2. Grace Company
  3. Q'nique Machine Foot Accessories

Grace Company Q'nique Machine Foot Accessories Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Grace Company Q'nique Machine Foot Accessories Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Copyright Jan 22, 2021
Grace Company
(Reproduction Prohibited)
Version 1.2
4-Piece Accessory Hopping Foot
Installation for the 21” Quilting Machine
2
Included Parts
SHCS
M3 x 8 mm (x4)
(2 pre-installed)
HDW-03-10966
Presser Foot
Collar SM21
SMP-09-14524
Standard
Hopping Foot
SMP-04-10057
Micro-Stippling
Foot
SMP-O4-11708
Ruler Foot
SMP-04-11709
Open-Toe Foot
SMP-04-11707
Hopping Foot
Height Gauge
SMP-03-12171
3
The standard hopping foot installed on your machine may not
match the standard hopping foot found in this kit.
IMPORTANT: READ FIRST
If this is the hopping foot on your
machine, go to “Upgrading the Hopping Foot”
on page 4.
If this is the hopping foot on your
machine, go to “Switching the Accessory Feet”
on page 6.
4
Upgrading the Hopping Foot
Required Parts & Tools:
Hopping
Foot Collar
Use a 3 mm Allen wrench to remove the
screw attaching the hopping foot to the
hopping foot collar on your machine.
Remove the needle thumb screw and
pull the needle from the machine.
2
1
Loosen the collar screw with a 3 mm
Allen wrench just enough that hopping
foot collar can be pulled down o the
machine.
3
Hopping Foot
Screw
Hopping
Foot
Collar
Needle
Thumb Screw
Hopping
Foot
Collar Screw
Hopping
Foot Screw
Standard
Hopping Foot
Allen Wrench 3 mm (not included)
Hopping Foot
Height Gauge
5
Slide the hopping foot collar that came
with this kit onto the press bar. Hold in
place with the hopping foot collar screw.
4
Place the upgraded standard hopping
foot onto the hopping foot collar bar.
Attach with a hopping foot screw loosely
enough that the hopping foot can slide up
and down.
5
Reinstall your machine’s needle and needle
thumb screw.
6
Set hopping foot height: move the
machine o of the fabric and drop the
needle to the lowest position. Slide the
the hopping foot height tool beneath
the foot. Tighten the hopping foot screw
with the 3 mm Allen wrench.
7
Hopping
Foot
Collar
Standard
Hopping Foot
6
Switching the Accessory Feet
Required Parts & Tools:
Open-toe Foot
Ruler Foot
OR
Stippling Foot
OR
Check the position of your hopping foot. The open toe and stippling accessory feet
can only be used if the hopping foot is set directly behind the needle. See your
machine manual for instructions on changing the hopping foot orientation.
1
Allen Wrench 3 mm
(not included)
Hopping Foot
Height Gauge
7
Remove the screw attaching the
hopping foot to your machine using a
3 mm Allen wrench.
Loosely attach one of the accessory
hopping feet onto the collar bar with a
hopping foot screw.
3
2
Hopping Foot
Screw
Accessory
Hopping Foot
Set hopping foot height: move the
machine o of the fabric and drop the
needle to the lowest position. Slide the
the hopping foot height tool beneath
the foot. Tighten the hopping foot screw
with the 3 mm Allen wrench.
4
Hopping Foot
Height Tool
Note: Reset the hopping foot height
every time the hopping foot is swapped
out.
The Grace Company
2225 South 3200 West
Salt Lake City, UT 84119
Phone: 1-800-264-0644
Fax: 801-908-8888
www.graceframe.com
/