Posiflex LM-6801 User manual

Posiflex
Brand
Posiflex
Model
LM-6801
Category
LED displays
Type
User manual
Page 1
FEATURES
• Light weight and high luminance LCD monitor
for industrial and commercial use
• Application covers POS, POIS (Kiosk), Factory Automation etc.
• High quality 12.1” TFT LCD panel with scaling up function for full screen
display
• Display resolution up to 1024 x 768 pixels
• Tilt and swivel adjustable construction
• Second display for Posiflex terminal with Gen 6 base stand.
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.
ABOUT THIS MANUAL
This manual assists the user to utilize the LCD Monitor LM-6801. This product provides exquisite capability over a stable and
adjustable LCD monitor with minimal footprint.
The manufacturer of the LM-6801 LCD monitor heartily apologizes to the user for reserving the right to change or to modify this
manual without notice due to the rapid and constant progress and improvement on science and technology. The user may always
obtain the most up to date information through any of our web sites: http://www.posiflex.com, http://www.posiflex.com.tw,
http://www.posiflexusa.com.
Copyright Posiflex Technology, Inc. 2010
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
P/N:
19050906010
LM-6801
LCD Monitor
User’s Manual
Rev. Original
Page 2
I. PARTS IDENTIFICATION
A. PRODUCT VIEW
II. HARDWARE INSTALLATION
Please find the integrated metal plate in the
content and it will be the first step on this
installation. Turn the terminal which with Gen 6
base-stand up-side-down before screw-fit the
metal plate. Please notice that there are four screw
holes in the bottom of base stand which are
circled in the right picture. Take the metal plate
and match these screws holes as lower right
picture and fasten these screws.
After install the metal plate, please take the
NXT button
“+” button
OSD button
Power switch
“-“ button
Gen 6 base stand
Terminal
Integrated metal plate
Page 3
monitor and match the bottom of the panel unit into the integrated metal plate.
Screw on the pivot screw after monitor joined and the installation.
After combination, please find the VGA connector which in the right back of
LM-6801. Please VGA cable to connect to Posiflex terminal and the final step
is finished.
OSD
OSD buttons
“OSD” button: To enter OSD setup menu, or to perform function selected
in OSD operation.
“NXT” button: To go to next option function.
“” “” button: To increase setting.
“” “” button: To decrease setting.
VGA Connector
Page 4
“” “” button: To turn the monitor power ON/OFF. The monitor can be
turned OFF only when there is video signal and can be turned ON only
when there is video signal and after the “Turn Off Panel” message
vanishes. The default status is set to ON when power is supplied unless
manually turned OFF. Since this button controls only the display power
but not the display controller, please try disconnect the power cable or
the VGA cable once unfortunately the screen display goes into a mess.
OSD functions
Press “OSD” button with a normal display on the screen to activate the OSD
functions (On Screen Display adjustment). The OSD window will pop up on
the screen. On top part of this window is a Posiflex logo with the OSD
firmware version indicated to its lower right. Below this area is a row of icons
for main OSD menu. Below the main menu is a group of icons for submenu
that corresponds to one icon selected in the main menu. An analysis of the
video signal on resolution and refresh rate will be displayed at the bottom.
Applicable icons in the main menu and its subsequent menus are explained
below.
“MAIN MENU”: There are in total 5 icons in this menu:
One of the 5 icons will be displayed in inverted color to indicate its
relationship with the submenu below. Pressing “NXT” button will shift the
selected icon one by one from left to right and then wrap around to the most
left. Press “OSD” button to enter the selected sub menu. If there is no button
for OSD setting is pressed within a period of time (about 5 seconds to 1 minute
as programmed) the OSD window will disappear with all the adjusted
parameters saved. Explanations on items in sub menu are as below.
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”:
There are 3 icons in this submenu: Press “OSD” button to
select item or return to main menu. Press “NXT” button to select among
brightness, contrast and exit.
“BRIGHTNESS ADJUST”: When this item is selected, there
will be only the brightness icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase brightness. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
“CONTRAST ADJUST”: When this item is selected, there will
be only the contrast icon with an adjustment indication bar under it
between the main menu area and the video signal mode. Press “+”
button to increase contrast. Press “-” to decrease. Press “OSD” button
to save the current setting and return to “Brightness/Contrast submenu”.
Page 5
“EXIT”: Return to “Main menu”.
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:
Press “OSD” button to select item or return to main menu.
Press “NXT” button to select among auto color adjust, auto RGB reset, Color
balance adjust and exit.
“AUTO COLOR ADJUST”: Upon an “OSD” button press on
this icon the monitor will perform an automatic color adjustment and
exits the OSD window leaving 2 icons below at center of the screen.
Press “NXT” button to switch the selection. Press “OSD” button to
make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“AUTO RGB RESET”: Upon an “OSD” button press on this
icon the monitor will perform an automatic RGB reset and exits the
OSD window leaving 2 icons below at center of the screen. Press
“NXT” button to switch the selection. Press “OSD” button to make the
choice.
“ACCEPT”: Accept the reset result.
“REJECT”: Decline the reset and return to previous
setting.
“COLOR BALANCE ADJUST”: When this item is selected,
there will be 7 icons in this item: between main
menu area and the video signal mode. Press “OSD” button to select an
item or return to color adjust submenu. Press “NXT” button to select
among separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K
and exit.
“SEPARATE COLOR ADJUST”: When this item is
selected, there will be 3 adjustment indication bars between the
main menu area and the video signal mode. Press “NXT” button
to select among the 3 colors Red, Green and Blue respectively.
Press “+” button to intensify that color. Press “-” to reduce.
Press “OSD” button to save the current setting and return to
“Color balance adjust submenu”.
“4200K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 4200 degrees Kelvin.
“5000K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 5000 degrees Kelvin.
“6500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 6500 degrees Kelvin.
“7500K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 7500 degrees Kelvin.
Page 6
“9300K”: Pressing “OSD” button on this icon will set the
color balance to a color temperature of 9300 degrees Kelvin.
“EXIT”: Return to “Color adjust submenu”.
“EXIT”: Return to “Main menu”.
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this
submenu: Press “OSD” button to select item or return to
main menu. Press “NXT” button to select among auto geometry adjust,
horizontal size, phase, horizontal position, vertical position and exit.
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press
on this icon the monitor will perform an automatic geometry adjustment
and exits the OSD window leaving 2 icons below at center of the screen.
Press “NXT” button to switch the selection. Press “OSD” button to
make the choice.
“ACCEPT”: Accept the adjustment setting.
“REJECT”: Decline the adjustment setting and return to
previous setting.
“HORIZONTAL SIZE”: When this item is selected, there will
be only the horizontal size icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press “+”
button to increase horizontal size. Press “-” to decrease. Press “OSD”
button to save the current setting and return to “Geometry adjust
submenu”.
“PHASE”: When this item is selected, there will be only the
phase adjust icon with an adjustment indication bar under it between
the main menu area and the video signal mode. Press “+” or “-” button
to adjust the pixel synchronization phase for best picture display. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“HORIZONTAL POSITION”: When this item is selected, there
will be only the horizontal position icon with an adjustment indication
bar under it between the main menu area and the video signal mode.
Press “+” or “-” button to shift the screen display to right or left. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“VERTICAL POSITION”: When this item is selected, there
will be only the vertical position icon with an adjustment indication bar
under it between the main menu area and the video signal mode. Press
“+” button to shift up the screen display. Press “-” to shift down. Press
“OSD” button to save the current setting and return to “Geometry
adjust submenu”.
“EXIT”: Return to “Main menu”.
“TOOLS SUBMENU”: When this item is selected, there are 5 icons in
Page 7
this submenu: Press “OSD” button to select item or return
to main menu. Press “NXT” button to select among OSD submenu, reset to
default, phase, smoothness / sharpness adjust, mode select and exit.
“OSD SUBMENU”: When this item is selected, there are 4 icons
in this submenu: Press “OSD” button to select item or
return to main menu. Press “NXT” button to select among OSD time,
OSD horizontal position, OSD vertical position and exit.
“OSD TIME”: When this item is selected, there will be
only the OSD time icon with an adjustment indication bar under
it between the main menu area and the video signal mode. Press
“+” or “-” button to adjust the waiting time for OSD operation
before OSD termination between 5 to 60 seconds. Default is 30
seconds. Press “OSD” button to save the current setting and
return to “OSD submenu”.
“OSD HORIZONTAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to shift OSD
window right. Press “-” to shift left. Press “OSD” button to save
the current setting and return to “OSD submenu”.
“OSD VERTICAL POSITION”: When this item is
selected, there will be only the vertical position icon with an
adjustment indication bar under it between the main menu area
and the video signal mode. Press “+” button to move OSD
window downward. Press “-” to go upward. Press “OSD” button
to save the current setting and return to “OSD submenu”.
“EXIT”: Return to “Tools submenu”.
“RESET TO DEFAULT”: Pressing “OSD” button on this icon
will set all parameters back to the status when the monitor left factory.
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is
selected, there will be only the smoothness / sharpness adjust icon with
an adjustment indication bar under it between the main menu area and
the video signal mode. Press “+” button to increase smoothness of
display (decrease sharpness). Press “-” to go the other way. Press
“OSD” button to save the current setting and return to “OSD submenu”.
“MODE SELECT”: Pressing “OSD” button on this icon will
have no effect at all if the display mode is not one of the confusing
modes. The confusing modes here mean 640 x 400 or 720 x 400 in
display resolution as both mode have refresh rate of 70Hz, horizontal
frequency of 37.9KHz and pixel frequency of 31.5MHz making it
impossible for automatic select. These modes are not used in normal
Windows display.
Page 8
“EXIT”: Return to “Main menu”.
“EXIT”: Exit OSD setup with all adjustment saved.
SUPPORTED DISPLAY MODES
For video signals beyond the supported display modes, there will be a message
“Out Of Range” on middle of screen. Maximum supported color depth is 18
bits or 262,144 colors. Supported display modes are as in the table:
Display Resolution Refresh Rate (Hz)
Horizontal Frequency
(KHz)
640*400
70
37.9
640*480
60
31.5
72
37.9
75
37.5
720*400
70
37.9
800*600
56
35.1
60
37.9
72
48.1
75
46.9
1024*768
60
48.4
70
56.5
75
60
警告使用者
這是甲類的資訊產品，在居住的環
境中使用時，可能會造成射頻干
擾，在這種情況下，使用者會被要
求採取某些適當的對策。
T31454
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Posiflex LM-6801 User manual

Posiflex
Brand
Posiflex
Model
LM-6801
Category
LED displays
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents