a lightning storm.

• Never install a telephone jack in a wet location unless the jack is specifically designed for wet locations.

• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the

network interface.

• Use caution when installing or modifying telephone lines.

• Avoid using a telephone during an electrical storm; there is a risk of electrical shock from lightning.

• Do not use a telephone in the vicinity of a gas leak.

• This product must be disconnected from the telephone network interface when servicing.

Step 1: Change the Internal Jumpers

This step is required only if:

• You intend to use the modem on a leased line.

• You intend to add a monophonic external speaker to your modem with the voice option. No changes are needed

for stereo.

This will require you to open the modem and move one or more jumpers on the modem’s printed circuit board.

Warning: The following procedure must be performed by authorized service personnel.

Caution: The circuit board can be harmed by static electricity. Before you open the case, touch a grounded object, such

as the metal chassis of your computer, to discharge any static electricity in your body, then touch the metal shell of the

modem’s RS-232 connector to ensure that there is no voltage difference between you and the modem.

Opening the Modem

1. If the modem is connected, turn it off and remove all connecting cables (including the power and line

cables).

2. Turn the modem upside down.

3. On the bottom of the modem are two screws, which hold the case together. Remove both screws and set

them aside.

4. Turn the modem right side up.

5. Remove the top part of the modem case.

6. To close the modem, reverse Steps 1–5.

Chapter 3 – Operation

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 9

Location of the Jumpers

Note: The Speaker Mode Jumper is for the Modem with the Voice Option

Changing the Dial-Up/Leased-Line Jumper

As shipped from the factory, your modem is configured for normal dial-up operation. That is, the modem must

dial a phone number to connect to another modem. To use the modem on a leased line, you must change

jumper J2 to select leased line operation, and J3 to select whether it will be the originating or the answering

modem. If dial-up operation is selected, J3 has no effect.

See Chapter 3 for additional leased line information.

• The factory default is the answer position. This makes the modem the answering modem on the leased

line.

• To use the modem on a leased line, move the J2 jumper plug from the default dial-up position to the

leased line position.

• To make the modem the originating modem on the leased line, move the J3 jumper plug to the originate

position.

Changing the Voice Jumper

The speaker jumper is next to the external speaker jack.

• The factory default position of the voice jumper is set for a stereo speaker or sound card. A jumper plug

covers both pins of the jumper.

• To use the modem with a monophonic external speaker, remove the jumper plug from the jumper pins.

You can store it by placing it on one jumper pin.

Chapter 3 – Operation

10 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Step 2: Connect the Modem to Your PC

Turn off your computer. Place the modem in a convenient location, and then connect it to your computer’s serial port, the

telephone line or leased line, AC power, and, optionally, your telephone.

Connections - No Voice

Connections With Voice

Connect the Modem to Your PC

Plug one end of the serial cable into the RS232 connector on the modem and the other end into a serial port

connector on your computer, such as COM1 or COM2.

Connect the Modem to the Telephone Line

Plug one end of the modular telephone cable into the modem’s LINE jack and the other end into a standard

phone wall jack.

Important: The LINE jack is not interchangeable with the PHONE jack. Do not plug the telephone into the

LINE jack or the line cable into the PHONE jack.

Note: Regulatory agencies may impose certain restrictions on equipment connected to public telephone

systems. For more information, see Appendix B.

Connect the Two-Wire Leased Line (Leased Line Only)

Plug one end of a two-wire telephone cable into the modem’s LINE jack and the other end to a two-wire

leased line wall jack or terminals.

Note: Before you can use the modem on a leased line, you must first change the internal jumpers. See “Step

2: Change the Internal Jumpers.”

Connect the Modem to a Phone (Optional)

If you want to connect a phone to same line as the modem, plug it into the modem’s PHONE jack.

Important: The PHONE jack is not interchangeable with the LINE jack. Do not plug the telephone into the

LINE jack or the line cable into the PHONE jack.

Connect a Microphone (Voice Option)

For voice mail or speakerphone applications, plug an unamplified microphone into the MIC jack on the side of

the modem. The microphone should have a stereo 1/8-inch mini plug. Do not use a monophonic microphone.

Chapter 3 – Operation

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 11

Connect Speakers (Voice Option)

For speakerphone or voice mail applications, use a 1/8-inch plug male-to-male stereo patch cord to connect

the SPKR jack on the side of the modem to the LINE IN jack on your sound card. If your sound card does not

have a LINE IN jack, use its MIC jack. The stereo male-to-male patch cord can be purchased at a local PC

retail store.

If you do not have a sound card, you can plug an unamplified speaker directly into the SPKR jack.

Connect the Modem to the AC Power Outlet

The power switch is located on the right side of the modem. Make sure it is set to OFF.

Attach the appropriate interchangeable blade module to the power supply module. Connect the power lead

from the power supply module into the PWR jack on the modem. Now, plug the power supply module into

your power source.

Note: Use only the power supply supplied with the modem. Use of any other power supply voids the warranty

and can damage the modem.

Power-On Test

Test the modem by turning it on. When you turn it on, the modem performs a diagnostic self-test, after which

the 56 indicator should light. If this does not happen, check that the power switch is on, the power supply is

solidly connected, and the AC outlet is live. If these measures do not work, refer to Chapter 6,

“Troubleshooting”.

Step 3: Install the Modem Driver

If you use Windows 2000 or above, you must install the modem driver. The modem driver tells Windows how to control

the modem. If you use a Linux operating system, please refer Appendix D. If you use another operating system, please

refer to its documentation for modem installation information.

Installing the Modem Driver

Make sure your modem is connected properly, and then turn on your computer. Windows should detect your new

modem and open the Install New Modem wizard.

Note: If Windows cannot find a modem, your modem may be turned off, it may be plugged into the wrong

connector on your computer, or the serial cable may be faulty. See “None of the LEDs Light When the Modem Is

Turned On” and “The Modem Does Not Respond to Commands” in Chapter 6, “Troubleshooting.”

Insert the product CD into your CD-ROM drive, and then click OK.

Windows installs the modem driver.

Click Finish to exit.

Step 4: Configure the Modem for Your

Country or Region – Global Product Only

Different countries have different requirements for how modems must function. Therefore, before you use your modem,

you must configure it to match the defaults of the country/region in which you are using it. You must also do this if you

move the modem to another country/region after it has been configured for the first country/region. You can use one of

two configuration methods:

1. Use the Global Wizard to Configure Your Modem

2. Use AT Commands to Configure Your Modem

Using the Global Wizard to Configure Your Modem

The Global Wizard configuration utility is recommended for computers running Windows 2000 or newer.

1. Insert the MultiModem ZBA product CD into the CD-ROM drive. The Autorun menu should appear.

2. Click Initial Setup and Country/Region Selection.

3. Choose either:

Run Global Wizard from CD. This will not load the wizard onto your hard drive, or

Install Global Wizard on the HD. This will install the wizard onto your hard drive for future use.

Chapter 3 – Operation

12 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

4. The Global Wizard dialog box appeared. Click Next.

5. The Global Wizard searches for your modem and identifies it. Click Next.

6. Select the country/region in which the modem will be used. Click Next.

7. Review your country/region choice. If it is correct, click Next to configure the modem.

8. When Global Wizard announces that the parameters have been set, click Finish to exit.

Using AT Commands to Configure Your Modem

Non-Windows users can configure the modem using AT commands. You must enter these commands in your

communication program’s terminal window.

1. Run your favorite communication program and open the program’s terminal window.

2. To configure the modem for a specific country/region:

Type AT%T19,0,nn, where nn is the country/region code in hexadecimal notation.

Click E

NTER. The message OK displays.

3. To verify that the correct country/region has been configured, type:

ATI9 and click E

NTER.

The country/region code displays:

Example: Country/Region AT Command (hexadecimal)

Result code (decimal)

Euro/NAM AT%T19,0,34 (default) 52

A list of country/region codes can be found on the Multi-Tech Web site at:

http://www.multitech.com/PRODUCTS/Info/appro

vals

Then click on global modems. The Global Modem Country Approvals page displays.

On this page you can view approvals, configuration strings and responses by

country and products.

Chapter 3 – Operation

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 13

Chapter 3 – Operation

About the Front Panel

The LED indicators on the front panel indicate status, configuration, and activity:

TD – Transmit Data. Flashes when the modem is transmitting data to another modem.

RD – Receive Data. Flashes when the modem is receiving data.

CD – Carrier Detect. Lights when the modem detects a valid carrier signal from another modem. It is on when the

modem is communicating with the other modem, and off when the link is broken.

56 – 56K Mode (56,000–28,000 bps). Lights whenever the modem is set for or connects using the V.90 or V.92 protocol.

The actual connection speed depends on ISP server capabilities and line conditions.

33 – V.34 Mode (33,600–2,400 bps). Lights whenever the modem connects using the V.34 protocol.

14 – V.32bis Mode (14,400–7,200 bps). Lights when the modem connects using the V.32bis protocol. The modem can

connect at lower than V.32bis speeds, but no speed indicator lights during the connection.

OH – Off-Hook. Lights when the modem is off-hook, which occurs when the modem is dialing, online, or answering a

call. Flashes when the modem pulse-dials.

TR – Terminal Ready. Lights when a communications program is using the modem. It means the modem is ready for an

outgoing or incoming call. It goes off when the communications program disconnects the serial port. When it goes

off, a connected modem will also disconnect.

EC – Error Correction (V.42). Lights continuously when the modem is in V.42 error correction mode, and flashes when

compression is activated.

FX – Fax. Lights when the modem is in fax mode.

Note: When you turn on the modem, the protocol indicators flash briefly as the modem does a self-test, after which the

56 indicator lights. After a call, the indicator for the protocol used in the connection remains lit until another call is

made or the modem is reset. If you connect at a rate under 14,400 bps, all protocol indicators remain off after the

connection is broken, even though the modem is still turned on.

Leased-Line Operation

The MultiModemZBA modem can be used on a two-wire leased line.

A leased line is a private, permanent telephone connection between two points. Unlike normal dialup connections, a

leased line is always active. The modems automatically connect when they are attached to the line and are turned on.

Because a leased line is always active, one of the two modems on the line must be configured as the originate modem

and the other as the answer modem; however, it does not matter which is which.

In the event of an interruption, leased-line modems automatically reconnect when the data line or power is restored.

Setup

1. Open the modem and change jumper J2 to select leased-line operation, and jumper J3 to select either

originate or answer operation, depending upon how you intend to use the modem. See Chapter 2 for the

detailed procedure.

2. Connect a modular telephone cable to the LINE jack. Connect the other end of the cable to a two-wire

lease-line jack or terminals supplied by the telephone company.

3. Turn on the modem.

Chapter 3 – Operation

14 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Connecting to the Internet

Your Multi-Tech modem is your gateway to the Internet and the World Wide Web. To access the Internet and Web via

your modem, you must establish a dial-up account with an Internet service provider (ISP). To locate an ISP near you,

look in a local directory or computer publication. Your ISP should provide you with the following information:

• User name (also called user ID)

• Password

• Access number (the number you call to connect to the server)

• Host name and/or domain name

• Domain Name Server (DNS) server address

If, besides the Web, you use the Internet for e-mail and newsgroups, your ISP should also provide you with the following

information:

• E-mail or POP mail address

• POP server address

• Mail or SMTP address

News or NNT server address

Chapter 4 – Remote Configuration

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 15

Chapter 4–Remote Configuration

Remote configuration is a network management tool that allows you to configure MT9234ZBA modems anywhere in your

network from one location. With password-protected remote configuration, you can issue AT commands to a remote

modem for maintenance or troubleshooting as if you were on site.

Basic Procedure

The following steps can be used when the connection is established by the local or the remote modem.

Note: The remote computer must be running and a communication program must be ready for a data connection, which

will be indicated by a lighted TR indicator on the front of the modem.

1. Establish a data connection with a remote MT9234ZBA modem.

2. Send three remote configuration escape characters followed by AT and the setup password, and press

NTER. Example: %%%ATMTSMODEM. You have four tries to enter the correct password before being

disconnected. If the password is correct, the remote modem responds with OK.

3. You can now send AT commands to configure the remote modem.

4. When you have finished configuring the remote modem, save the new configuration by typing AT&W0 and

pressing E

NTER.

5. Type ATO and press E

NTER to exit remote configuration. You can now break the connection in the normal

way.

Setup

Multi-Tech modems are shipped with a default setup password (MTSMODEM). Because anyone who has the User

Guide knows the default setup password, you should change the password and possibly also the remote configuration

escape character.

Changing the Setup Password

1. Open a data communications program such as HyperTerminal.

2. In the terminal window, type AT#SMTSMODEM (or AT#Sxxxxxxxx if you have replaced the

MTSMODEM password with xxxxxxxx) and press E

NTER. The modem responds with OK if the setup

password is correct, and ERROR if it is wrong.

3. To change the password, type AT#S=xxxxxxxx, where xxxxxxxx stands for the password, and then

press ENTER. The password can include any keyboard character, and can be up to eight characters long.

The modem responds with OK.

CAUTION: Passwords are case-sensitive. The next time you enter the password, it must be in the same

case as you set it up.

4. The new password is saved automatically. You can now either enter more AT commands or exit the data

communications program. The next time you wish to set up the modem, you must use the new password.

Changing the Remote Escape Character

To further improve security, you can change a remote modem’s remote configuration escape character either

locally or remotely. The remote configuration escape character is stored in register S9. The factory default is 37,

which is the ASCII code for the percent character (%). Setting S9 to 0 (zero) disables remote configuration

entirely.

CAUTION: If you do this remotely, you won’t be able to change it back remotely.

1. Establish a remote configuration link with the remote modem as described in Basic Procedure.

2. Type ATS9=n, where n is the ASCII code for the new remote configuration escape character, and then

press E

NTER.

3. Save the new value by typing AT&W and pressing E

NTER.

4. Type ATO and press ENTER to exit remote configuration.

Chapter 5 – Callback Security

16 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Chapter 5 – Callback Security

This chapter describes how to use callback security with your modem. Callback security protects your network from

unauthorized access and helps control long-distance costs. When callback security is enabled, all callers are requested

to enter a password. If a valid password is received, the modem hangs up and returns the call by dialing a phone number

that is stored with the password. The person being called back must then enter the password a second time to establish

a connection.

Up to 30 callback passwords and dialing strings can be stored in the modem. Each dialing string can be up to 34 or 35

characters long and can contain commands as well as phone numbers. For mobile callers, the dialing string can be

programmed to allow the caller to bypass the stored callback number by entering a temporary callback number, to enter

an extension at the callback number, or to make a direct connection without callback.

For local security, the passwords and dialing strings that are stored in the modem are protected from tampering by a

setup password, which you should change when you set up the modem. You can further protect the modem against

tampering by disabling its ability to respond to most AT commands. To check for attempted break-ins, you can request

the modem to display the number of failed password attempts.

Your modem was shipped with a default setup password (MTSMODEM). The same password is used for both callback

security and remote configuration (Chapter 4). Because anyone who has access to this guide has access to the default

password, you should change the password during your initial setup.

Changing the Setup Password

1. Open a data communications program such as HyperTerminal.

2. In the terminal window, type AT#SMTSMODEM (or AT#Sxxxxxxxx if you have replaced the MTSMODEM

password with xxxxxxxx). Press E

NTER. The modem responds with OK if the setup password is correct and

ERROR if it is wrong.

3. To change the password, type AT#S=xxxxxxxx, where xxxxxxxx stands for the password, and then press

NTER. The password can include any keyboard character, and can be up to eight characters long. The modem

responds with OK.

4. The new password is saved automatically. You can now either enter more AT commands or exit the data

communications program. The next time you wish to set up the modem, you must use the new password.

CAUTION: Passwords are case-sensitive. The next time you enter the password, it must be in the same case as

you set it up.

Turning Callback Security On and Off

Callback security must be turned on to enter many callback security commands.

1. Open a data communications program such as HyperTerminal.

2. In the terminal window, type AT#Sxxxxxxxx, where xxxxxxxx is your password. Press E

NTER. The modem

responds with OK if the setup password is correct and ERROR if it is wrong.

3. Type one of the following commands:

• To turn off callback security: Type AT#CBS0 and press ENTER. Callers no longer need a password to

connect to the modem, the modem is unable to call them back, and the stored dialing command locations

0–3 become available.

• To turn on both local and remote callback security: Type AT#CBS1. Press ENTER. With local security

turned on, you must enter the setup password before you can enter any AT command except the AT, ATIn,

and AT#Sxxxxxxxx commands. For a description of remote callback security, see the following paragraph.

• To turn on remote callback security only: Type AT#CBS2 and press ENTER. With remote callback

security turned on, each caller is asked to enter a password, is called back, and then is asked to enter the

password again before a connection can be made. Also, dialing command locations 0–3 for use with the

DS=y dialing command are replaced by callback dialing command locations 0–29.

• To temporarily disable callback security if the modem is set to #CBS1 or #CBS2 (for instance, to call

another modem): Type AT#CBS3 and press ENTER. The modem returns to its original setting when you

issue the hangup command (+++ATH) or the modem is reset. Note that if a remote modem breaks the

connection, callback security remains disabled.

Chapter 5 – Callback Security

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 17

Setting Callback Security Message Parity

The modem’s password prompt and messages parity must match the parity of the computer to which the modem is

connected.

1. Open a data communications program such as HyperTerminal.

2. In the terminal window, type AT#Sxxxxxxxx, where xxxxxxxx is your password. Press E

NTER. The modem

responds with OK if the setup password is correct and ERROR if it is wrong.

3. The modem’s parity default value is No parity (AT#CBP0). To change the modem’s default to use even parity,

type AT#CBP2. Press E

NTER. For odd parity, type AT#CBP1. Press ENTER.

4. To store the new parity value, type AT&W. Press E

NTER.

Assigning Callback Passwords and Phone

Numbers

1. Open a data communications program such as HyperTerminal.

2. In the terminal window, type AT#Sxxxxxxxx, where xxxxxxxx is your password. Press E

NTER. The modem

responds with OK if the setup password is correct and ERROR if it is wrong.

3. Enable callback security by typing AT#CBS1 or AT#CBS2 and pressing E

NTER.

4. To store a callback password for the first callback memory location, type AT#CBN0=xxxxxxxx, where xxxxxxxx

is the first password. Press E

NTER. The password must be unique, must be six to eight characters in length, and

must not contain a + or - character.

5. To store a callback password for the second callback memory location, type AT#CBN1=xxxxxxxx, where

xxxxxxxx is the second password. Press E

NTER. Note that the memory location number in the command is

incremented by one.

6. Repeat as many times as necessary, up to memory location 29, until all passwords are entered.

7. To store a callback phone number in the first memory location, type AT&Z0=[+][-]ATxxxxxxxx[,???], where

xxxxxxxx is the dialing string. Press E

NTER. The phone number must be preceded by DT for tone dialing or DP

for pulse dialing. The dialing string can also include other AT commands.

Example: AT&Z0=+-ATM0DT5551212. Up to 35 characters can be used. The +, -, and ??? characters are

optional:

+ Number entry. Enables a mobile caller to enter his current phone number for callback.

- Direct connection. Enables a caller to choose direct connection without being called back.

,??? Extension entry. Must be used with the + command. Enables a caller to enter an extension number for

callback. The number of ? characters must equal the number of digits in the extension.

8. To store a callback phone number in the second memory location, type AT&Z1=[+][-]ATxxxxxxxx[,???], where

xxxxxxxx is the dialing string, and press E

NTER. Note that the memory location number in the command is

incremented by one.

9. Repeat, through memory location 29, until all dialing strings are entered.

10. To review your entries, type AT&V and press E

NTER.

Note: A form is provided on the last page of this chapter to help you plan or keep track of password and phone

number assignments.

Calling Procedures

Use the following procedures to call a modem that has callback security enabled. Note that Autoanswer must be enabled

on the calling modem (S0=1).

Password-Only Callback

Use this procedure when calling from a fixed location.

1. Using a data communications program such as HyperTerminal, dial the number of the callback modem.

2. When the connection is established, the callback modem responds with the following message:

Password>

3. Type the password corresponding to the phone number for your modem. Press E

NTER. You have three

attempts or one minute to enter a valid password.

4. If the password is valid, the following message appears, and the modems disconnect:

OK Disconnecting

Chapter 5 – Callback Security

18 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

5. After the delay specified by the #CBDn command, the callback modem calls the number associated with

the password. If the callback modem is unable to establish a connection, it tries again, up to the number

of attempts specified by the #CBAn command.

6. After the modems reconnect, the following message reappears:

Password>

7. Type the same password that you used to initiate the call. You are allowed three attempts to enter the

password, after which you will be disconnected.

8. If the password is valid, the following message appears and the modems establish a working connection:

OK Connecting

Number-Entry Callback

Mobile callers should use this procedure when calling from a phone number different from that stored with the

password. The password that is used must be set up for optional number-entry callback.

1. Using a data communications program such as HyperTerminal, dial the number of the callback modem.

2. When the connection is established, the callback modem responds with the following message:

Password>

3. Type a number-entry password, press the plus key (+), type ATDT and the number to call back to, and

press E

NTER. You have three attempts or one minute to enter a valid password.

Note: When you type your phone number, be sure to include the long distance and area codes if they are

needed.

4. If the password is valid, the following message appears, and the modems disconnect:

OK Disconnecting

5. After the delay specified by the #CBDn command, the callback modem calls the number that you entered

after the + character. If the callback modem is unable to establish a connection, it tries again, up to the

number of attempts specified by the #CBAn command.

6. After the modems reconnect, the following message reappears:

Password>

7. Type the same password that you used to initiate the call. You are allowed three attempts to enter the

password, after which you will be disconnected.

8. If the password is valid, the following message appears and the modems establish a working connection:

OK Connecting

Extension-Entry Callback

Use this procedure when calling from an extension at the callback number. The password that you use must be

set up for an optional extension-entry callback.

1. Using a data communications program such as HyperTerminal, dial the number of the callback modem.

2. When the connection is established, the callback modem responds with the following message:

Password>

3. Type an extension-entry password, press the plus key (+), type the extension to call back to, and press

NTER. You have three attempts or one minute to enter a valid password.

4. If the password is valid, the following message appears, and the modems disconnect:

OK Disconnecting

5. After the delay specified by the #CBDn command, the callback modem calls the extension that you

entered after the + character. If the callback modem is unable to establish a connection, it tries again, up

to the number of attempts specified by the #CBAn command.

6. After the modems reconnect, the following message reappears:

Password>

7. Type the same password you used to initiate the call. You are allowed three attempts to enter the

password. After that, you will be disconnected.

8. If the password is valid, the following message appears, and the modems establish a working

connection:

OK Connecting

Chapter 5 – Callback Security

Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A) 19

Direct Connection

Use this procedure when you want to connect without first being called back. The password that you use must be

set up for an optional direct connection.

1. Using a data communications program such as HyperTerminal, dial the number of the callback modem.

2. When the connection is established, the callback modem responds with the following message:

Password>

3. Type a direct connection password, press the - key, and then press ENTER. You have three attempts or

one minute to enter a valid password.

4. If the password is valid, the following message appears and the modems establish a working connection:

OK Connecting

Note: You can make all calls direct connect regardless of whether the password or phone number has the -

character by using the %H1 command

Callback Security Commands

The AT Commands related to Callback Security are included in the AT Commands Reference guide included on

MT9234ZBA-Series product CD.

Chapter 5 – Callback Security

20 Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387A)

Callback Assignments Form

Location Password Telephone Number

Page is loading ...

Multi-Tech Systems MT9234ZBA User manual

Brand: Multi-Tech Systems

Model: MT9234ZBA

Category: Modems

Type: User manual

Download PDF

report

Multi-Tech Systems MT9234ZBA User manual

Multi-Tech Systems MT9234ZBA User manual

Related papers

Other documents